How to Calculate Wind Load

Wind is a mass of air that moves in a mostly horizontal direction from an area of high pressure to an area with low pressure. High winds can be very destructive because they generate pressure against the surface of a structure. The intensity of this pressure is the wind load. The effect of the wind is dependent upon the size and shape of the structure. Calculating wind load is necessary for the design and construction of safer, more wind-resistant buildings and placement of objects such as antennas on top of buildings.

Wind Load Calculator

Method 1

Method 1 of 3:

Calculating Wind Load Using the Generic Formula

Download Article

The generic formula for wind load is F = A x P x Cd where F is the force or wind load, A is the projected area of the object, P is the wind pressure, and Cd is the drag coefficient. This equation is useful for estimating the wind load on a specific object, but does not meet building code requirements for planning new construction.^{[1]XResearch source}
2
Find the projected area A. This is the area of the two-dimensional face that the wind is hitting. For a full analysis, you will repeat the calculation for each face of the building. For example, if a building has a west face with an area of 20m², use that value for A to calculate the wind load on the west face.^{[2]XResearch source}
- The formula to calculate area depends on the shape of the face. For a flat wall, use the formula Area = length x height. Approximate the area of a column face with Area = diameter x height.
- For SI calculations, measure A in square meters (m²).
- For imperial calculations, measure A in square feet (ft²).
Advertisement
3
Calculate wind pressure. The simple formula for wind pressure P in imperial units (pounds per square foot) is $P=0.00256V^{2}$ $How.com.vn English: P=0.00256V^{2}$ , where V is the speed of the wind in miles per hour (mph). To find the pressure in SI units (Newtons per square meter), instead use $P=0.613V^{2}$ $How.com.vn English: P=0.613V^{2}$ , and measure V in meters per second.^{[3]XResearch source}
- This formula is based on the American Society of Civil Engineers code. The 0.00256 coefficient is the result of a calculation based on typical values for air density and gravitational acceleration.
- Engineers use a more accurate formula to take into account factor such as the surrounding terrain and type of construction. You can look up one formula in ASCE code 7-05, or use the UBC formula below.
- If you're not sure what the wind speed is, look up the peak wind speed in your area using the Electronic Industries Alliance (EIA) standard. For example, most of the U.S. is in Zone A with 86.6 mph wind, but coastal areas might lie in Zone B (100 mph) or Zone C (111.8 mph).
4
Determine the drag coefficient for the object in question. Drag is the force that air exerts on the building, affected by the building's shape, the roughness of its surface, and several other factors. Engineers typically measure drag directly using experiments, but for a rough estimate you can look up a typical drag coefficient for the shape you are measuring. For example:^{[4]XResearch source}
- The standard drag coefficient for a long cylinder tube is 1.2 and for a short cylinder is 0.8. These apply to antenna tubes found on many buildings.
- The standard coefficient for a flat plate such as the face of a building is 2.0 for a long flat plate or 1.4 for a shorter flat plate.
- The drag coefficient has no units.
Using the values determined above, you can now calculate wind load with the equation F = A x P x Cd.^{[5]XResearch source}
6
For example, let’s say you want to determine the wind load on an antenna that is 3 feet long with a diameter of 0.5 inches in a gust of 70mph winds.
- Start by estimating the projected area. In this case, $A=dw=(3ft)(0.5in)(1ft/12in)=0.125ft^{2}$
- Calculate the wind pressure: $P=0.00256V^{2}=0.00256(70^{2})=12.5psf$ .
- For a short cylinder the coefficient of drag is 0.8.
- Plugging into the equation: $F=APCd=(0.125ft^{2})(12.5psf)(0.8)=1.25lbs.$
- 1.25 lbs is the amount of wind load on the antenna.

Method 2

Method 2 of 3:

Calculating Wind Load Using the Electronic Industries Alliance Formula

Download Article

The formula for wind load is F = A x P x Cd x Kz x Gh, where A is the projected area, P is wind pressure, Cd is the drag coefficient, Kz is the exposure coefficient, and Gh is the gust response factor.^{[6]XResearch source} This formula takes a few more parameters into account for wind load. This formula is generally used to calculate wind load on antennas.
2
Understand the variables of the equation. In order to use an equation properly, you must first understand what each variable stands for and what its associated units are.
- A, P, and Cd are the same variables used in the generic equation.
- Kz is the exposure coefficient and it is calculated by taking into account the height from the ground to the midpoint of the object. The units of Kz are feet.
- Gh is the gust response factor and it is calculated by taking into account the entire height of the object. The units of Gh are 1/feet or ft^-1.
3
Determine projected area. The projected area of your object is dependent upon its shape and size. If the wind is hitting a flat wall, the projected area is easier to calculate than if the object is rounded. Projected area will be an approximation of the area that the wind comes in contact with. There is no one formula for calculating projected area, but you can estimate it with some basic calculations. Units for area are ft².
- For a flat wall, use the formula Area = length x width, measuring the length and width of the wall where the wind is hitting it.
- For a tube or column, you can also approximate the area using length and width. In this case, the width will be the diameter of the tube or column.
4
Calculate wind pressure. Wind pressure is given by the equation P = 0.00256 x V², where V is the speed of the wind in miles per hour (mph). The unit for wind pressure is pounds per square foot (psf).
- For example, if the wind speed is 70 mph, the wind pressure is 0.00256 x 70² = 12.5 psf.
- An alternative to calculating wind pressure at a particular wind speed is to use the standard for various wind zones. For example, according to the Electronic Industries Alliance (EIA) most of the U.S. is in Zone A with 86.6 mph wind, but coastal areas might lie in Zone B (100 mph) or Zone C (111.8 mph).
5
Determine the drag coefficient for the object in question. Drag is the net force in the direction of flow due to pressure on the surface of an object.^{[7]XResearch source} The drag coefficient represents the drag of an object through a fluid and is dependent upon the shape, size, and roughness of an object.
- The standard drag coefficient for a long cylinder tube is 1.2 and for a short cylinder is .8 These apply to antenna tubes found on many buildings.
- The standard coefficient for a flat plate such as the face of a building is 2.0 for a long flat plate or 1.4 for a shorter flat plate.
- The difference between drag coefficients for flat and cylinder items is approximately 0.6.
- The drag coefficient has no units.
6
Calculate the exposure coefficient, Kz. Kz is calculated using the formula [z/33]^(2/7), where z is the height from the ground to the midpoint of the object.
- For example, if you have an antenna that is 3 ft long and 48 ft off the ground, z would be equal to 46.5 ft.
- Kz = [z/33]^(2/7) = [46.5/33]^(2/7) = 1.1 ft.
7
Calculate the gust response factor, Gh. Gust response factor is calculated with the equation Gh = .65+.60/[(h/33)^(1/7)] where h is the height of the object.
- For example, if you have an antenna that is 3 ft long and 48 ft off the ground, Gh = .65+.60/[(h/33)^(1/7)] = .65+.60/(51/33)^(1/7) = 1.22 ft^-1
8
Calculate the wind load. Using the values determined above, you can now calculate wind load with the equation F = A x P x Cd x Kz x Gh. Plug in all of your variables and do the math.
- For example, let’s say you want to determine the wind load on an antenna that is 3 feet long with a diameter of 0.5 inches in a gust of 70mph winds. It is placed on top of a 48 ft high building.
- Start by calculating the projected area. In this case, A = l x w = 3 ft x (0.5in x (1 ft/12 in)) = 0.125 ft².
- Calculate the wind pressure: P = 0.00256 x V² = 0.00256 x 70² = 12.5 psf.
- For a short cylinder the coefficient of drag is 0.8.
- Calculate the exposure coefficient: Kz = [z/33]^(2/7) = [46.5/33]^(2/7) = 1.1 ft.
- Calculate the gust response factor: Gh = .65+.60/[(h/33)^(1/7)] = .65+.60/(51/33)^(1/7) = 1.22 ft^-1
- Plugging into the equation: F = A x P x Cd x Kz x Gh = 0.125 x 12.5 x 0.8 x 1.1 x 1.22 = 1.68 lbs.
- 1.68 lbs is the amount of wind load on the antenna.

Method 3

Method 3 of 3:

Calculating Wind Load Using the Uniform Building Code (UBC) ’97 Formula

Download Article

1
Define the UBC ’97 formula. This formula was developed in 1997 as part of the Uniform Building Code (UBC) for calculation of wind load. The formula is F = A x P, were A is the projected area and P is the wind pressure; however, this formula has an alternate calculation for wind pressure.
- Wind pressure (PSF) is calculated as P= Ce x Cq x Qs x Iw, where Ce is the combined height, exposure and gust response factor, Cq is a pressure coefficient (it is equivalent to the drag coefficient in the previous two equations), Qs is wind stagnation pressure, and Iw is importance factor. All of these values can be calculated or obtained from the appropriate tables.
2
Determine projected area. The projected area of your object is dependent upon its shape and size. If the wind is hitting a flat wall, the projected area is easier to calculate than if the object is rounded. Projected area will be an approximation of the area that the wind comes in contact with. There is no one formula for calculating projected area, but you can estimate it with some basic calculations. Units for area are ft².
- For a flat wall, use the formula Area = length x width, measuring the length and width of the wall where the wind is hitting it.
- For a tube or column, you can also approximate the area using length and width. In this case, the width will be the diameter of the tube or column.
3
Determine Ce, the combined height, exposure, and gust response factor. This value is chosen based on table 16-G of UBC and takes into account three terrain exposures with various heights and Ce values for each.
- “Exposure B is terrain with buildings, trees or other surface irregularities covering at least 20 percent of the surrounding area and extending 1.6 kilometers or more from the site.”
- “Exposure C has terrain that is flat and generally open, extending 0.8 km or more from the site.”
- “Exposure D is the most severe, with basic wind speeds of 129 km/hr or greater and terrain that is flat and unobstructed facing large bodies of water.”
4
Determine the pressure coefficient for the object in question. The pressure coefficient, Cq, is the same as the drag coefficient (Cd). Drag is the net force in the direction of flow due to pressure on the surface of an object.^{[8]XResearch source} The drag coefficient represents the drag of an object through a fluid and is dependent upon the shape, size, and roughness of an object.
- The standard drag coefficient for a long cylinder tube is 1.2 and for a short cylinder is .8 These apply to antenna tubes found on many buildings.
- The standard coefficient for a flat plate such as the face of a building is 2.0 for a long flat plate or 1.4 for a shorter flat plate.
- The difference between drag coefficients for flat and cylinder items is approximately 0.6.
- The drag coefficient has no units.
5
Determine the wind stagnation pressure. Qs is the wind stagnation pressure and is equivalent to the wind pressure calculation from the previous equations: Qs = 0.00256 x V², where V is the speed of the wind in miles per hour (mph).
- For example, if the wind speed is 70 mph, the wind stagnation pressure is 0.00256 x 70² = 12.5 psf.
- An alternative to this calculation is to use the standards set for various wind zones. For example, according to the Electronic Industries Alliance (EIA) most of the U.S. is in Zone A with 86.6 mph wind, but coastal areas might lie in Zone B (100 mph) or Zone C (111.8 mph).
6
Determine importance factor. Iw is the importance factor and can be determined using table 16-K of the UBC. It is a multiplier used in calculating loads that takes into account the use of the building. If a building contains hazardous materials, its importance factor will be higher than that of a traditional building.^{[9]XResearch source}
- Calculations for buildings with standard use have an importance factor of one.
7
Calculate the wind load. Using the values determined above, you can now calculate wind load with the equation F = A x P = A x Ce x Cq x Qs x Iw . Plug in all of your variables and do the math.
- For example, let’s say you want to determine the wind load on an antenna that is 3 feet long with a diameter of 0.5 inches in a gust of 70mph winds. It is placed on top of a 48 ft high standard building in an area with an exposure B terrain.
- Start by calculating the projected area. In this case, A = l x w = 3 ft x (0.5in x (1 ft/12 in)) = 0.125 ft².
- Determine Ce. Based on table 16-G, using the height of 48 ft and exposure B terrain, Ce is 0.84.
- For a short cylinder the coefficient of drag or Cq is 0.8.
- Calculate Qs: Qs = 0.00256 x V² = 0.00256 x 70² = 12.5 psf.
- Determine importance factor. This is a standard building therefore, Iw is 1.
- Plugging into the equation: F = A x P = A x Ce x Cq x Qs x Iw = 0.125 x 0.84 x 0.8 x 12.5 x 1= 1.05 lbs.
- 1.05 lbs is the amount of wind load on the antenna.

Community Q&A

Search

Add New Question

Question
I want to create a 12' diameter cylinder grain tower that's 55' high, and has a smooth surface and dome roof. How many yards of concrete does it take to anchor it for an estimated maximum wind force of 110 MPH?
Community Answer
The force will be around 0.0012 x ((88/60) x (110))^2. The 88/60 converts from mph to fps, and the answer is around 31 pounds per square feet. If we add the height of the dome, it is 55 + 6 = 61' tall, and 12' wide, so the area is 12 x 61 = 732 square feet. Total force acting on the tower is about 732 x 31 = 22,692 pounds, over ten tons. The force will be greatest near the top, because wind is strongest higher up, and the top will be more turbulent. Without knowing the wind gradient one can't be sure where the net force acts. You'll have to pour enough concrete to withstand over ten tons sideways near the top of your tower. We're out of space here - good luck!
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 12 Helpful 24
Question
How can I convert wind speed to wind pressure?
Community Answer
.0012 x the speed in feet per second squared is close enough at sea level, so that 88 FPS would give you .0012 x 88 x 88 = 9.3 pounds per square foot. 88 FPS is 60 MPH, almost 100 KPH.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 8 Helpful 19
Question
Which instrument is used to measure wind speed?
Community Answer
An anemometer is used to measure wind speed. It must be recorded for 12 months to determine accurate information before the site can be detemined as usable for constructing a wind farm. Average Wind Speed is at least 5.95 meters per second to be considered viable for wind turbine energy production. It is suggested that you check out with global maps data, i.e. Valhalla, for wind speed complete information.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 5

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Know that wind velocity varies at various distances from the ground. Wind speed increases with structural height and is most unpredictable closer to the ground, because it is affected by interacting with things on the ground.
Thanks
Helpful0 Not Helpful0
Be aware that this unpredictability can make it difficult to make accurate wind calculations.
Thanks
Helpful0 Not Helpful0