How to Make an FM Antenna

This How.com.vn teaches you how to create your own FM antenna in order to increase your FM receiver's range. Depending on your preferred range, you can do this by using either coaxial cable or speaker wire.

Method 1

Method 1 of 2:

Using a Coaxial Cable

Download Article

1
Gather the necessary materials. In order to make a vertical antenna from a coaxial cable, you will need the following materials:^{[1]XResearch source}
- 50 ohm (or 75 ohm) coaxial wire with copper shielding
- FM receiver with a coaxial connector
- 3/8-inch copper tubing
- Wire cutters
- Hacksaw
- Soldering equipment
2
Calculate the length of your antenna. This will determine both how much of the coaxial cable you have to strip and how long your copper tubing should be:
- Divide 468 by the frequency to which you want to connect (e.g., 468/108MHz would become 4.3).
- Divide the resulting number by 2 (e.g., 4.3/2 would become 2.15).
- Multiply the resulting number by 12 inches (30.5 cm) to find the antenna length (e.g., 2.15*12 inches would become 25.8 inches).^{[2]XResearch source}
Advertisement
3
Cut off one end of the coaxial cable. While you'll want to leave one end of the coaxial cable intact in order for it to serve as the connector, the other end will need to be removed.
- You can use your wire cutters or a hacksaw to do this.
4
Strip half of the antenna's overall length from the end of the coaxial cable. You'll need to remove each layer of shielding until you arrive at the white layer surrounding the coaxial cable itself.
- For example, if your antenna is supposed to be six inches per your calculations, you'll remove three inches of shielding.^{[3]XResearch source}
- You'll need to remove the copper shielding during this process. The easiest way to do so is by making a shallow incision with the hacksaw all the way around the shielding and then attempting to strip it off from there.
5
Cut the copper tubing to half of the antenna's overall length. The copper tubing will comprise the other half of your antenna's receiver, so it should be the same length as the section that you just stripped.
- Again, if you're using a six-inch antenna, the copper tubing will be three inches.
Slide the copper tubing onto the coaxial cable's stripped end, then slide it down to the
Solder the coaxial cable's shielding to the tubing. You can do this by removing the PVC (black) shielding from around an inch of the coaxial cable directly below the unshielded part, peeling it back with a pair of pliers to form a lip, and then using your soldering pen to connect the lip to the copper tubing.
The remaining coaxial connector should plug into the receiver's coaxial antenna port, which makes the rest of the antenna placement fairly simple.^{[4]XResearch source}
9
Place the antenna. Once the antenna is plugged in, angle it toward the nearest station and secure it in place if necessary.
- The fewer obstructions between your antenna and the nearest FM station, the stronger your signal will be.
- Your coaxial cable may be stiff enough to stand on its own without needing support, but you can use stables or any adhesive to prop up your antenna as needed.

Method 2

Method 2 of 2:

Using Speaker Wire

Download Article

1
Understand when to use this method. If your connection to an FM station is mostly fine but requires some fine-tuning from time to time, you can use speaker wire as a quick range-extender to improve the quality of your connection.
- Speaker wire is not an ideal solution to long-range issues. If you're having trouble receiving a signal at all, you should try using coaxial cable instead.^{[5]XResearch source}
2
Gather the necessary materials. In order to craft a crude antenna from speaker wire, you'll need the following items:^{[6]XResearch source}
- 10 feet of speaker wire
- FM receiver with clamp-and-hold (or post) FM connections
- Wire strippers
Using a knife or a pair of pliers, separate the top three feet of the speaker wire tubes from each other. You should be left with three feet of spit wire and seven feet of intact wire.^{[7]XResearch source}
You'll do this by bending each of the split wire ends at a 90-degree angle to the seven-foot section of wire.
Strip the bottom two inches of insulation from the [[speaker wire. Use the wire strippers to do so. This will expose two bare wires at the bottom of the "T" shape.
6
Find your receiver's antenna connections. These two connections will normally be marked "FM EXT" or "ANT EXT", but you'll almost always see "FM" somewhere near the connection; you should also see the word "Balanced" or "BAL" near the appropriate connections.
- FM receivers can have either clamp-and-hold connectors or post connectors. Clamp-and-hold connectors resemble literal clamps, while post connectors resemble knobs with exposed metal between them and the receiver itself.^{[8]XResearch source}
7
Connect the bottom of the "T" to the receiver. Use each of the exposed wires at the bottom of the "T" shape to connect to each of the FM connections.
- If there's only one FM connection, you can twist the two bare wires at the bottom of the "T" together to form one wire that can connect to the clamp or post.
8
Place the antenna. Ideally, you'll place your antenna as high up and as close to the nearest station as possible. In some cases, this may mean threading your antenna along the top of a wall, or even running it outside.
- You may have to move the FM receiver in order to make this possible.

Community Q&A

Search

Add New Question

Question
What is an FM dipole antenna?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
The dipole antenna is a simple antenna consisting of two rods or wires of exactly the same type and length, which serve as the conductive elements for the electrical energy. The current is applied (transmitter) or taken (receiver) from between the two halves of the antenna. To help you get an image, just think of the "rabbit’s ears" used for broadcast television sets. You can find greater detail on how this antenna works in the Wikipedia article "Dipole antenna."
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 4 Helpful 4
Question
Can I use a CB antenna for FM radio?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
It is possible to use a CB antenna for FM radio. Some people like doing this to avoid having too many antennas or to keep things tidy in a vehicle or other place. It can be helpful to use a CB/FM splitter, that enables you to get the CB and FM reception. You can find instructions for using the CB antenna as an FM radio on various CB users’ forums online.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 6 Helpful 13
Question
How do FM antennas work?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
A transmitter FM antenna creates electrical signals or electrical energy and turns this energy into radio waves (electrons travel back and forth along the antenna, creating electromagnetic radiation). The electromagnetic radiation is better known as "radio waves" and these waves then travel long distances, carrying the sounds, songs, talk, etc. you’re familiar with on radio. A receiver antenna (on your radio, for example) captures the radio waves that have been transmitted, and the electric current generated is converted by your radio into the sounds you enjoy listening to. The bigger or more powerful the antennas, the farther the radio waves will travel.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 10

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Both antennae constructed here are "balanced" and will be inconvenient to connect to the typical "unbalanced" telescoping antenna.
Thanks
Helpful10 Not Helpful1
Coaxial cables and speaker wire are both fairly cheap. If you already have the proper tools to create your preferred antenna, you can make an antenna for a fraction of the price of purchasing a new FM antenna.
Thanks
Helpful8 Not Helpful1

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

If your antenna is placed outside, you should implement some form of lightning protection.
Thanks
Helpful5 Not Helpful1
Antennae that are placed outdoors should have weatherproofing measures (e.g., waterproof coating) in place.
Thanks
Helpful3 Not Helpful2