This article was co-authored by Mantas Silvanavicius. Mantas Silvanavicius is a Licensed Electrician and the Owner of M+S Electric based in Las Vegas, Nevada. With more than 20 years of experience, he specializes in home electrical installations, testing, and wiring. Mantas and his team have completed projects for companies such as Seiko and Springhill Suites by Marriott. M+S Electric is licensed, bonded, and insured.
There are 7 references cited in this article, which can be found at the bottom of the page.
This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources.
This article has been viewed 1,501,659 times.
Need to know how to calculate series resistance, parallel resistance, and a combined series and parallel network? If you don't want to fry your circuit board, you do! This article will show you how in just a few easy steps. Before reading this, please understand that resistors do not actually have an "inside" and an "outside" to them. The use of "in" and "out" is merely a figure of speech to help novices understand the wiring concepts.
Steps
Help Calculating Resistance
Community Q&A
- QuestionHow do I calculate the supply current?Community AnswerYou divide your total voltage by total resistance. For example let's say your voltage is 200V and your total resistance is 25 ohm, so it's IT=VT/ RT=200/25 = 8A.
- QuestionHow do I connect a resistor to get the minimum resistance?Community AnswerNet resistance is minimum when all the resistors are connected in parallel.
- QuestionHow do I find the equivalent resistance between A and B arranged in a triangle?Community AnswerSuppose A and B are the extremities of the base of the triangle. The resistor (R 1) between A and B would be parallel with the equivalent resistance of the other two, which are essentially in series. Then, R 2 and R 3 have an equivalent resistance: RE = R 2 + R 3. RE and R 1 are parallel, therefore the equivalent resistance is the reciprocal of the sum of the reciprocals of RE and R 1.
Video
Some Facts
- Understand resistance. Every material that conducts electrical current has resistivity, which is the resistance of a material to electrical current.
- Resistance is measured in ohms. The symbol used for ohms is Ω.
- Different materials have different resistance properties.
- Copper, for example, has a resistivity of 0.0000017(Ω/cm3)
- Ceramics have a resistivity around 1014(Ω/cm3)
- The higher the number, the greater the resistance to electrical current. You can see that copper, which is commonly used in electrical wiring, has a very low resistivity. Ceramic, on the other hand, is so resistive that it makes an excellent insulator.
- How you wire multiple resistors together makes much difference on the overall performance of a resistive network.
- V=IR. This is Ohm's law, defined by George Ohm in the early 1800s. If you know any two of these variables, you can easily calculate the third.
- V=IR: Voltage (V) is the product of current (I) * resistance (R).
- I=V/R: Current is the quotient of voltage (V) ÷ resistance (R).
- R=V/I: Resistance is the quotient of voltage (V) ÷ current(I).
Tips
- The equivalent resistance (Req) is always smaller than the smallest contributor for a parallel circuit; it is always greater than the greatest contributor for a series circuit.Thanks
- Calculate the resistance using the ohms law or the power law:Thanks
- Remember, when resistors are in parallel, there are many different means to an end, so the total resistance will be smaller than each pathway. When resistors are in series, the current will have to travel through each resistor, so the individual resistors will add to give the total resistance for the series.Thanks
- V = R * I- P = V * I we can replace V by RI so.....- P = RI * I- P = R I^2-Example: a lamp of 75watt lighted by a tension of 220 v, how to find its resistance? 1 - P = V * I - I = P/V => 75/220 = 0.34 ohm - P = RI^2 - 75W = R * 0.34^2 - R = 75/0.1156 = 648A- Let's check if it is the same with the other method.2 - V = R * I. - R = V/I - R = 220/0.34 = 647A almost the same ;).
References
- ↑ https://phys.libretexts.org/Bookshelves/University_Physics/Book%3A_University_Physics_(OpenStax)/Book%3A_University_Physics_II_-_Thermodynamics_Electricity_and_Magnetism_(OpenStax)/10%3A_Direct-Current_Circuits/10.03%3A_Resistors_in_Series_and_Parallel
- ↑ https://www.physicsclassroom.com/class/circuits/Lesson-4/Combination-Circuits
- ↑ http://physics.bu.edu/py106/notes/Circuits.html
- ↑ https://www.omnicalculator.com/physics/parallel-resistor
- ↑ https://www.electronics-tutorials.ws/resistor/res_5.html
- ↑ https://flexbooks.ck12.org/cbook/ck-12-physics-flexbook-2.0/section/17.5/primary/lesson/combined-series-parallel-circuits-phys/
- Handbook for Sound Engineers: The New Audio Cyclopedia, Glen Ballou, Editor
About This Article
Reader Success Stories
- "The subliminal hypnosis learning for this article is really loud, thanks for the great stuff."
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.