Download ArticleDownload ArticleThis article was co-authored by How.com.vn Staff. Our trained team of editors and researchers validate articles for accuracy and comprehensiveness. How.com.vn's Content Management Team carefully monitors the work from our editorial staff to ensure that each article is backed by trusted research and meets our high quality standards.
The How.com.vn Video Team also followed the article's instructions and verified that they work.
This article has been viewed 127,041 times.
Learn more...
Rubber is a common elastic substance, used everywhere from gloves to gaskets. Like an old T-shirt that has seen many runs through the dryer, rubber shrinks when exposed to heat. You can easily shrink rubber using hot water or by blowing hot air onto it. Soon enough, you will be able to shrink a rubber glove to fit your hand or fit a gasket into a tight spot with ease.
Steps
Run hot water over the rubber. At first, try using tap water. If the rubber is weak enough, the water will eventually force the rubber to contract and shrink.[1]- If the hot tap water has no effect, boiling the rubber may be more effective.
- Place the rubber in boiling water if hot tap water fails to shrink the rubber. The high heat will force the rubber to shrink if you allow it to boil for 5 to 10 minutes.[2]
- In some cases, boiling will return the rubber object to the desired size and shape just by removing any dirt and debris that has collected. If the water is dirty after the rubber is removed, this is likely the case.
- The boiling point of rubber is much higher than the boiling point of water, but take care that the rubber is not damaged by looking for signs of wear, such as spots melting away or debris floating to the surface.[3]
Advertisement - Bend the rubber into shape. If there is a specific shape that the rubber must fit, you can try reshaping it before it cools.[4]
- Be sure that the rubber has cooled enough to be handled, but not so much that it is fully rigid. Gloves may be helpful for this task.
Place the rubber object on a heat-proof surface. Whether you put it on a plate or a piece of bakeware, make sure that you will not have to make contact with the rubber while you are heating it up.- Wearing eye protection and a dust mask will ensure that you are not harmed by the heat or the possibility of smelly fumes. While it is just a blow dryer and the risk is low, taking precautions is never a bad idea.
Set the blow dryer to the highest heat setting. You will want to be sure that you are shrinking the rubber effectively. [5]- Blow hot air on the rubber. Try to be as uniform as possible, spreading the heat around evenly so that it can fully penetrate the rubber and shrink it equally all around. Apply heat for around 5 minutes, going for longer if necessary. [6]
- The rubber may begin to emit a slight smell. While it is highly unlikely, check that you are not burning the rubber by looking for signs of damage or darkening.
Allow the rubber object to fully cool before handling. The heat required to shrink rubber could hurt you, so it is best to handle it with gloves or wait for it to cool down.
Expert Q&A
Tips
Warnings
- If you plan to use the blow dryer method, consider using protection, such as goggles, gloves, and dust masks to ensure your safety.Thanks
References
- ↑ https://www.physlink.com/education/askexperts/ae478.cfm
- ↑ https://thepeasantblog.wordpress.com/2016/03/26/how-to-shrink-a-o-ring-or-gasket/
- ↑ https://www.reference.com/science-technology/melting-point-rubber-7866027e204cc4a4
- ↑ https://www.reference.com/science-technology/melting-point-rubber-7866027e204cc4a4
- ↑ https://www.reference.com/science/make-rubber-shrink-681ec9d43a238717
- ↑ https://www.reference.com/science/make-rubber-shrink-681ec9d43a238717
About This Article
If you have a glove, gasket, or other rubber item that’s a little too big, you can shrink it with some hot water. Depending on how strong the rubber is, it may be enough to just run some hot water over it from your faucet. If that doesn’t work, boil some water on the stove and put the rubber item in it for 5 to 10 minutes. Carefully take the item out of the hot water with some tongs, then allow it to cool for a few minutes. If you need to reshape the rubber, work it a little with your hands while it’s still warm, but cool enough to handle safely. Keep reading to learn how to shrink rubber with a blow dryer!
Reader Success Stories
"We were running out of smaller rubber gloves and had only a box of the bigger ones left. Our work requires precision while using the gloves and therefore the article was of great help, enabling us to continue shipping trucks and other cargo. Thanks!"..." more
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
