Download ArticleDownload ArticleHow.com.vn is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time.
This article has been viewed 65,130 times.
Learn more...
Periodically, your Honeywell QuietSet tower fan will accumulate dust, lint, hair or other debris and require cleaning. This takes a little time, patience and confidence, but can be accomplished with moderate skill.
Steps
Download Article
Turn off the fan and unplug it from the electrical outlet leaving it unplugged throughout the entire process.
Tools required are a philips screwdriver and an appropriately sized allen wrench.Advertisement
Place the unit on its side (preferably on an old towel to prevent scratching the unit) and unscrew the 2 thumbscrews on the bottom of the fan and set them aside. Do not remove the screws holding the rubber feet in place.
Carefully separate the base into its two halves by pulling the halves apart from one another. They simply snap together and apart.
With the fan still on its side, turn it so that the back faces you. Remove the 2 screws at the bottom sides using an allen wrench and set them aside. Toward the bottom center, remove the single screw using an allen wrench and set it aside. Remove the 4 screws at the top with a phillips screwdriver and set those aside.
Very carefully separate the control panel from the top of the fan from the back. There are 2 internal screws at the front of the fan that will need to be removed. Pulling too hard can break the tabs securing the control panel to the fan! Once separated at the back, slide the philips screwdriver in to either side and unscrew the 2 screws holding the control panel in place and set them aside.
Note that there is a small, translucent tab at the top center on the front. It holds the remote control sensor. If this falls out, set it aside for later when reassembling the fan.
The back of the fan should now separate fully from the front. Carefully lift straight up if you have difficulty in separating the halves as failure to do so could result in cracked or broken screw housings.
There are now 6 screws that hold the internal wind tunnel in place.Be careful not to pull too hard as the wiring between the control panel and the motor should not be stressed. Remove those 6 screws with a philips screwdriver and set them aside. Loosen the set screw on the motor by 3 or 4 full turns. From the top, lift the cylindrical fan blades and pull away from the motor. Slip the cap off the top of the fan blades and set it aside. The fan blades should (perhaps with some coaxing) separate freely.
Be careful in pulling the fan blades out as the wiring from the control panel and the motor should not be stressed.
Carefully separate the wind tunnel from the front housing. Be sure to lift straight up to avoid cracking or breaking screw housings.
The entire fan can now be cleaned. Using any of the following methods:- Use a can of compressed air to clean the unit followed by wiping down with a soft cloth (best performed outside).
- Vacuum with a soft brush followed by wiping down with a soft cloth.
- Wipe-down fully with a soft, damp cloth (avoids problems with inhaling dust due to allergies).
Reverse the process being careful to ensure that the wiring is routed as it was originally, the remote control sensor is in place, and that the translucent tab is back in its original place.
Charles Platt, Tinkerer and Circuitry ExpertWhen disassembling any appliance, patience and care are key. Meticulously organize each screw and component, noting wiring connections. Use compressed air, soft brushes and isopropyl alcohol to remove debris without damaging fragile parts. Reassembly is the reverse, taking care to firmly seat components and not overtighten screws. With mindfulness and the proper tools, these quiet machines can be refreshed to run smoothly for years more.
Expert Q&A
Tips
- To facilitate putting the unit back together with the screws in their proper locations, I create an area to lay the screws in a pattern resembling their origin. You can also put them on a piece of paper and label their locations.Thanks
Warnings
- Failure to unplug the fan while it is being disassembled or at any point during disassembly could result in shock, discomfort or death.Thanks
About This Article
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
