How to Build a Water Pump

Building an energy efficient mini water pump is a cool project that you can easily do at home. In this article, we'll teach you everything you need to know to build a fully functional DIY water pump. First, we'll explain how to assemble the pump using simple materials and tools. Then, we'll walk you through how to connect the motor and start pumping water through it. Read on to get started!

Part 1

Part 1 of 2:

Assembling the Impeller

Download Article

1
Fit a PVC pipe into 1 of the branches of a PVC tee socket. Take a 10 in (25 cm) long, 1 inch (2.5 cm) diameter PVC pipe and slide it into 1 of the branch openings of a 1 inch (2.5 cm) diameter PVC tee socket, leaving the other end open. Push the pipe far enough into the tee socket to hold it securely without blocking the run opening, which is the single opening that branches into 2.^{[1]XResearch source}
- You may need to warm up the end of the PVC pipe in hot water to soften it enough to fit into the tee socket.
- Look for PVC pipes and PVC tee sockets at hardware stores, home improvement stores, department stores, and online.
2
Insert a 3 in (7.6 cm) long PVC pipe into the run of the tee socket. Once the longer PVC pipe has been fitted into 1 of the branch openings of the tee socket, take a smaller length of pipe and slide it into the run opening. Push it far enough into the tee socket to be held in place, but not so far that it’s flush against the back wall of the tee socket.^{[2]XResearch source}
- If you insert the pipe too far into the tee socket, the water won’t be able to flow through it.
Tip: Use a hacksaw or a pipe cutter to cut longer lengths of PVC pipe down to size for your water pump.
Advertisement
3
Cut sheet metal to fit the diameter of the pipe for the impeller blade. Take a strip of sheet metal about ¹⁄₈ inch (0.32 cm) thick and place it on top of the PVC pipe. Use a marker to trace the size of the inside of the pipe over the piece of metal. Take a pair of tin snips or wire cutters to trim the sheet metal to size.^{[3]XResearch source}
- Slide the piece of metal in and out of the pipe to make sure it fits.
- The sheet metal will serve as the impeller that rotates and drives water through the pump.
4
Clip the outer edges of the metal to form a propeller shape. Take a pair of tin snips or wire cutters and clip the outer edges of the piece of metal about ¹⁄₄ inch (0.64 cm) in toward the center. Make 6 cuts around the metal, then pry the edges up slightly so they form a raised, propeller-like shape.^{[4]XResearch source}
- Use your fingers or the tin snips or wire cutters to pry the edges up slightly.
5
Insert a bicycle spoke through the center of the metal and solder it. Find the center of the piece of sheet metal and punch a hole through it with a centerpunch, nail, or another sharp object. Slide a 10 in (25 cm) bicycle spoke through the hole so the sheet metal is on the end of the spoke. Take a soldering iron and apply solder to the top and bottom of the sheet metal to bond it to the spoke.^{[5]XResearch source}
- If you aren’t used to it, practice soldering first before you attach the sheet metal to the bicycle spoke.
- You can find soldering irons at craft supply stores and online.
- Look for bicycle spokes at bicycle repair shops, department stores, and online.
Warning: Soldering irons heat up to very high temperatures and are a potential fire hazard. Be very careful when you’re using one and don’t place it down on a flammable surface while it’s still on.
6
Solder a rotor to the other end of the bicycle spoke. Take a rotor that fits onto a 12V DC motor and connect it to the other end of the bicycle spoke. Use a soldering iron to solder the rotor onto the end of the spoke so it’s firmly connected. Allow the solder to cool completely and wiggle the rotor to make sure it’s securely attached.^{[6]XResearch source}
- If the bicycle spoke is curved at the end, use a pair of wire cutters to clip off the curve so it’s straight.
- You can find a rotor for a 12V DC motor at hobby shops that sell parts for remote-controlled airplanes and vehicles, as well as online.

Part 2

Part 2 of 2:

Connecting the Motor

Download Article

1
Drill a hole through a piece of plastic to fit the rotor end of the motor. Place the end of the 12V DC motor with the small rod that the rotor fits onto against a sheet of plastic at least ¹⁄₈ inch (0.32 cm) thick and trace the outline of it with a marker. Take a power drill and attach a bit that matches the size of the outline on the plastic. Drill through the plastic to create an opening that fits your motor.^{[7]XResearch source}
- The motor needs to fit snugly into the piece of plastic to create a tighter seal.
- You can find thin squares of plastic at hardware stores, home improvement stores, and online.
2
Slide the rotor end of the motor into the slot and seal it with hot glue. Fit the motor into the opening you drilled in the plastic and use a glue gun to apply hot glue where the motor connects to the plastic. Apply pressure to the motor to hold it in place for about 10 seconds so the glue can harden enough to remain attached.^{[8]XResearch source}
- The glue will also help keep water from getting onto the motor when the pump is working.
- Look for hot glue and hot glue guns at craft supply stores, department stores, and online.
3
Insert the motor into the opening on the rotor to connect it. Slide the small rod sticking out of the rotor end of the motor into the opening on the rotor that’s connected to the bicycle spoke. Push them together or rotate the rotor to tighten it so they’re securely connected.^{[9]XResearch source}
- Some rotors may click or snap into place on the motor.
4
Fit the impeller into the open branch of the tee socket and seal it with glue. Once the glue is dry, slide the end of the bicycle spoke with the impeller on it into the open branch of the tee socket. Apply hot glue to the top of the branch socket and press the plastic sheet with the motor attached to it against it. Hold it in place for about 10 seconds so it sticks. Allow the glue to dry for about 10 minutes.^{[10]XResearch source}
- Keep pressure on the motor and the tee joint so the glue creates a tight seal.
Locate the 2 wires on the back of your 12V DC motor. Connect the red wire to the positive terminal on a 12V battery, which will have a plus sign (+) on it. Then, connect the black wire to the negative terminal, which will have a minus symbol (-) on it. The motor will start turning the impeller blade in the PVC pipe.^{[11]XResearch source}
Warning: Always connect the red wire first, and then the black wire so you don’t shock yourself.
6
Place the end of the pipe across from the motor into water to pump it. Once the pump has power from the battery, stick the end of the PVC pipe with the impeller blade into a body of water. The pressure created by the blade will pull the water out and push it through the run opening of the tee socket. Hold the pump in the water for as long as you want to pump it out.^{[12]XResearch source}
- Use a small swimming pool or a bucket of water to test out your pump.
- Do not submerge the motor.
- Disconnect the black wire first, then the red wire to deactivate the pump.

Community Q&A

Search

Add New Question

Question
Is it wrong to put the motor in the water?
Ssongsammy
Community Answer
Yes. A motor may be spoilt, burn or even shock you if put in water. In order to stay safe, don't do that at all. However, if you want to use a pump under water, DIY is not an easy option.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 6
Question
Can we connect the power in our regular home socket or is it necessary to have a 12v battery? Are there any differences?
Tinkerer02
Top Answerer
Connecting to a regular home socket is very dangerous - water will conduct electricity! The 120Vac or 240Vac is high enough to kill you. Since water will allow enough current to flow to be deadly, you don't have to touch the wire that is in the water, just touching the water will be deadly. Of course, there are appliances that are meant to work under water, they have special seals that prevent water from getting inside or they are totally glued shut. Stick with 12v for underwater projects, which a is low enough voltage that will not kill you when it is wet.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 4

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Always connect the positive wire first, then the negative. When you’re disconnecting them, always remove the negative wire, then the positive.
Thanks
Helpful2 Not Helpful1
Soldering irons are extremely hot. Be careful not to burn yourself when you’re using it and be sure not to place it down on a flammable surface while it’s still hot.
Thanks
Helpful1 Not Helpful0