How to Stop a Bicycle Rim from Wobbling

Download Article

A guide to truing your bicycle wheel

Download Article

Fixing Lateral Wobbling

|

Fixing Radial Wobbling

|

Troubleshooting

|

Q&A

The best way to make sure a bicycle rim stops wobbling is through using a method called "truing" the wheel. The spokes on your bike all work together to keep the rim straight, each one pulling in a slightly different direction at the same force in order to keep the wheel straight. Because there are so many spokes to account for, this makes truing a tricky art form. But, if you're patient and go slowly, it is still very doable for any burgeoning bike mechanic.

Things You Should Know

Flip the bike upside down, or put the wobbly wheel in a truing stand. Then, locate the bend in the rim by noting where the wheel comes nearer to the brakes.
Grip the spokes around your problem area and squeeze lightly, checking for looseness. Then, use your spoke wrench to tighten the "nipple" with a half-turn clockwise.
Keep adjusting the nipples using the 3-spoke adjustment process until the wobble is gone.

Method 1

Method 1 of 3:

Fixing a Lateral (Side to Side) Wobble

Download Article

1
Flip the bike upside down, or put the wobbly wheel in a truing stand if you have one. You need to be able to spin the wheel freely, allowing you to see where it wobbles and make subtle changes. Usually, turning the bike upside down is more than enough, but precise mechanics can use a truing stand, which holds the wheel in place and has small calipers that let you notice even the smallest wobble.
- If you've got a serious wobble or issue, it can help to take the tire off first. At the very least, take some air out of the tires. If not, one will likely pop while you work.^{[1]XResearch source}
2
Locate the bend in the rim by noting where the wheel comes nearer to the brakes. Spin the wheel, watching near the brakes to see where the wheel swings to either side. Either stop the bike at this point with your fingers, noting where it is, or use a permanent marker to measure the wobble. Simply hold the marker evenly at one height, and spin the wheel so that any wobbling hits the marker and makes a streak.
- Looking to protect your beautiful wheels from marks? Take a small piece of masking tape and use it to make the spots where there is some wobble.
Advertisement
The way you tighten spokes seems a little counter-intuitive at first, since you'll be turning spokes on both the top and bottom of the wheel. It seems like it's breaking the "righty-tighty" rule you've grown up with, but there is an easier way to think about it. Imagine you're looking straight down at the top of the spoke where it meets the rim. If you were to take a screwdriver and stick it into the top of the spoke, you would turn the spoke clockwise, like normal, to tighten it, and counter-clockwise to loosen it. If you're ever in doubt, imagine which direction you would turn this screwdriver, and turn accordingly.
4
Grip the spokes around your problem area and squeeze lightly, checking for looseness. If you're not sure what "loose" is, feel your other wheel or the spokes on other sides of the wheel. While not all wobbly wheels have noticeably loose spokes, most do, which will point out the exact spoke where there is an issue. If a spoke is extremely loose, tighten it until it is about the same tension as those around it.
- If a spoke is extremely loose, you should still go ahead and try to fix it. That said, you may need a new rim if this happens regularly-- it should be a rare occurrence.^{[2]XResearch source}
- There are rare cases where a spoke feels too tense, which can cause a wobble as well. The technique to fix it (shown below) is the exact same, just with loosening instead of tightening.
5
Note which side each spoke pulls towards to find the ones causing your wobble. The spokes will alternate which side of the rim they go to -- half to the left, half to the right. The balance between these two sides is what keeps your wheel true and prevents wobble. So, if your wheel wobbles to the left, that means the spokes on the right side are too loose to keep things balanced, or the spokes on the left are too tight. This is why you only get wobbles in certain areas -- one spoke that is too loose only affects the wheel in the precise spot.
- Trace the spoke down from the rim down to the center of the wheel to see which side it pulls towards.^{[3]XResearch source}
6
Tighten the spoke just below your problem area with a half-turn of the nipple. The golden rule of rim truing is go slow. Using your spoke wrench, a small tool with notches made to fit perfectly around the "nipple," the small sheath where the spoke meets the rim. Tighten it with a half-turn clockwise, then check again. Remember -- go slowly! This first turn won't fix the issue immediately, but don't keep turning just yet.
- Don't have a spoke wrench? A pair of needle-nose pliers will work in a pinch, but you should buy a spoke wrench cheaply as soon as you can.
- Remember to get the right side! If the wobble is to the left, you need to tighten the spoke that pulls the rim back to the right.^{[4]XResearch source}
7
Loosen the two spokes next to the one you just tightened, using only quarter-turns. This is how you keep the radial tension (up and down the rim, keeping it perfectly round) even without too much work. Say you just tightened a spoke on the right side of the rim, because it wobbled to the left. On either side of this spoke are two more spokes for the left side of the rim. Instead of continuing to crank on the right side, which can put too much pressure on one spoke, just loosen the spokes that pull it to the left. By using just a quarter turn on each spoke, you undo the same amount of tension on the left that you just added to the right, further balancing your wheel.
- Keep this simple math equation in your head as you work -- "if I tighten one spoke, I need to loosen the two spokes next to it half as much to make sure it stays balanced." The opposite equation, loosening one spoke and then tightening the other two half as much, also applies.
After every set of adjustments, spin the wheel and check your work. You should be keeping an eye on the wheel frequently -- don't just blindly tighten the spokes without seeing if you're making any progress.
9
Continue this 3-spoke adjustment process until the wobble is gone. You may need to take another set of three spokes and do the same thing. Just remember to keep the forces even, balancing out every adjustment on both sides. Never turn more than a half-turn at a time, and only work on one set of spokes at a time, allowing you to quickly undo something if you make a mistake.
- You will likely get smaller and smaller adjustments as you work -- using only turning the nipple by small increments. At this point, you should be spinning the wheel after every tightening, making only the smallest adjustments until you hit perfection.^{[5]XResearch source}
The most common issue is when the rim wobbles left to right, but bike tires can also wobble up and down as well, forming egg-shaped wheels or small flat spots where the tension isn't quite right up and down. After fixing the rim from side to side, make sure you didn't accidentally pull the wheel out of radial true as well. Usually, you'll have a few simple adjustments to make, but they should be easy.^{[6]XResearch source}

Method 2

Method 2 of 3:

Fixing Radial (Up and Down) Wobbling

Download Article

You'll always want to finish laterally truing the bike before attacking a radial wobble. Radial wobbling is when the bicycle rim loses its perfectly round shape, and you can usually feel a little bump when riding. This has more to do with the overall tension on the bike and is easier to fix once you've got side-to-side areas ironed out.
Spin the bike and place your finger, a marker, or a set of calipers underneath the wheel, just below where it would touch the tire. Then spin the wheel and note where it rubs against the caliper. This is where the rim has elongated, and you'll need to pull it in to get this bump out of the rim.^{[7]XResearch source}
One of these spokes will go to the right side of the bike, the other to the left, so tightening them both equally will pull the high spot in without ruing your radial truing.
4
Move the calipers, pen, or your finger closer in, spin the wheel, and adjust as needed. Keep working these two spokes until you've pulled the rub out of the rim, using smaller and smaller are turns (like a quarter-turn) to get more precise truing.
- After every set of turns, spin the wheel and double-check the lateral truing again, making sure you've not introduced a new wobble.^{[8]XResearch source}
This often happens on the opposite side of the wheel as the part you're working on, but it is an easy fix. Just find the two spokes on either side of your low spot and loosen them with quarter turns until you're even again.^{[9]XResearch source}

Method 3

Method 3 of 3:

Troubleshooting

Download Article

If your wheel can't stay in true, shows noticeable bending or denting, or your spokes won't stay tight, you'll need a new wheel. Oftentimes you'll need to true a wheel after a crash, which can loosen spokes, but it is not always possible. If you find yourself working and working without results, the rim is likely shot.^{[10]XResearch source}
The half-turn, two quarter-turn system won't work if the spoke is noticeably looser than the rest. Simply tighten this spoke on its own until it feels about as tight as the spokes around it, then move on to the more precise adjustments.
Is the rim really out of true, or do you not have the wheel in the frame properly? The best way to ensure this is to release the wheel as if you were about to take it off the bike. Then squeeze the brakes to hold the bike in the center of the frame. Re-tighten the wheel into the frame and then let go of the brakes, leaving the wheel in the dead center.
When you lose a spoke, you can keep riding for a bit if you have not other option to get home. But the increased pressure on the other spokes will warp and bend your wheel if left for too long, eventually causing more spokes to break and potentially ruining your rim permanently.^{[11]XResearch source}

Community Q&A

Search

Add New Question

Question
On a 2009 Rincon Giant, how do I assemble the gear cable to the derailure?
Munko Jensen
Community Answer
The clamp screw can fit over the cable. Then screw the cable down, clamping the cable.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 2

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

You will be making adjustments across a number of spokes. You cannot make the rim straight by cranking on one spoke.
Thanks
Helpful8 Not Helpful2
Make sure you use the correct size spoke wrench. They can be purchased at most bike shops. If you get the wrong size, the nipple may round off and you will not be able to true well.
Thanks
Helpful3 Not Helpful1
Make these adjustments in small increments, quarter turns on the spoke nipple.
Thanks
Helpful5 Not Helpful4

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Take care! It's easy to make your wheels more out of true (out of alignment) than they were originally if you move too quickly.
Thanks
Helpful4 Not Helpful0
When using a spoke wrench, remember to turn the wrench the opposite direction from normal. To tighten, turn left! To loosen, turn right! This is because you're working from the underside of the screw.
Thanks
Helpful1 Not Helpful2