How to Replace Road Bike Brakes

A road bike is a lightweight type of bicycle best for riding and racing on paved surfaces. However, like all bikes, they’ll eventually need new brake pads as the old ones wear out over time. Luckily, swapping out brake pads is simple on most road bikes. They use a rim brake system, and many have a quick-release mechanism to get the old pads out and the new ones in within just a few minutes. With the right tools and tips, you should be on your way again in no time!

Part 1

Part 1 of 3:

Removing the Old Pads

Download Article

1
Hit the quick-release lever on the brake calipers to widen them. Most road bikes have a quick-release lever on the brakes for easy changing. Look for a lever on each brake housing. Push this lever up to open the brakes and make them easier to work on.^{[1]XResearch source}
- If the bike doesn’t have a quick-release, look on the side of the calipers for an adjustment knob. Turn the knob counterclockwise to widen the brake pads as much as you can.
- Also hit the quick-release lever if you remove the bike wheel so there’s room to take the wheel off.
2
Take off the wheel if you don’t have enough room to work on the brakes. Road bikes are usually designed so you don’t have to take the whole wheel off to change the brake pads. If you hit the quick-release and the pads are still too close to the wheel frame, or there is no quick-release lever, then you’ll have to remove the wheel. Most wheels have a quick-release lever on the axle, so push this up to release the wheel. Then pop the wheel out of the axle.^{[2]XResearch source}
- If the bike doesn’t have a quick-release for the wheel, then use a wrench and unscrew the nut on the axle. Then slide the bolt out and remove the wheel.
Advertisement
3
Unscrew the retaining screw on the brake shoe to loosen the brake pad. The brake shoe is the platform that the pad attaches to, and it has 2 screws. The larger one holds the brake shoe in place, and the smaller one secures the brake pad. Take an Allen key and turn the smaller, retaining screw counterclockwise to loosen it. You can remove the screw entirely, or unscrew it about 75% to free the brake pad.^{[3]XResearch source}
- The size of the Allen key might vary, but 2 mm is a common size for bike brakes.
- If you do remove the screw, keep track of it so you don’t lose it. You’ll need it to put the new brake pad on.
4
Slide the brake pad backwards out of the shoe. With the screw loosened, the brake pads will slide out of position. Push the pad from the front and pull it out through the back of the shoe.^{[4]XResearch source}
- If the pad is stuck, try pulling it with a pair of pliers or pushing it with a screwdriver.
- If you still can’t get the pad out, then you might have to loosen the screw more or take it out entirely.

Part 2

Part 2 of 3:

Installing New Pads

Download Article

1
Get new brake pads made of a strong material. Generally, the size for bike brake pads is universal, so the main difference is which material you'll use. You have several choices, so pick the one that suits your needs.^{[5]XResearch source}
- Cheaper bike pads are made of resin. These will work fine but wear out quickly.
- Metal brake pads tend to not stop the bike as well, but they last much longer and work just as well in wet or rainy weather.
- Ceramic brakes usually perform very well. However, their shape could warp over time.
- If you need any guidance, ask an employee at a bike shop for help.
2
Point the new brake pad forward so it faces the right direction. Brake pads usually have an “R” or “L” on them to indicate which side of the bike they go on, as well as an arrow to show which direction is the front. Check for these markings and hold the brake pad so it’s facing the right direction.^{[6]XResearch source}
- The brake pad should be parallel to the tire rim.^{[7]XExpert SourceJonas Jackel
  Owner, Huckleberry BicyclesExpert Interview. 18 February 2020.}
3
Slide the new pad into the caliper. Insert the pad into the back of the brake shoe and push it forward. Slide the pad until it’s completely in the shoe.^{[8]XResearch source}
- You might hit some resistance as you insert the pad further. You can use pliers or a screwdriver to help get the pad in position.
- If you have a lot of trouble getting the pad into position, double check the pad markings to make sure it’s facing the right direction.
4
Tighten the retaining screw on the caliper. When the pad is all the way in, the retaining screw should go back in easily. Use the same Allen key and turn the screw clockwise to tighten it. Continue turning until the screw is all the way in.^{[9]XResearch source}
- If the screw won’t go in all the way, you may not have slid the pad in enough. Try pushing it some more to get it into the right position.
5
Repeat the process for the 3 other brake pads. Since bikes have 4 brake pads total, you’ll have to repeat this process 3 more times. The second brake pad is on the other side of the caliper, directly across from the first one you replaced. The other 2 are on the other wheel in the same spot. This should only take a few more minutes, so follow the same procedure to get your bike brakes up and running.
- If you had to remove the wheel, then you’ll have to also adjust the new brake pads.

Part 3

Part 3 of 3:

Adjusting the Pads

Download Article

1
Put the wheel back on if you removed it. Take the bike wheel and sit it back into the axle. Then push down the quick-release lever to lock it back in place. If you don't close the calipers, your brakes may not work properly.^{[10]XExpert SourceJonas Jackel
Owner, Huckleberry BicyclesExpert Interview. 18 February 2020.}
- If the bike doesn’t have a quick-release lever, then slide the bolt back into the axle and tighten the nut around it to lock the wheel in place.^{[11]XResearch source}
- If you didn’t remove the wheel, you probably don’t have to adjust the brake pads.
- Be sure the wheel is seated all the way into the frame. Otherwise, your brakes won't line up properly.^{[12]XExpert SourceJonas Jackel
  Owner, Huckleberry BicyclesExpert Interview. 18 February 2020.}
2
Release the brake shoes by loosening the larger retaining screw. The larger retaining screw secures the brake shoe. Unscrew it with an Allen key until the shoe loosens enough to move up and down.^{[13]XResearch source}
- You’ll need a larger Allen key than the one you used to remove the brake pad. Test a few to make sure you have the right size.
- Don’t remove that screw completely or the brake shoe will fall off.
- If you also have to replace the brake shoes, you can undo this screw entirely to take the shoe off. Then screw the new shoe into this slot.
3
Slide the brake pads so they’re aligned over the wheel rim. With the brake shoe loose, you can slide it up and down. Adjust the shoe so the pad is aligned perfectly over the wheel rim, where it’s supposed to touch. Also make sure the shoe is straight and that no parts of it touch the bike tire.^{[14]XResearch source}
- If the pad touches the tire, not only will the bike not stop properly, but the tire could pop. Make sure no part of the pad or shoe touches the tire at all, even when you're pressing the brakes down.
Once the pad is in the right position, get your Allen key again. Tighten the screw by turning it clockwise. This locks the shoe in place.^{[15]XResearch source}
5
Turn the adjustment knob so the pads rest ¹⁄₈ in (0.32 cm) from the rim. Look on the side of the brake calipers for a knob. This opens and closes the brake pads. Once you’ve adjusted both brake pads on the caliper, turn the knob clockwise to tighten them. Adjust them so they rest about ¹⁄₈ in (0.32 cm) from the bike rim. This leaves enough space so the pads won’t grind, but it’s close enough so you can still stop well.^{[16]XResearch source}
- This is a standard distance, but you can adjust this if you want more or less sensitivity on your brakes.
- It’s important to make sure the pads don’t touch the rim unless you’re pressing the brakes. Otherwise, the pads will grind and wear out quickly. If you hear any noise while the wheels are spinning, the pads may be touching the rim.
6
Test the brakes to make sure they stop the wheels. Replacing your brakes improperly can be dangerous, so always check your work when you're done. First go over all the screws you loosened and make sure they're nice and tight.^{[17]XResearch source} Then lift up the front of the bike and spin the wheel. Hit the brake to make sure the wheel stops all the way. Do the same with the rear wheel to confirm that the brakes are working properly.
- Never try to ride the bike if the wheels aren't stopping properly. Take the bike to a specialist for repairs.

Expert Q&A

Search

Add New Question

Question
What are some mistakes to avoid when I'm changing my bike brakes?
Jonas Jackel
Owner, Huckleberry Bicycles
Jonas Jackel is the Owner of Huckleberry Bicycles, a bicycle retail store based in San Francisco, California. Jonas has over 20 years of experience managing bicycle retail stores and has operated Huckleberry Bicycles since 2011. Huckleberry Bicycles specializes in servicing, repairing, and custom building road, cross, gravel, touring, folding, and e-bikes. Jonas was also previously sat on the Board of Directors for Bike East Bay, a bicycle-advocacy non-profit organization based in Oakland, California.
Jonas Jackel
Owner, Huckleberry Bicycles
Expert Answer
Some common mistakes include not having the brake pad parallel to the rim, or not having the wheel installed properly on the bike. Also, if the quick release on your brakes are like calipers, make sure they're closed, or your brakes may feel like they need to be adjusted.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 3
Question
How do I replace disc brakes on a bicycle?
Community Answer
Find a brake handle and look over the connection. Remove the disc brake with a screwdriver. Buy a disc brake in a bicycle repair shop. Screw it on the bike with a screwdriver.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Things You’ll Need

New brake pads
Allen keys
Pliers or screwdriver

Tips

You might get some grease on your hands while you’re replacing your brakes. Be ready to wash your hands or wear gloves.
Thanks
Helpful1 Not Helpful0
Most road bikes use rim brakes, but you can also fix disc brakes if your bike uses these.
Thanks
Helpful1 Not Helpful0
You can also change the brake cable if you have to.
Thanks
Helpful1 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Whenever you ride for the first time after working on your brakes, start slow and test them out. If you made a mistake on your brakes, you could get hurt while riding at top speed.
Thanks
Helpful1 Not Helpful0
Your brakes are an important part of your bike and need to be a top shape. If you aren’t sure how to replace brakes properly, take the bike to a professional to make sure it’s done right.
Thanks
Helpful1 Not Helpful3