This article was co-authored by Nitzan Levy. Captain Nitzan Levy is a Sailor, Social Entrepreneur, and the Founder of Sailors NYC, a recreational sailors’ club based in Jersey City, New Jersey that specializes in cruising boats and a variety of community programs. Capt. Levy has over 20 years of sailing experience and has sailed in many places around the world including: the Atlantic Ocean, the Mediterranean Sea, The Caribbean, and the Indian Ocean. Capt. Levy is a U.S. Coast Guard Licensed Master of vessels up to 50 Tons with Auxiliary Sail and Assistance Towing Endorsements. Capt. Levy is also a NauticEd Level V Captain Rank Chief Instructor, an American National Standards Assessor, an SLC instructor, an ASA (American Sailing Association) Certified Instructor Bareboat Chartering, and an Israeli licensed skipper on Boats for International Voyages.
There are 9 references cited in this article, which can be found at the bottom of the page.
This article has been viewed 161,775 times.
Flushing a boat motor by running it out of water is a routine maintenance task. Running the engine without a water source for any length of time will cause damage, so you’ll need to attach a hose to the motor’s water intakes. Some newer motors have built-in attachments that accept a hose nozzle. If your motor doesn’t, you’ll need a set of motor flusher muffs. Turn on the water before starting the engine, then run it for 5 to 10 minutes or according to the manufacturer’s recommendations.
Steps
Read your manual before starting the motor out of water. Check the manual to find out where your intakes are located and whether they have built-in attachments for a garden hose. If not, you’ll need a set of motor muffs.[1]- Most manufacturers’ recommendations for flushing or running a motor out of water are similar. However, you should still check the specific procedure for your model.
Screw the hose directly into the motor if it has a built-in attachment. With the engine lowered into the vertical position (not tilted in the tow position), locate the water intakes on the sides of the lower unit. Screw the hose nozzle into one of the intakes. Your manual will most likely recommend covering the other intake with heavy tape.[2]Advertisement
Purchase motor muffs at a boating store or online. If you need motor muffs, you can purchase a set for under $10 (USD) at a marina, sporting goods store, or online. They look like earmuffs connected by a long, V-shaped rod.
Wet the muffs to get a better seal. Many boat owners like to splash the insides of the muffs with water before attaching them to the motor. A better seal can help prevent the muffs from sliding off while the engine’s running.[3]
Clamp the muffs to the motor and stay clear of the propeller. Slide the muffs onto the motor’s lower unit so they’re aligned over the water intakes. Be sure to position the muffs so the connecting rod is located in front of the motor on the opposite side of the propeller.[4]- While you should keep the engine in neutral while running it out of water, you still need to be careful around the propeller. Injury or damage will result if the engine accidentally slips into gear and the connecting rod is on the propeller side of the motor.
Screw the garden hose onto the muffs. One of the muffs has a nozzle, and the other is solid. Find the one with the nozzle, then screw your garden hose into it. Double check that the connection is tight and that the muffs fit snugly over the motor’s water intakes.
Turn on the water. After attaching the garden hose, head to the faucet and turn on the water. Check your manual to see if it specifies a water pressure setting. Many manufacturers recommend setting it to about half pressure.[5]- Do not start the engine before turning on the water.
Put the engine in neutral. Make sure the gearshift or throttle is in the neutral position. The engine needs to be in neutral to start and should stay in neutral while you run it.[6]- If you need to put the engine in gear to test the propeller's function, use caution and make sure no people or objects go near the moving propeller.
Start the engine. Depending on your engine type, insert the key or pull the starter to engage the engine. For some electric engines, you’ll also need to push and release a button after turning the key.[7]
Make sure the motor’s water pump is working. You should see a stream of water flowing out of the top of the motor. If there’s no overflow stream, there’s something wrong with your water pump.[8]- If there’s no stream, turn off the engine immediately. Insert a thin wire into the outflow tube to check for debris. Start the engine again to see if that solved the problem. If there’s still no outflow, you will likely need to have a mechanic replace your water pump.[9]
Run the engine for 10 minutes, or according to the manual’s instructions. If you’re flushing the motor, most manufacturers recommend running it for 5 to 10 minutes. If you’re running the engine for another purpose, such as to test its function, run it for as long as your maintenance task requires.- Don’t run the engine unattended. Keep an eye on the muffs and make sure they don’t slip off of the water intakes.[10]
- Regardless of your task, it’s unlikely that you’ll need to run it more than 10 to 15 minutes.
Turn off the engine before turning off the water. After about 10 minutes, turn the key or close the throttle to turn off the engine. Turn off the water only after disengaging the engine. Running the engine without a water source for just a moment could cause damage.[11]
Unscrew the hose from the muffs or built-in attachment. After turning off the water, remove the garden hose from the muffs or motor’s water intake, coil it up, and put it away.[12]
Remove the muffs if you’re using them. If necessary, slide the muffs off of the motor’s lower unit. Store them in your boat house, garage, or other handy spot so you can flush your motor after your next outing.[13]
Let water drain before tilting the engine. Keep the engine down for 30 to 60 minutes so water drains from the powerhead. After letting it drain, lift the motor into the tilted position. Cover the boat and tow it into your garage or boat house, or store it as you prefer.[14]
Community Q&A
- QuestionI have the water on and it does not come out where it is supposed to. Where is the water going?
Community AnswerYour motor will have to warm up before the thermostat opens up to allow water to cool your engine. After you run it for a while it should begin to come out. Give it some time. If your motor runs for a minute or more, you may need a new impeller. - QuestionIs water supposed to come out the propeller when the muffs are attached, water on, motor running?
Aloha27Community AnswerYes. As a matter of fact, most of the cooling water exits through the prop. The "pee hole" is just a visual aid for the operator to ensure that cooling water is being circulated. - QuestionIf the motor ran for 5 to 10 minutes without water going through it what kind of damage would it cause?
NathanCommunity AnswerIt is not certain within that timeframe but running the motor without a garden hose or some type of water source can result in overheating.
Tips
- Flush your motor after every outing to prevent salt, silt, and other debris from accumulating.Thanks
Things You’ll Need
- Boat trailer
- Garden hose
- Motor flusher muffs (optional)
- Duct tape (optional)
References
- ↑ https://www.boatus.com/magazine/2013/August/outboard-flushing-the-right-way.asp
- ↑ https://www.boatus.com/magazine/2013/August/outboard-flushing-the-right-way.asp
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=100
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=82
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=107
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=123
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=129
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=132
- ↑ https://www.boatsafe.com/nauticalknowhow/outboard.htm
- ↑ https://www.boatus.com/magazine/2013/August/outboard-flushing-the-right-way.asp
- ↑ https://www.boats.com/reviews/outboard-expert-lay-up-goofs/#.WnNYvqinGCg
- ↑ https://www.boatus.com/magazine/2013/August/outboard-flushing-the-right-way.asp
- ↑ https://www.youtube.com/watch?v=e9fZ5ykTne4&feature=youtu.be&list=UUX5uNpKyy9TU6f1tkCYn0LA&t=129
- ↑ https://www.boatus.com/magazine/2013/August/outboard-flushing-the-right-way.asp
About This Article
To run your boat motor out of water, start by attaching a hose to your motor’s water intake so you can flush in water, which will avoid damaging the engine. Once the hose is attached, turn on the water faucet. Then, pull the gear shift to neutral and start the engine. Make sure there’s a stream of water flowing out of the top of the motor, which means the water pump is working correctly. If you don’t see a stream, turn off the engine immediately and fix the water pump before restarting it. Once your engine is on, run the boat for 5-10 minutes to flush it out, then turn off the engine before turning off the water. For more advice on attaching a hose to your motor’s water intake, read on!
Reader Success Stories
"I bought a 1973 30 ft pontoon with inboard 350 Mercruiser. This boat has been sitting in storage for 11 years, I don't have a manual but this article helped me with everything I needed."..." more
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
