How to Restore a Whiteboard

Don't throw old whiteboards away. This article describes how to restore dry erase whiteboards that have become hard to erase and/or require constant cleaning. While it's very difficult to get the board back to perfection, you'll be writing and erasing beautifully in no time.

Method 1

Method 1 of 2:

Complete Restoring the Board

Download Article

A lot of cleaning problems actually start with a dirty eraser. Be sure to beat them out, and take a vacuum hose to it as well to get as much dust out as possible. Your eraser will suddenly be much more effective.^{[1]XResearch source}
Get off as much as you can using this method, but don't sweat it if there are still marks.^{[2]XResearch source} You simply want to get as much off as possible.
Advertisement
3
Clean the whiteboard with a whiteboard cleaner and paper towel. If you can't get ahold of whiteboard cleaner, just use a damp cloth.^{[3]XResearch source} Don't substitute in other cleaners, as many of them will simply strip off more of the essential coating that allows you to erase the markers.
- Keep wiping down the board with your clean towel until it no longer picks up dirt and dust.
- Always use gentle, soft towels or paper towels. Never use abrasive pads or scrubbers!
WD-40 is a light oil that will keep the board slick. This allows you to write on it without the ink drying into the board and leaving permanent marks. While it may make the board a bit slippery, it will be usable.^{[4]XResearch source}
Revive a neglected board. "After years of ghost marks, my classroom whiteboard was a mess. Following the cleaning steps here involving baking soda, alcohol, and elbow grease, I revived it beautifully. The process took effort, but the sparkling results were worth it!" - Thisya Shashidhara (How.com.vn Community Member)
Try manufacturer-approved solutions with confidence. "I was wary of "quick fix" internet tips. But learning the WD-40 method was actually recommended by whiteboard makers reassured me. Now, I could revive my board without worries about causing harm long-term." - Jain N.
Make old boards work like new ones. "My classroom's worn whiteboards were discolored and ghosting badly. The tips here on deep cleaning and applying WD-40 made them work like new! I never considered WD-40 before — it was a game-changer." - Ken M.
Restore a well-worn board. "At work, our shared whiteboard was ghosting and stained from years of use. Following this advice brought it back to life! The step-by-step instructions gave me the confidence to tackle even a very worn board. Our board looks fresh again." - Rebecca W.
Did you know that How.com.vn has collected over 365,000 reader stories since it started in 2005? We’d love to hear from you! Share your story here.
When done, dry everything with a paper towel. The board should feel a little slick with the oil, but it should not be pooling up anywhere or visible.^{[5]XResearch source} Wipe in a circular motion to ensure the whole board is evenly coated.
Make a few marks with a dry erase maker, then wait 10-15 minutes before trying to erase. If you did it all successfully, and the board isn't beyond repair, the marker should wipe off easily even after all of this time to dry.

Method 2

Method 2 of 2:

Keeping the Board Clean

Download Article

1
Never use abrasive or scratching motions to clean a whiteboard. The non-porousness of the board is what allows the ink to come off easily, as a clean, Teflon-like coating protects the board from letting ink set in.^{[6]XResearch source} But scratches and "tears" in this coating will allow the ink to seep through, ruining your board permanently. Always use soft, clean towels and rags.
- Adhesives like tape and glue will also rip up the coating when removed.
2
Use whiteboard cleaner and a dry towel at the end of every week to keep the board clean. Regular cleanings will be essential to prevent the need to restore the board in the first place. A light spray of cleaner and a towel will remove marks before the set in, keeping your board beautiful for years to come.
- Any marker left on for more than 24 hours is at risk to leave "ghost" marks.
- Very stubborn stains can be removed with a little propyl alcohol. Or, you can prepare a mixture that is 50 percent tap water and 50 percent isopropyl rubbing alcohol. Wipe the whiteboard, then dry it off with a clean cloth to remove alcohol remnants—don't let alcohol dry on the board.^{[7]XResearch source}
3
Remove "ghost marks" or permanent marker by completely covering the board in black dry-erase marker, then erasing it quickly The wet marker actually has chemicals that keep the ink fluid, which will temporarily loosen the ghost marks or permanent marker. Work quickly, then erase with a dry, clean eraser to get most of these marks off.
- Note, if you work too slowly you may dry the black marker on there, completely defeating the purpose!
- You can also use this method to spot clean certain marks. Just make sure they are completely covered with ink before erasing.^{[8]XResearch source}
4
Never use degreasers, soap, or cleaners not specifically formulated for dry-erase boards. Most soaps break up oils and sheens that are not water-soluble, helping cut through tough stains and chemicals. But the sheen on a whiteboard is there on purpose, allowing the markers to write without ever truly drying out. Never use a cleaner that isn't made to specifically work with your white board.
- In a pinch, denatured alcohol can work as a more powerful cleaner than water, and it shouldn't harm whatever original finish you have left.
Don't let the board air dry. If you're wiping the board down at the end of the day, take a paper towel and clean rag and dry it as well. This will help protect the longevity of the board.
Blot it on a kitchen towel. If you need to wash it, dampen a soft cloth and run over it to remove traces of ink, but do not wet it. You want to start with as little dust and debris as possible to keep the board clean and smooth.
7
Know that restoration will only work so many times before you need a new board. If someone has ruined the finish with a heavy cleaner, or you find that you have to add WD-40 more and more frequently, you'll likely hit the end of the line with your board. While you can try to resurface it again, you'll likely be best off with a new, factory sprayed finish.
- WD-40 will make the board usable again, but it may also lead to slightly streaky writing. It is nothing that makes the board unusable, but it should be noted.

Community Q&A

Search

Add New Question

Question
How long does a dry erase board last?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
This depends on the quality of the board and its construction, so it can vary widely. Plastic boards will probably last from 1-5 years, while more durable and better constructed boards can last from 10-20 years or even longer. Your best bet is to figure out what type of board you have and see how many years the manufacturer's warranty or guarantee covers.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 7 Helpful 8
Question
How do you get permanent marker off a whiteboard?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
The easiest way is to draw over the permanent marker with a dry-erase marker and then erase both of them.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 7
Question
What is the best way to clean a whiteboard?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
High percentage isopropyl alcohol will usually do the job, but many cleaners are effective. Check out How to Erase Old Marks off a Dry Erase Board for other options.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 3

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

The WD-40 fills in the dried pores of the whiteboard which were holding in the ink and makes it easier to erase it.
Thanks
Helpful3 Not Helpful0
The commercial cleaner/restorer you can purchase from the manufacturer of the whiteboard is similar to car wax.
Thanks
Helpful4 Not Helpful1
If there are any old marks on the board then you can go over it in a new pen and erase it with a dry eraser, this will wipe it away.
Thanks
Helpful1 Not Helpful1