How to Replace a Lamp Switch

Lamps are a stylish way to bring soft light into a room, but it can be frustrating when your lamp switch stops working. Instead of throwing your lamp away, try installing a new light switch yourself! It’s an easy project that even a beginner can tackle, and you can replace the switch whether it’s located on the lamp itself or on the cord. All you need are a few simple tools and you’ll be out of the dark in no time!

Method 1

Method 1 of 2:

Replacing a Socket Switch

Download Article

1
Purchase a new socket switch from a hardware store. Your new switch can be whatever type you prefer, regardless of the existing switch. For instance, if your lamp has a pull chain but you want to install a 3-way turn knob, all you have to do is buy a 3-way turn switch and a light bulb with 2 brightness levels.^{[1]XResearch source}
- You can even replace a socket switch with a cord switch. Just purchase a new socket assembly without a switch and follow the instructions for replacing a cord switch.
- You can buy a new socket switch from most hardware stores, and they usually cost around $2-$5 USD.
Never take chances when you’re working with electricity. Double-check to be sure that the lamp is unplugged before you start to take it apart.
Advertisement
At this point, the socket at the top of the lamp should be exposed. On most lamps, this is where the switch is located.
4
Squeeze and pull the socket shell to remove it from the lamp. The socket shell is the actual assembly where the switch is located and the light bulb screws in. On most lamps, you can squeeze the socket shell and pull upwards to remove it.^{[2]XResearch source}
- If the socket shell is hard to remove, use a screwdriver to pry it loose.
5
Locate the wires attached to the socket shell. There should be 2 wires attached to the switch. 1 is hot and the other is neutral. The hot wire is usually attached to a brass screw, and the neutral wire is usually attached to a silver screw.^{[3]XResearch source}
- The neutral wire is usually marked in some way. It may be a different color, or the insulation may be printed, stamped, or have indentations. Make sure to note this now, since you’ll need to know which wire is neutral when you hook up your new switch.
- If you can’t identify the neutral wire, look at the plug. The neutral wire is attached to the wider plug blade on a polarized plug. If your plug blades are the same size, you should replace the plug while you’re replacing the socket.^{[4]XResearch source}
Cut through the wires as close to the switch as possible to ensure you have plenty of wire to work with.^{[5]XResearch source}
7
Cut off the ends of the wire and strip away ¹⁄₂ inch (1.3 cm) of insulation. Wire cutters can also be used to strip insulation from wires. Use the wire cutters to make a notch in the insulation around the wires, then clamp down on the insulation with the strippers and carefully pull the insulation away.^{[6]XResearch source}
- If you see any strands of wire when you pull away the insulation, it means you cut too deep. Cut off that section and start again.
8
String the 2 wires through your socket and attach them to the screws. Use your fingers to wrap the wire tightly around the screw. Be sure to connect the neutral wire to the silver screw and the hot wire to the brass screw.
- Although sockets will be slightly different depending on the manufacturer, the wires should thread easily through the socket. Make sure the socket is right-side-up and look for wire channels to help you know where to guide the wire.
You should hear the new socket shell snap into place. If there is a screw on the stem of the lamp, tighten it now to hold the socket in place.
10
Replace the light bulb and lampshade and plug in the lamp. If you’ve done everything right, you should be able to use your new switch to turn on your lamp!
- If the lamp doesn't come on, check the connection in your switch and try again. If this doesn't help, you may need to replace the plug.

Method 2

Method 2 of 2:

Replacing a Cord Switch

Download Article

1
Look for printing on the lamp cord to determine the size switch you need. Look for printing which says either SPT-1 or SPT-2. The printing is small, so you might have to look carefully.^{[7]XResearch source}
- The difference between SPT-1 and SPT-2 involves the thickness of the lamp cord.
Some switches only require you to connect the hot wire. If this is the case, there will be a channel along one side of the switch for the neutral wire.
3
Remove the existing cord switch. You may be able to open the casing of the existing switch and remove the wires without cutting them, but if not, use wire cutters to cut as close to the switch as you can.^{[8]XResearch source}
- Try to avoid cutting the neutral wire. If you have to cut it in order to remove the old switch, strip the insulation and connect the cut ends of the neutral wire together. If you like, add a plastic connector to protect the wire at the location where you want your new switch to be.
- If you are adding a cord switch when there wasn’t one before, use a small knife to carefully split the cord where you want your new switch to go, then cut through the hot wire. If your switch requires you to attach the neutral wire, cut through that too.
Use your wire cutters to make a notch in the wire insulation, then gently pull to remove it. Only take off as much insulation as you need to attach the wires to the screws in the switch.^{[9]XResearch source}
If you only have one screw, it's for the hot wire. If you have to connect both the hot and neutral wires, the hot wire goes to the brass screw, and the neutral wire goes to the silver screw.
6
Insert the stripped wires into the screw terminals. Use your fingers to wrap the wires around the screws securely, and make sure there is enough insulation on the wires so that no live wires will be exposed when you close the switch.^{[10]XResearch source}
- There should be no visible wires showing when the switch is assembled. All you should see is insulated cord.
- If the exposed wires are too long, use the wire cutters to snip off a small portion and reattach the wires to the screws.
Make sure that the cover closes securely and there are no bare wires showing around the switch.^{[11]XResearch source}
8
Plug in your lamp and try out your new switch. If you’re confident that the switch feels like it’s securely connected and there are no live wires showing, it’s time to test out your lamp! If you hooked everything up right, you should be able to plug in the lamp and turn it right on.
- If the lamp doesn’t turn on, double-check your wiring and try again.

Expert Q&A

Search

Add New Question

Question
How do you change the switch in a ceiling fan?
Martin Hennum
Licensed Electrical Contractor
Martin Hennum is a Licensed Electrical Contractor and Owner of Peach Electric based in Sacramento, California. With over 10 years of experience, Martin and his team specialize in residential and commercial electrical work. They are knowledgeable about new technologies that help clients with future proofing so they save time and money. Martin is passionate about customer service, bringing the best information to clients, and prioritizing safety across projects.
Martin Hennum
Licensed Electrical Contractor
Expert Answer
First, take the trim cover off—which is the white cover plate. Then, take the switch out and identify which one has power using a non-contact voltage tester. Finally, put that on the correct terminal point on the new switch, screw it back in and install the trim cover back on.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0
Question
Can you fix a lamp switch?
Drew Hawkins1
Community Answer
You can definitely replace a socket switch if it isn't working anymore. Make sure the lamp is unplugged and remove the shade and bulb. The socket shell is the actual assembly where the switch is located and the light bulb screws in. On most lamps, you can squeeze the socket shell and pull upwards to remove it. If it's hard to remove, use a screwdriver to pry it loose. There should be 2 wires attached to the switch. 1 is hot and the other is neutral. The hot wire is usually attached to a brass screw, and the neutral wire is usually attached to a silver screw. Cut through the wires as close to the switch as possible to ensure you have plenty of wire to work with. Then, cut off the ends of the wire and strip away 1⁄2 inch (1.3 cm) of insulation with a pair of wire cutters. Then, use your fingers to wrap the 2 wires tightly around the screw and then push the new socket into the lamp. You can then replace the light bulb, plug in the lamp, and test it out.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 4 Helpful 4
Question
How do you a lamp cord switch?
Drew Hawkins1
Community Answer
It's actually not too difficult. If you're replacing the switch with a new one, you may not need to cut all of the wires. Some switches only require you to connect the hot wire. If this is the case, there will be a channel along one side of the switch for the neutral wire. You may even be able to open the casing of the existing switch and remove the wires without cutting them, but if not, use wire cutters to cut as close to the switch as you can. Try to avoid cutting the neutral wire. If you have to cut it in order to remove the old switch, strip the insulation and connect the cut ends of the neutral wire together. You can also add a plastic connector to protect the wire at the location where you want your new switch to be.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0