How to Check Earthing at Home

Earthing is a process similar to grounding that transfers discharged electricity from an appliance directly to the ground so you don’t get shocked if there’s a faulty wire. While the standard electrical code requires earthing on your system, older homes may not have earthing. If you want to check if you have proper earthing, try plugging the wires from a lightbulb base into the ports of an outlet to see if it lights up. If you want to test more accurately, use a multimeter to take your readings instead.

Method 1

Method 1 of 2:

Testing with a Lightbulb

Download Article

1
Screw a 100-watt bulb into a base socket. Look for a standard lightbulb that has a 100-watt output on it. Then check your local hardware store for a standalone base socket to screw your lightbulb into. Choose one that already has 2 wires attached to it so you don’t have to use your own. Position the end of the lightbulb inside the socket and rotate it clockwise to secure it to the base.^{[1]XResearch source}
- Make sure the socket base is made to use with 100-watt lightbulbs. If the power rating is too strong or weak, then the test may not work.
Find the matching gauge for the wire on the base using a pair of wire strippers. Clamp one of the wires in the slot so about ¹⁄₂ inch (1.3 cm) sticks out from the other side. Slowly pull the wire toward you to cut through the insulation and strip it so the wiring is exposed. Repeat the process for the second wire on the other side of the base.^{[2]XResearch source}
Tip: If you don’t have a wire stripper, pinch the end of the wire between the blades of a pair of scissors. Pull the wire in the opposite direction of the section you want to strip to remove the insulation. Be careful not to squeeze too hard or else you’ll cut through the wires.^{[3]XResearch source}
Advertisement
3
Push the wires on the base into the live and neutral ports of an outlet. Take either wire connected to the base and push the exposed end into the live port on your outlet, which is usually the smaller slot. Then take the second wire on the base and put it into the neutral slot, which is the larger port next to the live one. If your outlet is properly working, the lightbulb will immediately turn on.^{[4]XResearch source}
- The light won’t turn on if the outlet you’re testing isn’t connected to power.
Warning: Never hold a wire that’s exposed or has cracked insulation while it’s plugged in since you could shock or electrocute yourself.
4
Plug the wires into the live and earthing ports to see if the lightbulb turns on. Pull both wires out from their ports to begin. Take one of the wires and place it in the earthing port, which is the third hole at the top or bottom of your outlet. Place the second wire in the live port again to see if the lightbulb illuminates. If the lightbulb has the same intensity as your first test, then the outlet is properly earthed. If the light doesn’t come on at all, then the outlet doesn’t have any earthing.^{[5]XResearch source}
- If the light is dimmer than your first test, then your outlet has earthing on it, but it may be faulty. Contact an electrician to inspect your electrical system to find the source of the problem.

Method 2

Method 2 of 2:

Checking Earthing with a Multimeter

Download Article

1
Set a multimeter to measure AC voltage. Multimeters can test various electrical components for voltage, current, and resistance. If you’re using an analog multimeter, turn the dial on the front to the letter “V” that has wavy lines next to it for AC power. If you have a digital multimeter, cycle through the settings using the buttons until you reach AC voltage. Choose the highest cutoff value for the voltage on the meter so you can get an accurate reading.^{[6]XTrustworthy SourceScience BuddiesExpert-sourced database of science projects, explanations, and educational materialGo to source}
- You can buy multimeters online or from your local hardware store.
- Some multimeters may not have cutoff values listed on them. In that case, just switch the meter to the AC voltage setting and continue.
2
Plug the red and black leads into the matching ports on the multimeter. Your multimeter will have red and black leads that connect to the ports on the bottom of the machine. Attach the end of the red lead to the port labeled with “V”, “Ω,” or “+” and plug the black lead into the port labeled “COM” or “-” so you can check your outlet.^{[7]XTrustworthy SourceScience BuddiesExpert-sourced database of science projects, explanations, and educational materialGo to source}
- Avoid swapping the leads since you could cause the multimeter to short circuit.
Warning: Don’t use any leads that have cracks, damage, or exposed wires since you could get electrocuted while you’re testing your outlet.
3
Take a reading while the leads are in the live and neutral ports of an outlet. Hold the leads by the insulation wrapped around them so you don’t get shocked while you’re working. Push the pointed end of the red lead into the neutral port on the outlet, which is usually the smaller slot. Then put the end of the black lead into the live port, which is the larger and longer slot on your outlet. Check the voltage reading on the multimeter and write it down.^{[8]XTrustworthy SourceScience BuddiesExpert-sourced database of science projects, explanations, and educational materialGo to source}
- Start by testing your multimeter on an outlet that you know works so you can see what a normal reading looks like.
- The ports where you attach the leads may differ depending on the type of plug you’re using. For example, on a type D or M plug, the live port is on the bottom right while the neutral port is on the bottom left.
4
Check the voltage when the leads are inserted to the live and earthing ports. Take the red lead out from the neutral port and carefully place it inside the earthing port, which is either a circular or U-shaped hole on the top or bottom of the outlet. Check the reading on the multimeter to see how many volts travel between them. Write down the measurement so you can compare your readings.^{[9]XTrustworthy SourcePubMed CentralJournal archive from the U.S. National Institutes of HealthGo to source}
- If your home has earthing, then the reading should be the same as or within 5 volts of the first reading you took.
- If the reading between the live and earthing ports is close to 0, then you don’t have any earthing on that outlet.
- If your outlet doesn’t have an earthing port, then it isn’t connected and does not have earthing.
5
Test the voltage between the neutral and earthing ports on the outlet. Place the red lead in the neutral slot and the black lead into the earthing port to check the reading. The volts listed on the multimeter will be a small amount compared to the other readings you’ve taken. Write the third reading down so you know how much electricity is going between the ports.^{[11]XResearch sourcewww.usbr.gov/tsc/techreferences/mands/mands-pdfs/Trnsfrmr.pdf}
- You don’t need to test the neutral and earthing ports if you’ve already determined you don’t have earthing on the outlet.
6
Calculate the total leakage on your outlet to see if it's less than 2 V. The leakage is the number of volts that transfer from your earthing port to the outlet. Subtract the first reading you took (live to neutral) from the second (live to earthing). After solving that, add the number of volts from your third reading (neutral to earthing). If the number is greater than 2 V, then your earthing may be faulty. Otherwise, the outlet is safe to use.^{[11]XTrustworthy SourceU.S. Department of EnergyOfficial site for the U.S. Department of Energy, which provides resources related to energy safety, conservation, and efficiencyGo to source}
- For example, if your first reading was 230 V, the second reading was 231 V, and the third was 0.5 V, then your formula would be (231-230) + 0.5, which simplifies to 1.5 V.
- If you have faulty earthing, contact a licensed electrician to look at your electrical system to find the problem.

Expert Q&A

Search

Add New Question

Question
How do you know if your home has proper earthing?
Ricardo Mitchell
Electrician & Construction Professional, CN Coterie
Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience.
Ricardo Mitchell
Electrician & Construction Professional, CN Coterie
Expert Answer
This is more commonly called grounding and bonding. Look on the meter on the main in your building—there should be a grounding rod with a grounding wire, which will usually be green. This grounding wire prevents a shortage if there's any lightning or an electrical search. In an outlet, the grounding wire will either be a naked copper wire or a green wire.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 4 Helpful 12
Question
How do you test earthing with a multimeter?
Ricardo Mitchell
Electrician & Construction Professional, CN Coterie
Ricardo Mitchell is the CEO of CN Coterie, a fully licensed and insured Lead EPA (Environmental Protection Agency) Certified construction company located in Manhattan, New York. CN Coterie specializes in full home renovation, electrical, plumbing, carpentry, cabinetry, furniture restoration, OATH/ECB (Office of Administrative Trials and Hearings/Environmental Control Board) violations removal, and DOB (Department of Buildings) violations removal. Ricardo has over 10 years of electrical and construction experience and his partners have over 30 years of relevant experience.
Ricardo Mitchell
Electrician & Construction Professional, CN Coterie
Expert Answer
A multimeter has three prongs on it, and you can just plug it into the outlet. It should read whether the outlet is grounded or not.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 17 Helpful 2

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Outlets that only have 2 ports on them are not earthed.
Thanks
Helpful1 Not Helpful1

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Call a trained electrician if you don’t feel comfortable testing your home for earthing on your own.
Thanks
Helpful5 Not Helpful1
Never use an uninsulated wire or multimeter since you could get seriously shocked or electrocuted.
Thanks
Helpful3 Not Helpful1