How to Put a Nail in a Concrete Wall

Download Article

Two easy ways to hammer nails into concrete by hand

Download Article

Anchor Nails

|

Masonry Nails

|

Expert Q&A

|

Warnings

|

Things You'll Need

The toughness and durability of concrete makes it a popular building material for walls. Concrete walls can also add a modern, industrial aesthetic to a room. However, their strength and durability can make it difficult to drive nails into them. Fortunately, there are specialized tools and materials you can use to make the job easier. To minimize the risk of cracking the concrete, you’ll want to use a hammer-set anchor nail. You could also drive masonry nails into the wall for an easy and convenient option.

Things You Should Know

Using a hammer drill, drill a hole and insert a hammer-set anchor nail into that hole; tap the nail into place with a standard hammer.
Nail a sturdy masonry nail into concrete by repeatedly hitting it with a mash hammer—strike carefully and directly to avoid bending the nail.
For safety, wear a face mask and safety glasses and gently fasten masonry nails into the wall before you begin hammering with full force.

Method 1

Method 1 of 2:

Anchor Nails

Download Article

1
Choose hammer-set anchor nails for concrete walls. Hammer-set anchor nails are what’s known as mechanical drive anchors. They consist of a wider section at the bottom that’s designed to expand and a thinner top section that looks like a standard nail. They’re tough enough to be hammered into concrete, but you first need to drill a guide hole into the wall. Look for hammer-set anchor nails at your local hardware or home improvement store.^{[1]XResearch source}
- You can also order hammer-set anchor nails online.
2
Put on a pair of safety glasses and a face mask. Drilling into concrete creates dust that can irritate your eyes if it gets into them and your sinuses if you breathe it in. Before you begin working, put on a pair of well-fitting safety glasses and cover you nose and mouth with a facemask.^{[2]XResearch source}
- You could also tie a scarf or bandana around your mouth and nose to avoid breathing in the concrete dust.
- You can find safety glasses and face masks at hardware stores, department stores, and by ordering them online.
Advertisement
3
Fit a carbide-tipped masonry bit into a hammer drill. A hammer drill, also known as a percussion or impact drill, is a specialized power tool that’s used to drill into hard surfaces, such as concrete. Insert a carbide-tipped masonry bit into the end of your drill and tighten it so it’s held securely in the jaws.^{[3]XResearch source}
- Look for hammer drills and carbide-tipped masonry bits at your local home improvement or hardware store. You can also order them online.
- Carbide-tipped masonry bits are strong enough to drill into concrete without cracking.
Tip: If you don’t have a hammer drill, you can use a standard power drill, but you must use a carbide-tipped masonry bit and it will take much longer to drill into the concrete wall.
Take a wide stance and plant your feet firmly on the ground so you’re strong and stable. Press the drill bit against the wall where you want to put your nail, hold the drill with both hands, and apply pressure using your body weight so the drill won’t slip or move out of place when you use it.^{[4]XResearch source}
5
Drill a hole into the wall deep enough to fit your hammer-set anchor. With your drill pressed against the wall, start drilling slowly and bring it up to full speed to create a pilot hole in the wall. Make the hole as deep as the wider bottom section of your hammer-set anchor.^{[5]XResearch source}
- If concrete dust builds up in the hole as you’re drilling, remove the drill and blow out the dust before you continue.
Hold the wider bottom section of the hammer-set anchor nail against the hole you drilled and start tapping it into place with a standard hammer. As you drive the anchor into the concrete, the bottom section will expand and hold the nail in place. Continue hammering until the wide section is completely in the wall.^{[6]XResearch source}
Scot Simpson, Construction Expert
If you're attaching stuff to concrete, having the right tools and supplies is key. For nailing, go with a hardened steel nail made specifically for concrete — that way, it can get through the hard surface without bending. You can also pre-drill holes with a hammer drill for the nails, then drive them in with a heavy hammer. Be sure to wear safety goggles to keep debris from flying into your eyes.

Method 2

Method 2 of 2:

Masonry Nails

Download Article

Pinpoint the exact spot where you want to put your nail by using a pencil or marker to make a small point on the wall. If you plan to install multiple nails into your wall to hang or install something, check to make sure they’re measured evenly with a ruler or tape measure.^{[7]XResearch source}
2
Hold a masonry nail against the concrete wall with your fingers. A masonry nail, also known as a concrete nail, is made of tough steel and designed with fluted shafts that help them drive into concrete without breaking. Place the tip of the masonry nail against the marking you made and hold it steady with your fingers.^{[8]XResearch source}
- Look for masonry nails at hardware stores, home improvement stores, department stores, or by ordering them online.
3
Tap the nail with a 2 lb (0.91 kg) mash hammer to hold it in place. A mash hammer, also known as a masonry hammer, as a double-sided hammer that’s much heavier than standard hammers, making it the best choice to drive nails into concrete. With your nail held in place against the wall, tap the end of it with your hammer to drive the nail just enough so it’s held in place in the wall and you don’t need to hold it with your fingers.^{[9]XResearch source}
- A standard hammer won’t be heavy or solid enough to drive the nail into the concrete wall.
- Look for mash hammers at hardware stores and home improvement stores, or by ordering one online.
4
Drive the masonry nail into the concrete wall with the hammer. Use carefully aimed hammer strikes to drive the nail into the concrete wall so you don’t miss and bend the nail or strike the wall and damage it. Continue striking the hammer until the nail is driven in to where you want it.^{[10]XResearch source}
- If you’re fastening something to the concrete wall, drive the nail all the way in.
Tip: Leave about ¹⁄₂ inch (1.3 cm) of the nail sticking out if you plan to hang something from it.

Expert Q&A

Search

Add New Question

Question
How does a Hilti nail gun work?
James Mansfield
Construction & Design Specialist
James Mansfield is a Construction and Design Specialist and the CEO of WestVillage General Contracting, a high-end and luxury design/build firm in New York City. James specializes in apartment, bathroom, and kitchen remodeling as well as fine cabinetry, lighting, paint, and wallpaper. James has developed a proprietary system of construction called the Luxury Build Method that hinges on a skilled team, respected partnerships, and clear, transparent communication. WestVillage GC has completed more than 500 commercial and residential projects in New York with designers such as David Scott Interiors and Fox Nahem, Kelly Behun. WestVillage GC is also a preferred contractor for Related buildings including Hudson Yards.
James Mansfield
Construction & Design Specialist
Expert Answer
A Hilti gun comes with 22-caliber charges that look like two bullets—they're color-coded based on their power. You can then shoot those charges straight into the concrete.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 3