Nintendo Switch Battery Replacement Guide

Download Article
Easy steps to take apart, open, and remove your Switch’s battery
Download Article

Is the battery on your Nintendo Switch barely holding a charge or not charging at all? This How.com.vn article teaches you how to replace the battery in a Nintendo Switch and how to figure out what generation Switch you have. Note that this process isn't recommended by Nintendo, and it may damage your console.[1]

Things You Should Know

  • You can replace your own Nintendo Switch battery if you have a screwdriver, K-9 thermal paste, a new battery, and confidence in taking tech apart.
  • Nintendo advises against replacing your own Switch battery, and the process will void your warranty.
  • To get the correct replacement battery, you'll need to find your Switch's generation, which you can do by deciphering the model number on the back.
Section 1 of 2:

Replacing the Battery

Download Article
  1. How.com.vn English: Step 1 Make sure the battery is below 25%.
    This will reduce the fire risk if your battery is damaged during this process. If the battery is swollen, there's a greater chance that it will explode or catch fire. In that case, take the Switch to a professional, and don't attempt to replace the swollen battery yourself.
    • If your battery smells bad or feels hot, don't attempt to remove the battery. Never breathe in fumes from a smoking battery, and take immediate action to reduce the fire hazards in the area.
    • If the battery should catch fire, smother it with sand, use foam or CO2 fire extinguishers, pour cold water over it, cover it with a fireproof container, and stand clear.[2]
  2. How.com.vn English: Step 2 Remove the Joy-Con controllers.
    With your device off and below 25% battery life, press the locking mechanisms on either side of the Switch to take off the Joy-Con controllers.
    Advertisement
  3. How.com.vn English: Step 3 Remove the screws on the back.
    Turn your Switch over and unscrew the four screws holding the backplate on your console.
    • Keep your screws organized since they can be different screws or vary sizes!
  4. How.com.vn English: Step 4 Remove the top and bottom screws.
    There are two screws that you need to unscrew: one at the top of your console and the other that's along the bottom edge.
  5. How.com.vn English: Step 5 Remove two screws around the edges.
    Centered on either side of your Switch are two more screws that you need to remove. They are slightly longer than the other screws.
  6. How.com.vn English: Step 6 Flip up the kickstand and remove your microSD.
    If you don't have a microSD inserted in your Switch, don't worry about that part. You need to flip the kickstand up, however, to continue.
  7. How.com.vn English: Step 7 Remove the screw in the kickstand well.
    Unscrew this screw (it's smaller than the others) under the kickstand and close it.
  8. How.com.vn English: Step 8 Pull off the back panel.
    This is the game cartridge flap. You should be able to pull it up to remove it.
  9. How.com.vn English: Step 9 Remove the screw in the microSD card reader and pull out the driver.
    Once you've unscrewed the small screw inside the microSD card reader, you can pull the entire thing out.
    • If you cannot remove the card reader with your fingers, use a small tool like a pair of tweezers to lift it.
  10. How.com.vn English: Step 10 Unscrew 6 screws around the shield plate and take it off.
    You can pull off the shield plate after you've removed the 6 screws holding it into place.
    • If you have a newer model, you most likely have a foam piece to remove. Use your fingers or tweezers to remove it. Don't yank it if it doesn't come off easily since it can tear. Instead, pull at different spots to remove it.
    • If the shield plate is tough to remove, insert a plastic chip or spudger under it. You'll see thermal paste lining the other side of the shield plate. This paste prevents your Switch from overheating.
    • You can reuse the thermal paste from the shield plate if it isn't dirty. If the paste doesn't look good, use K-9 thermal paste instead.
  11. How.com.vn English: Step 11 Disconnect the battery.
    Use a small and pointed tool like the pointy end of the spudger to pry off the battery connector. Pry it straight out of its socket so you don't bend anything.
    • Don't pull the socket out of the motherboard. Use your tools to hold the socket down while you remove the connectors.
  12. How.com.vn English: Step 12 Remove the battery.
    Apply a few drops of adhesive remover or isopropyl alcohol (90% or higher) inside the battery well. Allow either liquid ample time to dissolve or loosen the adhesive, which may take 2-20 minutes.
    • Since the battery can be challenging to remove, you might want to lift a corner using the spudger or plastic putty knife, then use floss to peel the battery away from the adhesive.
    • Be very careful if you use heat to loosen the adhesive! Heating your battery incorrectly can cause it to explode or catch fire.
    • Avoid bending the battery as you remove it.
  13. How.com.vn English: Step 13 Clean the battery well of the remaining adhesive.
    Once the battery has been removed, you can clean the area so there's no more adhesive or liquid.
  14. How.com.vn English: Step 14 Insert your new battery and reassemble your Switch.
    You can follow this tutorial in reverse order to put your Switch back together. You'll need to reconnect the battery, replace the shield plate, put the microSD card reader back, screw in screws, put the cartridge flap back, screw in a screw in the kickstand well, and replace more screws.
  15. Advertisement
Section 2 of 2:

Find Your Switch's Generation

Download Article
  1. How.com.vn English: To get a replacement battery, you'll need to know which generation Switch you have.
    Just turn your Switch over so the front faces down and the back is visible. Look for "Mod" to find the model number.
    • HAC-001: Original Nintendo Switch
    • HAC-001(--01): New Nintendo Switch
    • HDH-001: Nintendo Switch Lite
    • HEG-001: Nintendo Switch OLED

Expert Q&A

Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
Submit
      Advertisement

      Video

      Tips

      Submit a Tip
      All tip submissions are carefully reviewed before being published
      Thanks for submitting a tip for review!

      Things You'll Need

      • K5‑PRO Viscous Thermal Paste
      • Isopropyl Alcohol
      • Microfiber Cleaning Cloths
      • Spudger (or small, thin tools like plastic chips and tweezers)
      • Small screwdrivers, like Y00 or Y0.
      • Replacement battery

      About This Article

      How.com.vn English: Darlene Antonelli, MA
      Written by:
      How.com.vn Technology Writer
      This article was co-authored by How.com.vn staff writer, Darlene Antonelli, MA. Darlene Antonelli is a Technology Writer and Editor for How.com.vn. Darlene has experience teaching college courses, writing technology-related articles, and working hands-on in the technology field. She earned an MA in Writing from Rowan University in 2012 and wrote her thesis on online communities and the personalities curated in such communities. This article has been viewed 1,292 times.
      How helpful is this?
      Co-authors: 3
      Updated: April 15, 2024
      Views: 1,292
      Thanks to all authors for creating a page that has been read 1,292 times.

      Is this article up to date?

      ⚠️ Disclaimer:

      Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
      Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.

      Notices:
      • - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
      • - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
      • - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
      • - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.

      Advertisement