How to Make an Adjustable Rope Halter

A rope halter is good to have around for cattle, sheep and goats, and it's an absolute necessity around the farm and ranch. It's much cheaper to make an adjustable halter than to go and buy a horse halter from a feed store and find out it's not the right size for the animals you're needing to use it on.

Homemade halters are great to use to teach livestock, like cattle, sheep, and goats, to lead, to do routine handling in day-to-day activities, and to restrain them when necessary.^{[1]XTrustworthy SourceScience DirectOnline archive of peer-reviewed research on scientific, technical and medical topicsGo to source} A halter's low cost allows the producer to make extras to place around the farmstead where and when needed.

Things You Should Know

Use a 12 to 15 ft (3.7 to 4.6 m) piece of 3-stranded cotton or nylon rope.
Whip both ends of the rope to prevent fraying and unraveling.
Separate the strands and use a series of knots and loops to make the halter.

Steps

Download Article

Any type of rope, from cotton to nylon will work. However your choice depends on the strength needed, durability required, and the cost. Smaller rope that is 1/4" to 3/8" (6.35mm to 9.52mm) diameter is suitable for sheep and goats.^{[2]XResearch source}
2
Finish one end of the rope by whipping it, clamping it with a ferrule, dipping, or heat-treating it.^{[3]XResearch source} Note that the method you select depends on your wishes and the type of rope being used. Failure to finish the rope ends will result in fraying and un-laying.
- Temporarily finish the other end of the rope with tape or string.
- You will need to form a crown knot into this end after the halter is completed.
Advertisement
Refer to this length as the short end of the rope. The remaining length is the long end.
4
Place the short end on your right and the long end on your left. Grasp the rope at the 12" to 15" (30.5cm x 38cm) mark between your thumb and first two fingers (fore and middle) of both hands.^{[4]XResearch source}
- Separate your right and left hands by around 2" (5cm) apart.
- Rotate the rope clockwise with your right hand and counterclockwise with your left. This will open the strands of the rope between your hands.
Use your right hand to insert the whipped end of the short end of the rope under the strand opening until the loop formed has an eye opening of around double the diameter of the rope.
6
Position the rope so that the eye loop is on your left hand with the short end pointing towards 3 o'clock and the long end pointing towards 6 o'clock. Grasp the eye loop and the single strand running across the short end of the rope between your left thumb and forefinger.^{[5]XResearch source}
- With your right thumb and forefinger, grasp the short end of the rope at a point near the eye loop.
- Twist the eye-loop and short end of the rope with your hands until you have isolated two strands between your right thumb and forefinger.
7
Use your left hand to insert the long end of the rope from the bottom up under and through these two strands.
- Pull it completely through until there's no slack. If you have done it properly up to now, one side of the loop will show three strands lying smoothly side-by-side. This is important because they will be positioned against the animal's face.
8
With the eye loop in your right, grasp the short end of the rope between your left thumb and forefinger about 2 inches (5cm) from the whipped end. Two inches farther from the whipped end, grasp it in the same manner in your right hand (your hands should be 2 inches apart, the left closest to the short end than the right).
- Open the strands by twisting clockwise with your right hand and counterclockwise with your left.
- When the strands are opened wide, push your hands together. This will cause the strands to buckle and fold over, forming three loops.
Use your right hand to feed the long end of the rope into the loops, starting at the one closest to the eye loop. Remove the stick from one loop at a time as you run the long end of the rope through them.
This completes the halter!
11
Permanently finish the long end of the rope halter in the manner you choose. Consider making a crown knot at the end because a crown knot and back splice creates a convenient handle.
- Do not use a hog ring to finish the end since it could catch and tear the skin of your hand.

Community Q&A

Search

Add New Question

Question
How can you find that long a piece of rope?
Community Answer
Go to your local farm and ranch supply store; most of them sell rolls of rope of various sizes, types and colours you can choose from to make a rope halter. Select the length you need and you use that to make your rope halter. Remember to burn the ends first before you begin so that the rope doesn't unravel on you.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 7 Helpful 12
Question
I have a head harness for my pup I've been using for training. When she pulls it tightens around her muzzle so she will let it go slack. Will this harness do the same?
Karin
Top Answerer
This is a halter, which is different from a harness. Halters are intended for controlling the head of large animals, not as a training device for a dog to stop pulling on the lead, and it also fits differently on a bovine versus a dog. The head strap is designed to go behind the ears, under the chin and over the muzzle, not at the throat like with a head harness built for dogs.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 8 Helpful 8
Question
How do you put it on?
Karin
Top Answerer
Usually it's nose-first, then over the ears, although you can go vice versa as well if the animal is a little uncooperative. The beauty of this halter is that it adjusts so to slip easily over the ears and the nose, then tightens as you pull on the lead shank.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 5 Helpful 7