How to Install a New Handlebar Grip

New grips can make a bike feel like brand new. While an admittedly small part of the bike, handlebar grips and tape are a key factor in how comfortable you are on the bike. The good news is that you don't need a bike shop to get install your own handlebar grips

Installing Bicycle Grips

Pry off the grip with a screwdriver and WD-40. Clean the bar with soap and water.
Spray hairspray or hand sanitizer inside the new grip. Or, place plastic ties inside.
Push the grip onto the bar, twisting and turning it as you push.

Method 1

Method 1 of 2:

Replacing Rubber Grips

Download Article

1
Carefully slide or cut off the old grip. Sometimes, careful cutting with a razor blade is necessary; try not to scratch your chrome. If you want to save the grips without cutting, spray WD-40 between grip and handlebar, giving it 5-10 minutes to work its way into the grip. Twist to spread the WD-40 inside the grip and pull it off easily.
- Stick a screwdriver between the bar and the grip if you cannot get under the grip well, using it to prop the grip up while you spray it down.
- If stuck, you can use compressed air from a compressor or can to remove a grip.^{[1]XResearch source}
2
Clean bar with soap/water to remove WD-40, dust, and gunk. Give the bars a good clean scrub, using an old rag or sponge to get them as clean as possible. This will make it much easier to get the new grip on and keep it there. When done, dry the whole thing off.
- If they are open on the ends, make sure you dry off the inside of the handlebar as well. Water left in there after putting the new grip on can lead to rusting.
Advertisement
3
Use 3-4 long, plastic ties as "runners" to slide your grip on. Place the plastic ties in the grip on different sides, then use these smooth, low-friction areas to slide the grip onto the bike. Then simply pull the ties back out to finish installing.
- Note that lock-on grips are gaining popularity -- they require a hex wrench (Allen key), but you can easily loosen the bolt, slide the grip on, then tighten it in place.^{[2]XResearch source}
If you don't have plastic ties, a little bit of an alcohol-based product, such as hairspray or sanitizer, may help you slide the grip easily. As a bonus, the grip will definitely stay on once you've got it in place. While not strictly necessary, this step can prevent the grip from immediately slipping off the bar if you have issues.^{[3]XResearch source}
^{[4]XResearch source} It can help to twist as you push, working it onto the handlebar bit by bit. While the snug fit may make it hard to get the grip on, you'll be thankful later when it doesn't come off mid-ride.^{[5]XResearch source}

Method 2

Method 2 of 2:

Applying Taped Handlebar Grips

Download Article

1
Cut or unwind the old handlebar tape. You will rarely have to cut the tape off, and you should be careful not to nick the actual handlebar if you do. More often than not, you can simply unwind the old tape off the bike. Remove the cap at the end of the handlebars, using a flat-head screwdriver if needed.^{[6]XResearch source}
- Before removing, note how far up the bars the old tape went. This is a good guide for when to end your own tape-up.
Use a gentle degreaser, or some simply warm water and dish soap, to lightly remove the rest of the adhesive.^{[7]XResearch source}
3
Set up your workstation and prepare the bars for taping. Take some electrical tape and wrap any cables lightly to the bars, if they are not already pre-attached. Note where you want the tape to end, and get your knife or scissors ready to cut the excess tape when you're finished.^{[8]XResearch source}
- Feeling extra pro -- wrap some double-sided tape around the bottom 2-3 inches of the bar to help keep your tape in place.^{[9]XResearch source}
4
Start each handlebar from the bottom, wrapping clockwise on the right and counter-clockwise on the left. Handlebars need to be wrapped in a way that prevents unwinding while you ride. Starting from the bottom prevents the wrap from sliding down under your hands. Furthermore, wrapping in the right direction for each hand prevents you from unwrapping as you ride (many people, when tired, clench their hands and twist them outwards).
- Pull the tape tight -- you want a lot of tension for a tight, waterproof grip.^{[10]XResearch source}
Move up the bar, overlapping slightly for 3-4 wraps. Then push the cap into the exposed wrap, sucking it into the inside of the handlebar so that the cap holds the bottom of the tape in place. Repeat on both sides.^{[11]XResearch source}
6
Work slowly, overlapping about a quarter of the tape with every turn, as you move up the bar. If there is adhesive in tape, it is often covered. Pull off the covering now and slowly, tightly wrap the tape up and around the bar. You may have to pull and work the tape multiple times, making sure there are no gaps.
- It is often best to test the tension of the tape before starting. Give a good tug to feel how tightly you can pull on the tape without ripping it.
- To avoid gaps where the bar bends, you may have to overlap a bit more.
The top of the handlebars, the flat part, need to be wrapped in reverse. As you finish the bottom of the bars, get as close to the levers as you can. Then skip over a small area where the bars bend and just start wrapping the top of the bars.
8
Reverse your wrapping direction for the top of the bars. This will be easy if you skip past the lever covering, as outlined above. Most riders will rotate their wrists back on the top bar, potentially unraveling the tape. This is why you change directions when getting to the top bar:^{[12]XResearch source}
- The right side should be wrapped counter-clockwise.
- The left side should be wrapped clockwise.^{[13]XResearch source}
You can "overwrap" it, then use a pen to mark the points you want to cut it. Then simply follow this line with scissors for a clean, professional tape-up.
10
Add some 2-3 wraps of electrical tape to hold the wrap in place. At the very end of the tape, use some "finishing tape," to secure the wrap in place. Add enough that it cannot be easily unwound, usually using 1-2" on the tape and 1-2" on the bike frame.
- For a better hold, use a lit match to melt the tapes together in a few places, "welding" your handlebar tape on.^{[14]XResearch source}

Community Q&A

Search

Add New Question

Question
Can I use hair gel instead of hairspray?
Community Answer
No, that won't work. Hairspray works because it eventually evaporates. Gel will just stay there and make your grip slip away from your handlebar.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 11
Question
Now that I know how to put them on - where can I buy replacement grips for a 16 inch bicycle?
Alonzo V
Community Answer
Every Walmart superstore sells them with many different options. Or find your nearest bicycle store.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 2
Question
Does antiseptic solution work?
LibArtsPremed18
Top Answerer
Alcohol can help with installing new grips, as it decreases friction and dries quickly. However, I would only recommend pure rubbing alcohol, not a substance containing it, as the chemicals may damage the grips or bars.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 1

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Ordinary spit will also work if you don't have hairspray or sanitizer.
Thanks
Helpful3 Not Helpful1
Using oil or soapy water or anything like that (to apply grips) will simply make your grip slide around on the bar for the rest of the time you own the bike.
Thanks
Helpful3 Not Helpful1

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Be very careful with blades around your bike frame, especially if the frame is carbon fiber. Small nicks and cuts can compromise the frame's stability in the case of a crash.
Thanks
Helpful1 Not Helpful3