How to Install Metal Studs

Steel framing is used in most office and commercial construction, and it has several advantages over wood. Steel studs are perfectly straight, and they don’t shrink, split, rot, or mold. They are also easy to store. Read on to find out how to build with steel studs.

Part 1

Part 1 of 2:

Measuring and Hanging the Track

Download Article

1
Rent or purchase the right tools. Working with steel studs requires a few special tools. You can typically get the best equipment for this at local construction rental stores. You will need:
- Metal cut-off saw
- Fasteners
- A hammer drill
- Screw gun
- Chalk box
- Level
- Laser level or plumb bob^{[1]XResearch source}
- Clamps
You should typically allow for 1 stud per every 12 inches (300 mm) of linear wall space. Purchase steel plates — also called tracks — for the bottom and top of the wall by measuring the linear feet of the wall and doubling it. Add an additional stud for each side of a window or door.
Advertisement
Snap a chalk line across the perimeter of the floor to outline where your track will need to go.
4
Screw the lower lengths of track to the floor. Use the chalk line to position your lower track and screw the track in by first drilling a hole into the track and stud, and then fastening with a screw. If you're drilling through concrete, try using the power nailer or hammer drill for an easier time.^{[2]XResearch source}
- Negotiate corners and long straight lines when laying track. Overlap track corners by flattening the first track’s side flange so the overlapping track can slide right into place. On longer, straight runs, overlap the adjoining tracks at least 6 inches and secure the overlap to the floor with a concrete screw.^{[3]XResearch source}
5
Plumb the top track. To make sure that the upper and lower track are plumb, you can use either a laser level, a plumb bob, or two water levels:
- To use a laser level, simply place it in the bottom middle of the track and turn it on to shine a vertical laser up to your wall. This point will be your plumb point on the upper wall. Most contractors recommend using a laser level for efficiency and ease of access.
- Using a plumb bob is similar to using a laser level. Attach the string to the top of the wall and let the bob come to a rest at the plumb line on the bottom of the floor.
- If you have neither a laser level nor a plumb bob, you can try using two water levels pressed together. Keeping both levels together, extend one to the ceiling and other to the floor, making sure that both levels are plumb. Mark off your plump line on the floor or ceiling.
6
Once plumb is established, attach the track to the upper ceiling. Use a drill and screw gun to the attach the track, pretty much just as you attached the ground track.
- If your track runs perpendicular to the ceiling joists, fasten the track to the joists with self-tapping drywall screws.
- If your track runs parallel to the ceiling joists, fasten the track to the joists with drywall anchors or secure it with grabber screws and glue.^{[4]XResearch source}

Part 2

Part 2 of 2:

Fastening the Metal Studs and Finishing Up

Download Article

1
To trim to correct length, cut both side flanges of a steel stud. Use straight-cut aviation snips for this. Bend one flange up, clear of the snips’ jaws, and cut across the stud’s web.
- For easier electrical and plumbing installations later on, keep all the keyhole knockouts aligned by cutting all studs to length from the same end. Protect your hands with heavy-duty gloves.
- To cut multiple pieces at once, use a miter saw with a metal cutting blade.
- Make cutting the studs with aviation snips easier by first scoring the studs with a utility knife on both sides and then bending the stud back and forth until it breaks apart.
2
Join studs to tracks by clamping the two members tightly with C-clamp locking pliers. Drive a 1/2 inch (1.2 cm) No. 8 pan-head screw in the middle where they meet. This should be done at medium speed.^{[5]XResearch source}
- Choose a clutch setting strong enough to drive the screw home, but not so strong that it strips the screw hole and weakens the joint.
Cut each flange of the track (on both ends) 1 inch (2.5 cm) lengthwise. Bend the web down 90 degrees using sheet metal locking pliers.^{[6]XResearch source}
Pop a plastic bushing into each knockout in order to keep the cable from rubbing against the sharp edges.
If your steel stud wall seems flimsy, keep in mind that it gains full rigidity once drywall or sheathing is applied.
6
Hang drywall or sheathing using 1-1/4 inch (3.1 cm), self-tapping drywall screws. They should be spaced every 8 inches (20.3 cm) along edges (where two sheets meet on a stud) and 12 inches (30.5 cm) on centers located elsewhere.
- Use screws with a fine thread instead of a coarse one.
- Check your local codes. They may require screws placed closer together, and you're better off having too many than having to add more after the inspector comes.
Your new metal studs won't rot, sag, or be susceptible to fire. Learn how to hang drywall and finish the process.

Expert Q&A

Search

Add New Question

Question
When should gypsum go to deck?
Mark Spelman
Construction Professional
Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
Mark Spelman
Construction Professional
Expert Answer
Fire-rated walls will need drywall to deck.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 8
Question
Can I use metal studs with Oriented Strand Board?
Mark Spelman
Construction Professional
Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
Mark Spelman
Construction Professional
Expert Answer
Yes, you can definitely install metal studs on a Oriented Strand type Board.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 5
Question
I find that the pan-head framing screws prevent drywall from laying flat on the studs and even causes cracking at corners. Am I doing something wrong?
Mark Spelman
Construction Professional
Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
Mark Spelman
Construction Professional
Expert Answer
To prevent cracking, I recommend using fine threaded drywall screws.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 16 Helpful 5

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Install door jacks.
Thanks
Helpful42 Not Helpful20
Steel studs are sold in a variety of widths that are comparable to dimensional lumber sizes.
Thanks
Helpful29 Not Helpful15
With lengths and gauges, the lower the gauge number, the thicker the steel.
Thanks
Helpful24 Not Helpful12

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Make sure that your architect or designer's plans aren't drawn for wood dimensions.
Thanks
Helpful9 Not Helpful5
Don’t try nailing trim into steel studs, unless it is a light gauge stud. It will not hold. Instead, use specially designed trim screws for the job.
Thanks
Helpful2 Not Helpful0
For heavy cabinets such as overhead kitchen cabinets, keep in mind that steel studs may not be strong enough to support their weight, even with drywall on them. Install solid wood blocking to these areas to help hold up the cabinets.
Thanks
Helpful3 Not Helpful1
Doing any type of work using power tools while tired or in a rush may lead to injury.
Thanks
Helpful8 Not Helpful10
Cut steel is sharp, so make sure to wear gloves.^{[7]XResearch source}
Thanks
Helpful0 Not Helpful0
Wear eye protection when cutting steel and driving screws. It's not unheard of for a screw to jump off the power screwdriver and shoot out at you.^{[8]XResearch source}
Thanks
Helpful0 Not Helpful0