How to Install Ceiling Drywall

Installing ceiling drywall (or sheetrock) is a very simple process, and with the right info, you'll be able to manage it in a snap. If you make the right preparations and install your drywall in the correct procedure, you should have no problem installing drywall on your ceiling. Let's get started!

Part 1

Part 1 of 2:

Preparing the Ceiling and Drywall

Download Article

1
Inspect the ceiling for obstructions or problems that need to be fixed. Before you install the drywall, check to make sure electrical wires, ductwork, protruding pipes, and other obstructions won’t be in your way. As well, take this opportunity to make sure there aren’t any obvious issues, such as faulty plumbing, that would be easier to address without drywall in the way.^{[1]XResearch source}
- Install furring strips to the framing in order to create a flat, even surface for drywall installation around these obstacles as necessary.
2
Find the ceiling joists and mark their location on the wall. You’ll need to know where the ceiling joists are located at all times during this process. If you can’t see the joists, tap on the ceiling with a hammer and listen for a solid sound indicating wood framing.
- You can just use a pencil to mark the locations on the wall.
Advertisement
3
Mark the placement of light fixtures and vents on the drywall. Note where the different light fixtures, vents, and electrical boxes are located on the wall and mark their locations on the drywall you plan to place on top of them. You’ll need to wait until after the drywall is attached to the ceiling before cutting holes in it for these fixtures.^{[2]XResearch source}
- You might also precisely mark these locations on a plan of the ceiling, noting their exact distance from the walls.
Smoothing the rough edges on the cut edges of your drywall pieces will ensure tight joints between the drywall. Use a surform tool to sand down the edges of the drywall until they’re smooth.^{[3]XResearch source}
5
Build a T-brace if you’ll be working alone or without a lift. A T-brace will provide the leverage and support needed to raise the drywall panels to the ceiling when you're working alone. Use a 2 feet (61 cm) piece of 1x4 and nail it to a 2x4 that is long enough to be 1 foot (30 cm) higher than the length from the floor to the ceiling.^{[4]XResearch source}
- A T-brace isn’t necessary if you’re using a drywall lift, which is a machine that smoothly lifts drywall to the ceiling so you don’t have to lift it. Drywall lifts can be cheaply rented from department stores and most stores that sell construction equipment.

Part 2

Part 2 of 2:

Attaching the Drywall to the Ceiling

Download Article

1
Apply adhesive to the joists where the first sheet of drywall will go. Start in the corning and raise the first sheet of drywall to the ceiling so you can get an idea of the placement across the joists. Wait until you know where you're placing the sheet before you apply any adhesive to the joists.^{[5]XResearch source}
- Drywall adhesive dries within 15 minutes, so make sure you’re ready to begin placing the drywall as soon as you apply the adhesive.
2
Raise the first piece of drywall to the ceiling. Using your T-brace, or a friend to assist you, raise the first sheet of drywall to the ceiling and slide it snugly into the corner. Make sure that the tapered edges of the sheet are facing the floor.^{[6]XResearch source}
- If you’re using a drywall lift, move the lift underneath the ceiling and place the drywall sheet on the lift so that it is directly under the corner of the ceiling. Lift it slowly, making sure the sheet doesn’t jostle or move out of position.
3
Repeat this process along the first wall. Attach the next piece of drywall using this same process and continue along the wall, always ensuring that the tapered edges abut one another and are facing down.
- The tapered edges are designed to make the process of taping and mudding easier, so it’s important that they remain facing down.
4
Affix the drywall sheets permanently to the ceiling joists. Use either nails or screws to attach the drywall to the joists. Drive the fasteners in .375 inches (0.95 cm) away from the edges of each sheet and space them 7 inches (18 cm) apart along the perimeter. Along the interior joist, install the fasteners at about 12 inches (30 cm) increments.
- The heads of the fasteners you choose should come in contact with the paper facing, sinking in slightly without breaking through the paper.
5
Start the second row with a half sheet of drywall to stagger the seams. When you finish the first row of drywall and move on to the second, make sure the seams don’t line up between the two rows. Having staggered seams will enforce the stability of the drywall.
- Measure and mark the cut line at the vertical midpoint of the drywall sheet and use a utility knife to cut through the drywall. Tip the panel off of the floor or table at a slight angle, then push it down to break it in half.
- Use the same procedure to attach this half-piece of drywall as you used on the first row of drywall.
Continue to place drywall in rows along the ceiling, affixing them in place with nails or screws. As you move from one row to the next, make sure to stagger the seams to ensure the drywall’s stability.
Now that the drywall is set, go back and cut holes in the places you marked for vents, lights, and electrical boxes. Use a spiral cutout saw to make the cutting process quick and easy.^{[7]XResearch source}

Expert Q&A

Search

Add New Question

Question
Can I sheetrock a ceiling myself?
Agustin Renoj
Home Improvement Specialist
Agustin Renoj is a Home Improvement Specialist with Renoj Handyman based in the San Francisco Bay Area. With over 18 years of construction experience, Agustin specializes in carpentry, painting, and exterior, interior, kitchen, and bathroom renovations. Renoj Handyman is a family-owned business that consists of craftsmen trained in all areas of construction.
Agustin Renoj
Home Improvement Specialist
Expert Answer
The best thing to do is to hire someone who does that for a living—it will get finished much faster and will usually look much nicer. If you do decide to do it yourself, you're going to need at least two people to help you, because sheetrock is very heavy and you can easily get hurt.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 40 Helpful 9
Question
How do I repair a ceiling where a portion is falling in and needs to be replaced?
Community Answer
Mark off a squared or rectangular-shaped line around the damaged area. Determine the orientation and location of the ceiling joists. Extend your squared off markings so that two opposite sides of the outline fall on center, directly over the ceiling joists. Cut out the box shape, and install new drywall into the area. Fasten along the edges falling over the joists. Also, make sure all of the damaged drywall is removed and that the problem that caused it is also repaired. Finally, finish as you would a regular drywall installation.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 6 Helpful 14
Question
How do I drywall a ceiling that needs insulation?
Community Answer
Install friction fit batts, sized to meet the code requirements in your area; cover the area completely with 6 mil poly, taping all joints; then fasten up the drywall.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 11 Helpful 26

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Keep the drywall sheets laid out flat on the floor until you're ready to use them. This will prevent them from bending.
Thanks
Helpful58 Not Helpful26
Professionals rarely use glue on ceiling joists, partly because of the greater likelihood of ceiling boards needing to be taken down and trimmed. Instead of gluing, we generally use three coarse thread drywall screws(or three sets of two nails) in the "field" in addition to the screw on each edge of the board.
Thanks
Helpful18 Not Helpful19
The joists should be marked on the top "plate," the plate is typically made of two 2x4s on top of the studs.
Thanks
Helpful2 Not Helpful2