How to Hang Lights from a Ceiling

Hanging a swag light or light fixture from your ceiling may seem like a daunting task, but it’s actually rather simple. You only need a few basic tools and a little bit of time to tackle this project. If you own the property, you can install a light fixture directly into the ceiling. If you rent, or just want a more temporary solution, you can hang a swag light from a hook or anchor and plug it into an outlet.

Method 1

Method 1 of 2:

Installing a Light Fixture in the Ceiling

Download Article

Before you do anything else, you need to turn off the circuit breaker. If you aren’t sure which breaker turns off the light, turn off the main breaker and use natural light or a headlamp to complete this project.^{[1]XResearch source}
Use a screwdriver to remove the screws, or an impact driver with a hex-shaft to remove the nuts, that secure the canopy (the dome-shaped cover) to the ceiling. Then, use a screwdriver to remove the screws that secure the crossbar to the electrical box. Disconnect the wires on the fixture from the wires in the ceiling by removing the wire connectors and untwisting the wires. Carefully lower the old fixture to the floor.^{[2]XResearch source}
EXPERT TIP
Jeff Huynh
Professional Handyman
Jeff Huynh is the owner of Moseybolt, a full service solution in home services, renovations, and repair in the Greater Seattle area. He has over five years of handyman experience. He has a BS in Business Administration from the San Francisco State University and his Certificate in Industrial Electronics Technology from North Seattle College.
Jeff Huynh
Professional Handyman
Make sure your light will be secure. According to Jeff Huynh, the general manager of Handyman Rescue Team: "If you remove your light fixture and you find a metal or plastic box, wiggle the box to test the screws. If it's not secure, you'll need to replace it. If it seems sturdy and sound, you can install a light fixture that weighs up to about 15 lbs (6.8 kg). However, if you're hanging a heavier fixture like a chandelier, you'll need to install a beam into the rafters above the ceiling and hang the box and the light from that."
Advertisement
Follow the instructions that came with the new fixture. Generally, you’ll need to line up the crossbar with the back of the canopy and thread the pipe or screws through the canopy. Only ¹⁄₄ to ¹⁄₂ inch (0.64 to 1.27 cm) of the pipe should extend past the canopy, so adjust the screws or pipe until that much is showing. Tighten the nuts to hold the screws or pipe in place.^{[3]XResearch source}
Ask someone to hold the fixture while you do this. First, make sure all the wires are on 1 side of the crossbar. Then, use a screwdriver to screw the crossbar to the electrical box on the ceiling. It should go across the center of the hole and be screwed in on either side.^{[4]XResearch source}
You should connect the “hot” wire in the fixture to the “hot” wire in the ceiling, and the neutral wire in the fixture to the neutral wire in the ceiling. Generally, the hot wire is black or red and the neutral wire is white. Use wire connectors to connect the like wires to each other. Simply twist the exposed parts of the wires together, then screw the connector onto the wires.^{[5]XResearch source}
There is a ground screw on the crossbar that you installed, and it can usually be found just to 1 side of the center of the crossbar. Find the ground wire, which is usually green or copper. Wrap the ground wire clockwise around the ground screw to tighten it.^{[6]XResearch source}
Tuck all of the wires and wire connectors into the electrical box. Then, use a screwdriver or impact driver to secure the canopy to the ceiling. You can adjust the threaded rod or screws, if necessary, to make sure the canopy fits securely.^{[7]XResearch source}
If necessary, place light bulbs into the sockets of the fixture. Make sure they are rated for the type of fixture you purchased. Then, flip the circuit breaker to turn the power back on.^{[8]XResearch source}

Method 2

Method 2 of 2:

Hanging a Swag Light from a Ceiling Hook

Download Article

1
Purchase a swag light and cord kit. Look for a “swag” light, which is one that is hung from the ceiling and plugged into a wall. This means you don’t have to do any electrical work! The lamp and cord kit should contain the light and shade, the cord with a plug, and anchors or hooks to install the light.^{[9]XResearch source}
- You can find swag lamps and cord kits at home improvement and home decorating stores as well as online.
2
Ensure the cord will reach an outlet. Before you add hooks or anchors, think about where you want the light to go. Determine if the cord is long enough to reach an outlet once you hang the light and run the cord along the ceiling, then down a corner where 2 of your walls meet. If it’s not, consider hanging the light somewhere else or adding an extension cord.^{[10]XResearch source}
- Running the cord down a corner, rather than the middle of a wall, makes for a more attractive project.
If the light you plan to hang is heavy, such as more than 5 pounds (2.3 kg), use an anchor rather than a hook to secure it to the ceiling. Situate this anchor or hook where you want the light to hang from and screw it into the ceiling. The other hook should go in the corner of the room in which you plan to run the cord down to the outlet.^{[11]XResearch source}
Remove all the packaging and screw the bulb into the socket, if necessary. Secure the lamp shade over the bulb and connect the cord, if applicable. Then, hang the cord from the hook or anchor you installed so the lamp sits at the desired height.^{[12]XResearch source}
Once you’ve gotten your light hung up, all that’s left to do is plug it in! If you want a cleaner look, consider covering the cord with cord covers. These are plastic tubes that conceal the cords and help them stay in place. Simply slip the cord into the tube through the slit in the back. Then, peel off the adhesive backing and stick the cover to the wall or ceiling.^{[13]XResearch source}

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Alternatively, you could hang string lights on the ceiling to provide both light and ambience.
Thanks
Helpful0 Not Helpful1

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

If your home was wired before 1985, make sure the fixture you buy doesn’t necessitate that your electrical wire is rated for 90 °C (194 °F).^{[14]XResearch source}
Thanks
Helpful0 Not Helpful0
If your new light fixture weighs more than 50 pounds (23 kg), you may need to install a new electrical box to hold it.^{[15]XResearch source}
Thanks
Helpful1 Not Helpful0
Aluminum wiring should not be altered. If you have aluminum wiring, which is dark gray rather than copper, contact a certified electrician to help you with this project.^{[16]XResearch source}
Thanks
Helpful0 Not Helpful0