How to Fix a Sinking Desk Chair

Office chairs use a pneumatic cylinder that controls the height of the chair through pressurized air. The cylinder on most chairs fails within a few years, typically because the seals are too damaged to maintain pressure. You can buy a replacement cylinder to restore full function to your chair, but this is nearly as expensive as buying a replacement. Try these simple DIY methods instead to fix your chair at one convenient height.

Method 1

Method 1 of 2:

Using a Hose Clamp

Download Article

Most office chairs have a plastic tube over the extendable cylinder. Slide this all the way down or up, until you can see the metal cylinder underneath.^{[1]XResearch source}
2
Set the chair to the preferred height. You will not be able to adjust the height after this repair, so make sure you have it right. The seat of the chair should be level with your knees when you are standing.
- If the chair won't stay up even when no one is on it, lay it on its side.
- If the plastic skirt covers the cylinder at this height, you will need to remove the skirt first. To do this, turn the chair upside down, push the retaining clip at the base with a screwdriver, and pull off the wheels, then the skirt. Slide the wheels back on.
Advertisement
Get a ¾" (2 cm) hose clamp (Jubilee Clip) from a hardware store. Loosen the screw on the hose clamp (Jubilee Clip) and pull out the belt end. Wrap the clamp around the metal cylinder, but do not tighten it yet.
4
Improve the grip of the clamp (recommended). The clamp will need to be very tight to hold the chair up. Give the clamp a better surface to grip by wrapping a strip of rubber or a couple layers of duct tape around the cylinder.^{[2]XResearch source} Do this at the highest visible point on the cylinder,
- Alternatively, scuff up this area of the cylinder with sandpaper.
- If the cylinder looks dirty or greasy, clean this off first.
Slide the hose clamp to the top of the cylinder. Double check that the chair is at the correct height. Pull the hose clamp tight and fasten it by rotating the screw.
6
Test the chair. The chair should now be unable to slide down past the clamp. The built-in height adjustment will still not work properly. If the chair is at the wrong height, move the clamp higher or lower on the cylinder.
- If the clamp slides off, fasten it over a strip of rubber to improve the grip, or try the PVC pipe method below.

Method 2

Method 2 of 2:

Using PVC Pipe

Download Article

1
Measure your chair's cylinder. Pull down the plastic skirt cover the extendable, metal cylinder. Estimate the diameter of the cylinder by holding a ruler across it horizontally. Also measure the length of the cylinder when the chair is at the perfect height.
- You shouldn't need an exact measurement, but you can calculate the diameter from the circumference if you prefer to be precise.
2
Buy a length of PVC pipe. This pipe will fit over the pneumatic cylinder of the chair. It should be about the same size as the cylinder diameter, or slightly larger. Pipe 1.5 inches (3.8 cm) in diameter works well for most models.^{[3]XResearch source} Buy enough straight pipe to extend from the wheel base of your chair to the seat, when the chair is at the preferred height.
- The pipe does not have to be in one piece. It may be easier to work with in smaller pieces, although you can easily cut it yourself at home.
- One user reports using a tall stack of plastic shower rings instead of PVC pipe. These are even cheaper and easier to install, but they may not be sturdy enough to support your weight. Try at your own risk.
3
Saw through the PVC pipe lengthwise. Secure the pipe in a vise. Use a hacksaw or back saw to cut through the pipe from tip to tip, but only on one side. The end result should be a pipe with a slit in it, not two half-pipes.
- Wearing a mask or respirator is recommended while cutting PVC to avoid inhaling irritating particles.^{[4]XResearch source}
- If you do not have a vise or cutting tools, just leave the pipe intact and remove the chair's wheels so you can slide on the pipe. In most cases, you can remove the wheel base by pressing a retaining clip on the underside with a screwdriver.
4
Snap the pipe onto the chair cylinder. Pull the chair's plastic skirt up or down to reveal the metal cylinder. Push the slit side of the PVC pipe against the cylinder to snap it around the cylinder. It should now hold the chair in place, preventing it from sliding down.
- If you're having trouble snapping the pipe on, saw it into shorter pieces and try again.
Add more pipe to adjust the height of the chair. If the chair is still too low, raise it and snap on another piece of pipe. You will not be able to lower the chair again without removing the pipe, so make sure you set it to the perfect height.

Community Q&A

Search

Add New Question

Question
What can I do to repair a reclining sofa? It has a "kick" release and catch under the seat.
Community Answer
You'll have to take the bottom of the sofa off to access the mechanicals. Then, you can reinstall or replace what's broken or has come loose.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 23 Helpful 21
Question
How do I keep a chair low or "sunk?"
Community Answer
If you want it fully sunk and need it to stay there. Then, your only choice is to drill a hole in the cylinder and ensure it can't buildup nor maintain any pressure. In the future, if you or someone else wants to raise the seat the hose clamp(s) can be installed or even halved pieces of pipe can be held in place by 2 hose clamps or screws or rivets drilled into the cylinder.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 59 Helpful 28

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Read Video Transcript

Things You'll Need

Hose Clamp Method

Hose clamp (Jubilee Clip) about ¾ inch (2cm) across and long enough to circle the chair's cylinder
Sandpaper, strip of rubber, or duct tape
Cleaning product or degreaser (optional)
Screwdriver (sometimes)

PVC Pipe Method

Ruler or tape measure
PVC pipe a similar size to your chair's cylinder
Hacksaw, band saw, or PVC cutting tool
Vise

Reader Videos

Tips

You can also buy a replacement pneumatic cylinder for your chair. However, the cylinder often costs nearly as much as a new chair, and can be tedious and difficult to install.
Thanks
Helpful5 Not Helpful3
You can spend a little more money to buy a "chair saver kit" online instead. This is a collection of clip-on clamps that work the same way as these DIY materials.
Thanks
Helpful6 Not Helpful7

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Do not attempt to secure the chair by drilling into the cylinder and installing a bolt. The cylinder contains pressurized air which may release violently if you puncture the cylinder.
Thanks
Helpful16 Not Helpful2