Download ArticleDownload ArticleX
This article was co-authored by David Balkan. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award.
There are 8 references cited in this article, which can be found at the bottom of the page.
This article has been fact-checked, ensuring the accuracy of any cited facts and confirming the authority of its sources.
This article has been viewed 2,775,606 times.
Most private septic systems are made up of two parts: the holding and digesting tanks, and the dispersal field.[1] As the first holding tank fills up, the liquid waste will transfer to the second tank. Once the second tank fills with liquid, it will disperse into the soil below it. The system shown here is a small system, designed for limited use by two people with no laundry. The tank is much smaller than required by building codes, and the design is missing some important items such as internal baffles and a qualified site assessment. This system uses two 55 US gal (210 L) drums, as opposed to the 1,000–2,000 US gal (3,800–7,600 L) tanks used for a standard home septic system. The system also has a dispersal field about one third that of a large home.
Property owners planning a system similar to this one should be aware that this system would not pass inspections from any public health department in the USA and could subject the owner to a fine if the system was discovered in use.[2] On the other hand it is better to safely dispose of waste than not to. Today's water-saving toilets use less than two gallons per flush. This system will handle such a load. For people living in places without septic treatment, it could be a lifesaver.
Steps
Cut a hole in the top of each drum that’s the same size as the toilet flange’s outside measurement. Measure the outside diameter of the toilet flange you’re using. Place the hole against the edge of the drum so you can easily connect them to pipes. Use a saber saw to cut through the drums.
Attach a 4 in (10 cm) toilet flange to each hole. Push the flanges into the top of each tank so they fit flush. Screw the flanges into the tanks so they don’t move or shift after you place them.Advertisement
Cut a 4 in (10 cm) hole in the first drum on the opposite side as the hole in the top. Place the hole about 4–5 inches (10–13 cm) down from the top of the drum and make sure it lines up with the hole on top of the tank. Cut the hole with a saber saw or a hole saw.
Cut 2 holes in the side of the drum at 45-degree angles from the center of the hole on top. Find the center line running through the middle of the hole on top of the drum. Make 45-degree angles from either side of the centerline and mark it on the second drum. Use a saber or hole saw to cut through the side of the barrel and make your holes.
Advertisement
Dig a trench that’s 4 × 26 × 3 ft (1.22 × 7.92 × 0.91 m). Use either a shovel or an excavator to make a hole in the spot where you want your tank. Keep digging until the hole is 4 feet (1.2 m) wide, 26 feet (7.9 m) long, and 3 feet (0.91 m) deep.[3]- You can usually rent excavators for digging from a heavy machinery supply store. Check for equipment rentals online.
Place the drum with 1 side hole at the end of the trench. Make sure the drum is level when you set it down. Check that the top of the drum is at least 4 inches (10 cm) below the surface.
Dig a hole 1 ft (30 cm) deeper for the placement of the second drum in front of the first. Make your hole the same diameter as the drum you’re placing in it so it has a tight fit and doesn’t move around.
Level the hole with gravel until the 90-degree bend fits from the hole in the side of the top drum to the toilet flange of the lower drum. Dry-fit the 90-degree bend between the 2 drums to see if the holes line up well. Dig the hole slightly deeper if you need to make the pipe line up better.
Cut 3 1⁄2 and 2 1⁄2 in (8.9 and 6.4 cm) pieces of 4 in (10 cm) ABS pipe and glue them onto the bend. Cut the ABS pipe pieces, or nipples, with a hacksaw. Fit the pieces into the bend and use PVC glue to secure them in place.
Test the fit for alignment between the two drums. Fit the end of the 2 1⁄2 in (6.4 cm) nipple into the side hole on the first drum. Make sure the nipple on the other end lines up with the hole on top of the second drum.
Glue the end of the 3 1⁄2 in (8.9 cm) nipple into the toilet flange on the second tank. Use PVC glue to secure the bend in place. Don’t worry about the connection to the first drum yet since you’ll connect it later.
Glue a Y-bend to a 3 1⁄2 in (8.9 cm) nipple and add a 45-degree bend to the angled portion of it. Use your PVC glue to secure a nipple to the end of the Y-bend. Align the angled pipe on the Y-bend so it meets the incoming waste line, and glue it into the toilet flange.
Cut and glue 2 1⁄2 in (6.4 cm) nipples to one end of the 45-degree bends at and insert them in the side of the lower drum. Point the ends of the 45-degree bends so they’re perpendicular to the bottom of the trench.
Advertisement
Pound a stake into the ground so that the top of the stake is level with the bottoms of the 45-degree bends. It doesn’t matter what kind of stakes you use. Drive the stakes into the ground using a mallet or a hammer.
Tape a 1 in (2.5 cm) wide block to the end of a 4 ft (1.2 m) level. This will help make sure you create sloped drain pipes so your tanks can empty out.
Place another stake about 3 7⁄8 ft (1.2 m) down the trench from the first one. Use your hammer or mallet to drive the stake down until it’s the same height as the first.
Lay the end of the level without the block on the first stake and the block on the second. Pound the second stake down until the level is balanced. The second stake is now 1 inch (2.5 cm) lower than the first, or 1⁄4 inch (0.64 cm) lower per 1 foot (30 cm).
Repeat this process until you have stakes the length of the trench. Continue adding stakes down the rest of the trench every 3 7⁄8 feet (1.2 m) from the last one so the stakes slope away from the drums.
Place gravel in the trench until the top of the gravel is level with the top of the stakes. The gravel will now slope away from the drums at 1⁄4 inch (0.64 cm) per 1 foot (30 cm) of horizontal distance.
Place 20 ft (6.1 m) of perforated drain pipe onto each hole on the second drum. Slide the ends of the drain pipes into the 45-degree bends on the lower drum. Make sure the holes in the pipes face down so liquids can soak back into the ground.
Check the pipes with the level to see if the 1⁄4 in (0.64 cm) grade is consistent along the length of the pipe. Adjust the slope by adding or removing gravel under the pipe.
Seal the 45-degree and 90-degree bends to the lower and upper drums, respectively. Use a 2-part epoxy or silicone caulk for the best seal on your drain pipes. Try using flex pipe for this, so that if the ground shifts it will give a little.
Fill the lower drum with water to prevent it from collapsing under the weight of the gravel. Bury the trench to the top of the bottom drum with the remaining gravel.
Lay landscape fabric over the gravel. This will prevent the soil from seeping into the gravel and ensure that you maintain good drainage on your tanks.
Fill the remaining trench area with soil, compacting well to the original grade. Make sure the ground is level when you finish filling in the area with your soil. Leave the top pipe from the first tank exposed so you can easily access the tanks if you need to drain them later.
Fill the upper drum with water. Pour the water directly down the exposed pipes from the top drum. Continue filling the drum until it’s full and place a cap on top to seal it.[4]
Advertisement
Community Q&A
Search
- QuestionWhat is considered low usage?
Community AnswerLow usage is under 125 gallons per day. - QuestionWhat is the purpose of the 'y' elbow on the first tank? Is that left open or sealed when completed? If left open, won't it stink?Community AnswerThat's your clean out, it takes a threaded cap or plug.
- QuestionHow much water do you fill it with?Community AnswerThe key word is "fill." Continue to place water into the drum until the level no longer increases.
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
SubmitAdvertisement
Video
Tips
- Instead of a 90° elbow, you should put two of them together, to form a U. That way the end that's in the first barrel will be pointing towards the bottom of the tank. Add a short section of straight pipe to this, extending it a few inches deeper towards the bottom. Solids either float or they sink. They don't stay around the middle. This way, the solids don't ever make it to the second tank, only the broken down liquid waste. The same should be done for each of the drainage pipes coming from the second barrel. Just to make absolutely sure that no solids make their way into the world leach field.Thanks
- 30% of the waste goes down in the ground and 70% is evaporated by sunlight. Don't compact the soil since it messes up the evaporation process.Thanks
- The horizontal side of the "Y" connects to the waste source, and should be fitted with a connector that fits the source supply line.Thanks
Tips from our Readers 
The advice in this section is based on the lived experiences of How.com.vn readers like you. If you have a helpful tip you’d like to share on How.com.vn, please submit it in the field below.
- If you regularly use a septic system treatment (like RID), it will help keep the tank from needing to be pumped so often.
- Try to use toilet paper as little as possible. In my home, I bag all my toilet paper except for the very dirty pieces.
Submit a Tip
All tip submissions are carefully reviewed before being published
Thanks for submitting a tip for review!
Advertisement
Warnings
- Don't drive over the area that contains the drums.Thanks
- This is a very small capacity system. This is not designed to meet the needs of a large household.[5] It is designed for a small travel trailer and two people. To maximize the life of this mini system, do not put anything in the septic system except water, human waste, and toilet paper. Otherwise, you may have to pump the upper drum once a year or so. The system shown here only needs to be pumped twice in 5 years.[6]Thanks
- Follow local Septic Regulations when constructing a septic system. It is illegal to install a septic system without a permit. The permit will detail the local requirements for installation of a septic system.[7]Thanks
- Don't place your septic system too close to trees, as tree roots will grow into your line, and cause them to clog and with time, cause harm to your system.[8]Thanks
Advertisement
Things You'll Need
- 9 cubic yards (6.9 m3) of 3/4 or 1 1/2 crushed rock or blue metal
- 80 square feet (7.4 m2) of landscape fabric
- 2 plastic drums that are 55 US gal (210 L)
- 10 feet (3.0 m) of 4 in (10 cm) ABS plastic pipe
- 4 in (10 cm) ABS 90-degree bend
- 4 in (10 cm) ABS Y-bend
- 3 ABS 45-degree bends with 4 in (10 cm) diameters
- 40 feet (12 m) of 4 in (10 cm) perforated drain pipe
- 2 drain pipe couplers with 4 in (10 cm) diameters
- 2 toilet flanges with 4 in (10 cm) diameters
- Level
- 10 wood Stakes
- PVC glue
- Two-part epoxy or silicone sealant
- Wood block that’s 1 in (2.5 cm) thick
- Duct tape
- 4 in (10 cm) ABS removable cap
Expert Interview
Thanks for reading our article! If you’d like to learn more about construction tips, check out our in-depth interview with David Balkan.
References
- ↑ https://www.epa.gov/septic/how-your-septic-system-works
- ↑ https://www.tn.gov/environment/permit-permits/water-permits1/septic-systems-permits/ssp/permit-water-septic-system-construction-permit.html
- ↑ https://www.youtube.com/watch?v=uX-pvPDl9T4
- ↑ https://extension.missouri.edu/publications/wq402
- ↑ https://www.epa.gov/septic/types-septic-systems
- ↑ https://extension.missouri.edu/publications/eq401
- ↑ https://www.cardinia.vic.gov.au/info/20051/building/22/get_a_permit_for_a_septic_system#section-7-enquiries
- ↑ https://doh.wa.gov/community-and-environment/wastewater-management/septic-system/caring-your-system
About This Article
Professional Plumber
This article was co-authored by David Balkan. David Balkan is a Professional Plumber, CEO of Balkan Sewer and Water Main Service, and President of Balkan Sewer and Drain Cleaning. As a hands-on owner of these companies for over 40 years, David is knowledgeable about water service lines, sewers, and drain line issues. David is a Committee Chairman of the Master Plumbers Council and has sat on the Executive Committee of the Sub Surface Plumbers Association of New York for over 30 years. His knowledge and solution-oriented approach contributed to Balkan Sewer and Water Main Service being the largest and most trusted service in New York City and the recipient of the 2017 Angie’s List Super Service Award. This article has been viewed 2,775,606 times.
Co-authors: 57
Updated: January 4, 2024
Views: 2,775,606
Categories: Waste Removal Systems
Thanks to all authors for creating a page that has been read 2,775,606 times.
Reader Success Stories
"Well, I was hunting knowledge and now I know. The next step is to put the plan into action!"
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
Advertisement
