How to Calculate Amount of Paint to Paint a Room

How much paint do I need? This age-old question is an important one—after all, you don’t want to run out of paint in the middle of a house painting project, but you also don’t want to have a huge container of paint leftover when everything’s finished. Don’t worry. With just a tape measure and a calculator, you can calculate the exact amount of paint you need in a matter of minutes. We’ve outlined the exact formula you need to get the job done so you can complete your project as efficiently as possible.

1

Measure the length of each wall.

Download Article

Wall length helps you figure out total square footage. Grab a tape measure and place it flush along one end of the wall. Check that the tape measure is firmly in place, and then pull it in a straight, taut line lengthwise across the wall. To be safe, do a couple of measurements to make sure your calculations are totally accurate. Then, measure the length of all the other walls in your room.^{[1]XResearch source}
- It may help to ask a friend to hold the measuring tape in place while you pull it across the wall.

2

Calculate the height of each wall.

Download Article

The total height is the other part of your square footage equation. Anchor your tape measure at the bottom edge of the wall and slowly pull the tape measure upward, keeping it flush against the wall as you extend it. Jot down the measurement once the tape reaches the edge of the ceiling. Then, check the height of all the other walls to make sure your measurements are exact.^{[2]XResearch source}
- You may need to use a stepstool or ladder to measure the entire height of the wall. Don’t be afraid to ask a friend for help if you need it!
- All of your height measurements might be the same, depending on the size and shape of your room.
- Don’t include the trim in your measurements—you’ll be calculating that separately.

3

Multiply the total length by the height for each wall.

Download Article

Length times height gives you the total surface area of your walls. Find the area of each individual wall, jotting down the area for each one. There’s a chance that your walls are all different sizes, so doing individual calculations helps you get more accurate results.^{[3]XResearch source}
- For example, if a wall is 15 ft (4.6 m) and 10 ft (3.0 m) tall, the total surface area would be 150 sq ft (13.94 m²).

4

Add all of the square footages together.

Download Article

Plug all of the surface areas you just calculated into a calculator and see what the total surface area comes out to. This isn’t the exact amount of surface you have to paint—it’s just a starting point!^{[4]XResearch source}

5

Measure the area of each door and window.

Download Article

Multiplying length by width gets you this number. Use your tape measure to figure out the length and height of all the windows in your room, as well as the length and height of any doors. Then, multiply the measurements for each individual structure together to get the total surface area of each structure.^{[5]XResearch source}
- If all of your windows and doors are the same size, you only need to measure them once—but you still need to multiply by the total number of structures that you have. For example, if you have 3 windows that have a total surface area of 17 sq ft (1.6 m²), you’d multiply that by 3 (giving you a total of 51 sq ft (4.7 m²)).

6

Subtract each door and window from the total.

Download Article

Let’s say your walls’ total surface area is 576 sq ft (53.5 m²), and there are 2 windows that are each 15 sq ft (1.4 m²) and a door that’s 20 sq ft (1.9 m²). Subtract the 50 sq ft (4.6 m²) of doors and windows from the original 576 sq ft (53.5 m²), which gives you a total of 526 sq ft (48.9 m²) to paint.^{[6]XResearch source}

7

Double the total square footage if you plan on painting 2 coats.

Download Article

Your square footage calculation only counts for 1 coat of paint. Chances are, you’re probably giving your walls at least 2 coats of paint for a polished, long-lasting look. For each extra coat of paint, add the total surface area to your final calculation.^{[7]XResearch source}
- If your total wall surface area is 650 sq ft (60 m²) and you plan on adding 3 coats of paint, you’d need enough paint for 1,950 sq ft (181 m²) of wall space.
- You may need extra coats of paint if you’re repainting dark walls with light-colored paint.

8

Divide the total square footage by 350 to 400.

Download Article

This helps you figure out how much paint you need. A single gallon of paint can cover about 350 to 400 sq ft (33 to 37 m²) of wall space. So, dividing your total square footage by 350 to 400 gives you an accurate idea of how many gallons of paint you’ll need for your project.^{[8]XResearch source}
- Paint Calculation Formula: Surface Area / 350 = gallons of paint needed or Surface Area / 400 = gallons of paint needed
- If you’d rather err on the side of caution, divide your total square footage by 350 rather than 400. That way, you’ll have a little extra paint on hand if the project ends up being bigger than you expect.
- If you have 1,600 sq ft (150 m²) of wall space to paint, you’d need 4 to 4.75 US gal (15.1 to 18.0 L) to paint your space.
- If your walls are textured or completely unpainted, divide your total square footage by 250 sq ft (23 m²) instead. These surfaces tend to use more paint than regular, smooth walls.

9

Round up the nearest quart.

Download Article

A little extra paint is good, but you don’t want too much leftover. Chances are, you won’t get an exact number of gallons or liters; instead, it’ll be a decimal. Rather than rounding up to the next whole number (gallon), round up to the next quarter (quart) instead.^{[9]XResearch source}
- If you need 4.44 US gal (16.8 L) of paint to cover your wall space, you’d round it up to 4.5 US gal (17 L) instead.

10

Calculate the total amount of paint for trim.

Download Article

Multiplying the width and length gets you the total square footage. Grab your tape measure and take down the exact width and length for each individual section of trim. Multiply the length and width of each individual section together, and then add up all the sections to get your total surface area. Then, divide the surface area by 350 to 400 to get the amount of paint you need in gallons.^{[10]XResearch source}
- Let’s say the sections of trim are 30 sq ft (2.8 m²), 40 sq ft (3.7 m²), 60 sq ft (5.6 m²), and 25 sq ft (2.3 m²). The total square footage would 155 sq ft (14.4 m²); divided by 400, you’d get 0.38 US gal (1.4 L). To be safe, you’d round up to 0.5, giving you a total of 0.5 US gal (1.9 L).

Amount of Paint Calculator

Sample Paint Calculator

Expert Q&A

Search

Add New Question

Question
Is 1 gallon of paint enough for a room?
Varga Gulshani
Residential Painting Specialist
Varga Gulshani is a Residential Painting Specialist and the Owner of Elegant Painting based in Washington. With more than 16 years of experience, Varga and his team specialize in residential interior painting, exterior painting, and cabinet painting. Varga and the Elegant Painting team have all received background and verification checks.
Varga Gulshani
Residential Painting Specialist
Expert Answer
Estimating accurately how much paint you'll need is hard, especially because it depends on the tint base. Almost all colors require two coats, but some ultra-deep bases might need three to four coats. As a general rule, you'd need 2 gallons for an average-sized bedroom.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 7 Helpful 6
Question
Can I measure the length, width and the height to get my accurate measurement?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
You only need to measure height and length to get the surface area of your walls. However, you only use width and length when measuring for trim.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 5 Helpful 1
Question
How to calculate the area of a room with door and window
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
Measure the length and width of each door and window. Then, multiply these measurements to get the total surface area of each structure. Subtract these measurements from your total wall area to figure out how much surface you need to paint.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 1

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Multiply the height and length of the ceiling if you’d like to paint that surface, too. As a general rule of thumb, 1 US qt (0.95 L) provides enough coverage for 100 sq ft (9.3 m²) of space, but you may need more if you plan on adding another coat.^{[11]XResearch source}
Thanks
Helpful0 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!