How to Bridge an Amplifier

Download Article

Two-Channel Amps

|

Four-Channel Amps

|

Video

|

Expert Interview

|

Expert Q&A

|

Tips

|

Warnings

Bridging an amplifier combines the available channels into one channel with half the ohm (Ω). It is commonly used in car stereo systems, allowing a powerful mono signal to be sent to a subwoofer.

Method 1

Method 1 of 2:

Two-Channel Amps

Download Article

1
Make sure your amplifier can be bridged. This should be indicated on the documentation pamphlets that came with the amplifier, or the amplifier itself. If the amplifier is used, or lacks documentation, go online and check for the specifications on the manufacturer's website.^{[1]XResearch source}
- Bridging an amplifier cuts the resistance load (measured in ohms) in half, which can cause it to overheat. Be sure to check your manual (or the manufacturer’s website) to see if once connected to a speaker, whether or not your amplifier can function at half the ohms it currently uses.
- Most amplifiers have a small diagram near the channels indicating the terminals you would use to bridge it. If your amplifier does not claim to be able to bridge, don't try to bridge it. It may already be bridged internally, and you could cause damage to your amplifier.
- Be aware of the fact that if your amplifier is a stereo amplifier (amplifying both left and right), bridging it would cause it to become a mono amplifier (amplifying from one; either the left or right).
2
Know the layout of your equipment. On your two-channel amp, you should see 4 terminals: a positive (+) and a negative (-) for channel 1, and a positive (+) and a negative (-) for channel 2. Each terminal will be labeled as follows:^{[2]XResearch source}
- Channel 1
  - "A" (positive)
  - "B" (negative)
- Channel 2
  - "C" (positive)
  - "D" (negative)
Advertisement
3
Connect the amplifier to one speaker. From the wires coming out of the speaker, connect the positive speaker lead to terminal A (the positive for channel 1) and connect the negative speaker lead to terminal D (the negative for channel 2). Connect these wires by unscrewing the screw in that terminal, placing the wire in between the top and bottom portions of the terminal, and then screw the screw down tightly to secure the wire.^{[3]XResearch source}
- The wires coming from the speaker are going to be insulated with a plastic coating. You will need to strip off a small portion of the wire insulation (less than 1 inch) using a pair of wire strippers in order to secure it to the terminals.^{[4]XResearch source}
- What this connection does is it combines the power from the two separate channels, doubling your power output.^{[5]XResearch source}

Method 2

Method 2 of 2:

Four-Channel Amps

Download Article

Just like method 1, you must figure out if your four-channel amplifier can be bridged. Taking all the same precautions, be sure to consult the amplifier manual or research your amp model online to be sure it can be bridged.^{[6]XResearch source}
2
Know the layout of your equipment. On your four-channel amp, you should see 8 terminals: channels 1 through 4 each have a positive (+) and negative (-) terminal. Each terminal will be labeled as follows:
- Channel 1
  - "A" (positive)
  - "B" (negative)
- Channel 2
  - "C" (positive)
  - "D" (negative)
- Channel 3
  - "E" (positive)
  - "F" (negative)
- Channel 4
  - "G" (positive)
  - "H" (negative)
3
Connect the amp to the first speaker. From the wires coming out of the speaker, connect the positive speaker lead to terminal A (the positive for channel 1) and connect the negative speaker lead to terminal D (the negative for channel 2). Again, just like bridging a two-channel amplifier, connect these speaker wires to the amplifier by unscrewing the screw in that whichever terminal you are connecting the wire to, place the wire in between the top and bottom portions of the terminal, and then screw the screw down tightly to secure the wire.
- Once the wires are secured, the first speaker is connected to the amplifier.
Following the previous method, again take the wires coming from the second speaker, but this time, connect the positive speaker lead to terminal E (the positive for channel 3) and connect the negative speaker lead to terminal H (the negative for channel 4).

Expert Q&A

Search

Add New Question

Question
How do I bridge a subwoofer in a car?
Steven Racz
Audio Video & Automation Expert
Steven Racz is an Audio Video & Automation Expert and Owner at Altitude Audio Video based in Littleton, Colorado. With over 15 years of professional experience, Steven and his team of technicians specialize in installing residential and commercial audio systems, theater design and installation, Josh Ai voice & control systems, and Control4 automation. At Altitude Audio Video, they strive to tailor the perfect system for your needs.
Steven Racz
Audio Video & Automation Expert
Expert Answer
So if you have two subwoofers and a four-channel amp, four channels can be bridged to two channels. Another example is that if you have a two-channel amp with one subwoofer, you could bridge both of the channels for one subwoofer. Typically, the amp will stay on it and be bridgeable, meaning that you'll use one positive and one negative from the two different channels being brought into one.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 1
Question
How can I play two speakers on one amp using bridged mode?
Community Answer
You will need a 4 channel amp to run 2 speakers in bridged mode. Typically the speakers will be hooked to the positive side of one channel and the negative side of another thus bridging the channels, but this is not always the case. Look for the diagram near the speaker connects to see how yours is bridged. Once the speakers are hooked up, there will be a switch marked Stereo, Mono, or Bridged. Set this to Bridged.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 16 Helpful 32
Question
Can I connect one dual-coil speaker to a four-channel amplifier?
Community Answer
Surely - this is possible. Simply handle the two voice coils like they were from two separate speakers. (And like the description of "Method 2".) Don`t interchange their connections (+ of one vc to - of another). But beware: you'd better feed the four channels with the same signal (which means: all inputs fed from the same source,mono, not stereo), and surely not 4 different signals ("quadrophonic"), to get best results. Treat the voice coil's terminals as they're marked, + as +, - as -.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 10 Helpful 19

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Before trying to connect anything, you can quickly and easily consult an electronics or car audio store.
Thanks
Helpful8 Not Helpful14
Try to stay one level above the amplifiers lowest rated resistance. For example, if your amplifier says that it can handle 2 Ohms, wire it so it produces 4 Ohms. If you go lower than its displayed lowest rated resistance, your amp could shut off.
Thanks
Helpful5 Not Helpful12