How to Wind a Watch

Most modern wrist watches are quartz, which run on batteries. Traditional mechanical watches, small fashion watches, or "vintage" watches are powered by a spring mechanism. The spring tightens as you wind it and drives the watch as it unwinds. This mechanism keeps the wristwatch in time. There are two types of mechanical movements: manual and automatic.

Method 1

Method 1 of 3:

Winding a Manual Movement Watch

Download Article

1
Lay the wristwatch on a table. Remove the wristwatch from your arm or storage. If you wind a watch while it is on the arm, with the watch tight against the skin, the winding motion may not be effective.
- Winding a watch while attached to your arm places strain on the mechanics in the watch because of the angle on your arm and the stem.
- Locate the stem, which will be pulled out to wind the watch. The stem is a small dial on the side of the watch.
Reverse the position, if you are left-handed. The stem may have several settings, including settings for time, calendar, alarm, or time zone. The settings are located at little "clicks" as you pull the stem out or push it in. Use trial and error to feel the clicks and identify the winding position.
Advertisement
Use your thumb and index finger to carefully pull out the watch stem by the stem's top or "crown." This can be difficult because you do not want to over-wind the mechanism.
4
Wind the watch’s stem. You should wind the watch clockwise until you feel resistance. Be conservative and don’t keep turning once you feel resistance. You can damage the watch if you continue to wind the stem past resistance. In time, you will develop a feel for the resistance.
- If the watch runs down sooner than you like, you know you did not quite hit the maximum tension.
- Depending on the size of the watch, 20 to 40 forward turns should lead to resistance; over-winding will strain or break the mechanism.
Press the crown to return stem to its place. Be careful to put the watch’s components back exactly as you started. Never shove or force parts when handling the stem and crown of a watch.

Method 2

Method 2 of 3:

Setting an Automatic Movement Watch

Download Article

1
Research your watch. Sometimes manual movement watches can last up to five days with one wind. This doesn’t mean your watch operates on automatic movement. Check the packaging details or research the serial code online to find out more info. You can always wait to see how long your watch lasts from one wind.
- If it is an automatic movement watch, the watch will operate for a long time. The automatic movement will lose wind if it is not worn regularly.^{[1]XResearch source}
2
Prepare your watch. Take the watch off your wrist to properly set the wind. It is important that you be cautious when handling the stem of the watch. The stem is connected to several important mechanisms inside your watch that you don't want to break.
- Fiddling with the stem of your watch while it's attached to your arm could bend or damage it.
3
Locate the crown. Automatic movement is similar to a manual movement watch, except that it is powered by a rotor which maintains the watches energy. The crown should also set the time, date, or other function on your watch. Like a manual movement watch, you’ll need to pull the crown out to expose the stem.
- A good way to test what each level of the stem does is to test each one. The level that winds the watch shouldn’t appear differently on the outside.
4
Wind the crown. Once you’ve determined which level of the stem affects the wind, you’re ready to set your watch. Twist the crown clockwise until you feel resistance. It’s important not to go past the point of resistance on your stem.^{[2]XResearch source}
- You can break mechanical bits in your watch if you twist too far. Go to a watch specialist if you’ve twisted the stem too far.
Once you’ve wound the watch, you can set the time and other functions. Check the face of your watch to be certain which components you’re affecting. Use a digital watch to set an accurate time and date.

Method 3

Method 3 of 3:

Caring for Your Watch

Download Article

1
Wind the watch daily. A wound watch will run accurately from 18 to 36 hours - depending on the mechanism. Larger watches have larger mechanisms. Smaller watches have smaller, more delicate mechanisms.
- Mechanical watches should be wound at least weekly, even if they are in storage.
- It might become routine if you wind the watch when dressing in the morning or before bed.
2
Clean your watch. You don’t need to purchase specialty oils or cleaners to care for your watch. Clean your watch with a toothbrush and warm water. Dip the toothbrush in the warm water and wipe off the bristles to remove excess water. Scrub the exterior and inside the stem with the toothbrush.^{[3]XResearch source}
- Don’t use too much force when cleaning inside the stem and crown.
- Don’t remove the screws and attempt to clean the gears, unless you know how to. Consult a watch specialist about cleaning the inside of your wristwatch.
3
Store your watch properly. Watches are delicate instruments and you should be cautious when putting one away in storage. The best way to protect your watch is by wrapping it in a protective coating. This could be bubble wrap or another packaging protective fabric.
- You should store the watch in an environment that is cool, clean, and dust free. Keep the watch out of direct sunlight.^{[4]XResearch source}
- You should attempt to wind it every week while in storage.

Expert Q&A

Search

Add New Question

Question
I haven't wound my watch in a long time, how do I properly wind an old unused watch?
Bill Green
Jewelry & Watch Expert, Designer, Gold, Silver, and Platinum Smith.
Bill Green is an Expert Jeweler and Appraiser. He is also the Founder & Creative Director of Jewelry & Timepiece Mechanix, and the Founder and Designer of Amaroo Handmade Opal Jewelry, based in Haddonfield, New Jersey. With over 40 years of industry knowledge, he and his team are known for restoring everything from new watches to vintage jewels and being one of the few shops that still design and make jewelry and watches. Jewelry & Timepiece Mechanix is part of the American Society of Jewelers and Gemologists and Ethical Metalsmiths. Bill studied at the Miami Jewelry Institute and the Gemological Institute of America as well as apprenticed with many accomplished craftspeople.
Bill Green
Jewelry & Watch Expert, Designer, Gold, Silver, and Platinum Smith.
Expert Answer
To revive a dormant watch, start by gently turning the crown clockwise, about 50 times. This action gradually energizes the mainspring, propelling the watch into motion. The initial winds serve to kickstart the mechanism, but it's around the 50th wind that the mainspring reaches its optimal tension for accurate timekeeping. Once you've completed the winding process, the watch should be ready to wear. As you go about your day, the automatic movement system will do its job. Simply wearing the watch and engaging in everyday activities, such as talking with expressive hand gestures or walking, will naturally keep the watch wound. It's akin to regularly refueling a tank, ensuring the watch remains powered and precise.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0
Question
While winding a watch, does the watch time change?
Community Answer
For my watch, the time doesn't change. I turn the crown without pulling it out. I can hear it click as it winds up.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 6 Helpful 34
Question
How do I unwind and over-wound watch?
Community Answer
Go to a watchmaker, because you can't do this yourself.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 4 Helpful 11

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Some watchmakers and collectors put the watch to their ear to listen to the mechanism click. This is easier and more pronounced on larger watches.
Thanks
Helpful0 Not Helpful2

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!