How to Use a Shark Steam Mop

Shark steam mops promise a fast and thorough clean, but how do you use one for the best results? Cleaning your floors with a Shark steam mop is a breeze—all you need is water and an outlet. We’ve put together a handy guide to using a Shark steam mop, including instructions on putting the mop together and choosing the right mop setting for your floors. If you’re ready to have sparkling clean floors, keep scrolling!

Method 1

Method 1 of 2:

Assembling the Mop

Download Article

1
Attach the handle to the body of the steam mop. First, slide the handle into the opening on the mop, making sure to push it past the line on the handle. Keep pushing until you hear or feel the handle click into place.^{[1]XResearch source}
- On some models, there is a large attachment screw that holds the handle in place. Use a flathead screwdriver to twist the screw until it’s firm.^{[2]XResearch source}
- Consult your user manual for assembly instructions that are specific to your model.
2
Put a cleaning pad on the mophead. Use the lavender loop on the side of the cleaning pad to slide the pad over the mophead. Then use the fasteners around the mophead to keep the pad in place. Once the pad is locked in, snap the mophead into the base of the mop.^{[3]XResearch source}
- Make sure the cleaning pad is attached striped-side down. Both sides can be used for cleaning, but there is only one way to correctly put it on.^{[4]XResearch source}
- Put the cleaning pad on while your steam mop is turned off.
Advertisement
3
Fill the water tank with distilled water. While the mop is unplugged, pull or twist the cap on the water tank to open it. Then fill the included measuring cup up to the line with distilled or soft tap water and pour it into the tank. Replace the cap to finish assembling your shark steam mop.^{[5]XResearch source}
- Distilled water reduces mineral buildup that can clog the steam nozzle or leave streaks on the floor while you clean.
- Make sure not to overfill the mop or it will start dripping onto your floors while you use it.
- Only fill the tank with water. Cleaning chemicals, scented perfumes, or even vinegar might damage the mop.^{[6]XResearch source}
- If your model has a removable water tank, make sure it’s securely snapped back into place before you begin mopping.

Method 2

Method 2 of 2:

Steam Mopping the Floor

Download Article

1
Sweep or vacuum the floor before steam mopping. Remove as much loose dust and dirt as possible so the steam mop can work its best. The mop might scratch your floor if there’s too much debris on it, or the water might mix with dirt and spread over the floor.^{[7]XResearch source}
- If you’re mopping tile floors in moisture-heavy rooms like the bathroom or kitchen, wipe away any surface grime on the tiles or grout beforehand to make your cleaning pad last longer.^{[8]XResearch source}
2
Plug the mop in to turn it on. Pull the wound-up power cord out of the mop and plug it into a 120-volt outlet. The on/standby button will start flashing blue. The mop only takes about 30 seconds to fully heat up.^{[9]XResearch source}
- Since the mop heats up so quickly, wait until you are 100% ready to begin mopping before plugging it in.
3
Choose a mop setting for the type of floor you’re cleaning. Use the on/standby button to select the dust, mop, and scrub settings. Once you choose a setting, the button will change from blinking to solid. Choose between:^{[10]XResearch source}
- Dust (light cleaning and dusting): This setting lifts light dirt and sanitizes the floor. Use this setting for laminate, bamboo, hardwood, or marble floors. Press the on/standby button once to activate.
- Mop (everyday cleaning): Choose "mop" to clean and sanitize small messes and heavily trafficked floors. This setting is meant for hardwood, marble, tile, and stone. Press the on/standby button twice to activate.
- Scrub (deep cleaning): Select "scrub" to sanitize floors and remove tough messes and stains on tile, stone, linoleum, or carpet (with a carpet glider attachment). Press the on/standby button three times to activate.
- To clean hardwood, use a highly absorbent microfiber cleaning pad to keep the floors dry. Don’t add any cleaning chemicals that might break the protective seal on the floorboards. The dust setting is safest.^{[11]XResearch source}
4
Mop the floor with forward and backward motions. Pump the handle to dampen the cleaning pad, then push the mop back and forth in small sections (just like a traditional mop) to begin cleaning. Start in the corner of your room furthest from the exit and work toward the door. The sloshing of the water in the tank will naturally produce steam while you clean.^{[12]XResearch source}
- Pump the handle again while mopping to produce extra steam for stubborn or stuck-on messes.
- Mop with the grain of the floor if you’re cleaning laminate or hardwood.
- Keep the mop moving at all times. If it’s left to idle in one spot too long, the excess heat and moisture can damage that spot on your floor, especially if it's made of wood.
Quickly swivel the mophead around to use the other side of the pad to keep mopping.^{[13]XResearch source} If you need to replace the pad, unplug the mop and wait 2 or 3 minutes for it to cool down. Then you can safely handle the mophead and put on a new pad.^{[14]XResearch source}
If you run out of water, unplug the mop and wait 2 or 3 minutes for it to cool. Then refill the tank with the included measuring cup, making sure not to overfill it.^{[15]XResearch source}
7
Turn off the mop with the on/standby button when you’re done mopping. First, press and hold the on/standby button until it starts flashing blue to stop steaming. Then unplug the mop and let it stand upright for 2 or 3 minutes while it cools. When it’s cool to the touch, it’s safe to disassemble and store.^{[16]XResearch source}
- Press the power cord release button to wind the cord back inside the mop.
8
Remove the cleaning pad when the mophead is cool. Release the fasteners holding the pad in place and pull on the lavender loop to slide the pad off. Always remove the damp pad before storing the mop to avoid mildew or mold.^{[17]XResearch source}
- Some models have a no-touch release button or switch that ejects the cleaning pad without having to touch it.
- Shark steam mop pads are reusable and machine washable. Shake away loose dirt and snip off loose threads before washing.
First, unscrew the water tank cap and pour out any leftover water into a sink or tub. Replace the cap when you’re done.^{[18]XResearch source} Then remove the mophead by pressing the release button near the bottom of the mop body.^{[19]XResearch source} Hang the mop vertically from a large hook to store it, keeping the mophead separate.^{[20]XResearch source}

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Always use a carpet glider attachment (a plastic frame that attaches to the mophead) to refresh carpeted floors.^{[21]XResearch source}
Thanks
Helpful0 Not Helpful0
Shark steam mops come in a variety of models. To get the most out of your mop, consult the user’s manual for model-specific instructions.
Thanks
Helpful0 Not Helpful0
Use a paper clip or nozzle cleaning tool to remove buildup in the opening of the steam nozzle. Buildup forms when your water is hard or you’ve added other cleaners into the water tank.
Thanks
Helpful0 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

When you’re mopping in the bathroom, keep the mophead a few inches away from toilets and tubs. The cold porcelain might crack with an abrupt temperature change.
Thanks
Helpful2 Not Helpful0
Only handle the plug with dry hands to avoid the risk of electric shock.
Thanks
Helpful0 Not Helpful1
Only use the mop with water. It will overheat and get damaged if you turn it on with an empty water tank.^{[22]XResearch source}
Thanks
Helpful0 Not Helpful0