How to Unwarp Wood

Download Article

Explore this Article

methods

1Using an Iron

2Using Sunlight

3Using Pressure

Other Sections

Questions & Answers

Things You'll Need

Related Articles

References

Article Summary

Download Article

Wood tends to warp when exposed to moisture and heat. Applying additional moisture and heat to the opposite side of the warp can cause the wood to warp back into its original flat position, effectively “unwarping” the piece. Minor warping can usually be corrected with heat and moisture only, but for more severe warping, you may also need to apply pressure to the wood.

Steps

Method 1

Method 1 of 3:

Using an Iron

Download Article

1. 
   1
   Wrap the wood in moistened towels. Moisten one or two large towels and wrap them around the wood, making sure that the entire warped area is covered.

   • The towels you use should ideally be large enough to cover the entire wood piece. Choose towels or rags that can withstand the heat of an iron.
   • When moistening the towels, drench them thoroughly and wring out the excess water. The towels should be damp but not dripping wet.
2. 
   2
   Place the covered wood on an ironing board. Place the wrapped wood on an ironing board or other flat, hard surface. The raised "bubble" should face up.

   • The concave or inward curving surface should face down.
   • The surface you place the wood on must be rigid. It should also be able to withstand the high heat of an iron.
   Advertisement
3. 
   3
   Heat an iron to its highest setting. Turn on a steam iron and switch its temperature setting to the highest point.

   • Give the iron two to five minutes to heat up.
   • Note that the iron should be designed to work with steam. A dry iron is not recommended.
4. 
   4
   Press the iron over the warped surface. Press the iron down on one end of the covered wood. Gradually slide it all the way over the entire surface, applying even pressure to the warped area.

   • Hold the iron on each spot for 5 to 10 seconds before sliding it to the next spot.
   • Each spot should overlap slightly to ensure that the entire wood piece is covered.
   • Do not leave the iron unattended at any point. An unattended iron can burn the press towel and the wood beneath it.
5. 
   5
   Repeat as needed. Check the progress of the wood. If the problem has been corrected, stop here. If some warping remains, repeat the process until the warp is gone.

   • Once the wood has un-warped, turn off the iron and unwrap the wood. Allow the wood to dry thoroughly before use.
   • This process may not work on severely warped pieces. If you do not notice any progress after two or three tries, you may need to try another method.
Advertisement

Method 2

Method 2 of 3:

Using Sunlight

Download Article

1. 
   1
   Wrap the wood in moistened towels. Moisten several large towels and wrap them completely around the warped wood.

   • You can use towels, sheets, or rags. The material you use must retain moisture and be large enough to wrap around the warped wood piece.
   • Run the towels under water until they are soaked, then wring out as much excess moisture as possible. The material should be moist when you wrap it around the wood, but it should not be drenched.
2. 
   2
   Place the wood in bright, direct sunlight. Set the wrapped wood out in a warm area that receives a lot of sunlight during the day. The concave (inwardly bent) side should face down and the convex (outwardly bent) side should face up.

   • You may want to place a plastic tarp beneath the wood to prevent the water from soaking the surrounding area.
   • This method works best during warm, dry weather. It may not work in cold, cloudy, or wet conditions.
   • For best results, place the wood on top of a rigid surface, like a driveway or deck. You can place it on top of your lawn, but the process may not be as effective if the wood sits on a soft surface.
3. 
   3
   Spray with additional water as needed. Depending on the extent of the warping, you will need to keep the wood in sunlight for two to four days. Spray the towels with additional water throughout this period to keep the wood moist.

   • As before, the material should only be moist and not dripping wet.
   • The sunlight should heat the covered wood and encourage it to absorb moisture from the towels. As moisture is absorbed into the surface, the wood should begin to warp back into its proper position.
4. 
   4
   Dry until the warping vanishes. The entire process can take several days depending on the damage. Check it regularly. Once the wood is unwarped, remove the wrappings and let it dry.

   • When the sun disappears at night, you should bring the wood inside. Keep it in a warm place overnight with the inward curve facing down.
   • If you do not notice any progress after a few days, you may need to try a different method.
Advertisement

Method 3

Method 3 of 3:

Using Pressure

Download Article

1. 
   1
   Cover the wood with damp paper towels. Moisten several sheets of paper towel and arrange them over the concave (inwardly curved) surface of the wood.

   • Paper towels are ideal for this method, but a thin steaming towel or standard paper can also be used. The material you use must be moistened, however, and it must be large enough to cover the entire warped area.
   • Rinse the paper towels under water, then carefully wring out the excess. The material should be moist when you drape it around the wood, but it should not be dripping wet.
   • Only apply the wet paper towels to the concave side of the wood for this method. By concentrating the moisture on the side, you can help direct the warping back to its original flat position. The concave side will absorb more moisture while the convex (outwardly bent) side will dry out.
2. 
   2
   Wrap plastic over the paper towels. Wrap several layers of plastic wrap all the way around the wood and the moist paper towels. The plastic wrap must be tight and secure.

   • The plastic should slow down the process of evaporation, keeping the paper towels and wood moist for a longer period of time as a result.
   • Make sure that the plastic wrap covers all sides of the wood, not just the side covered by paper towels.
3. 
   3
   Place the wood in a clamp. Place the wood in a clamp, over-tightening the clamp slightly until the warped area begins to straighten out.

   • Work carefully while tightening the clamp. If you tighten it too much, the wood might split apart instead of straightening out.
4. 
   4
   Leave for one week. Keep the wood clamped and wrapped in a warm location for one week.

   • Check regularly and remove the wood from the clamp if you see signs of possible damage.
   • The storage area should be as warm as possible during this first week. Ideal temperatures would be as high as 149 degrees Fahrenheit (65 degrees Celsius), but if heat that warm is impossible to maintain, the hottest room you have should suffice for most purposes.
   • You can keep the wood warmer if you let it sit in direct sunlight, beneath a heat lamp, beneath an electric blanket, or over a warming mat. Keep the heat on the wood for at least six to eight hours per day.
5. 
   5
   Remove the wrappings. After the first week, remove the wood from the clamp and take off the plastic wrap and paper towels.

   • At this point, the wood must be allowed to thoroughly dry.
   • Check the progress of the warp. If it has vanished, the wood piece is ready to use as soon as it dries and not additional pressure is needed.
6. 
   6
   Apply additional pressure. If some warping still remains, return the wood to its clamped position and let it dry that way for two to three weeks.

   • The temperature can be somewhat cooler for this stage, but the ideal temperature is still 77 degrees Fahrenheit (25 degrees Celsius).
   • The air of the room should also be dry during this stage. Do not store the wood in a humid room.
7. 
   7
   Check the progress frequently. As soon as the wood has completely dried throughout the entire piece, it should be ready to unclamp and use.

   • If the wood has not unwarped after you complete this process, the damage might be too severe to reverse.
Advertisement

Community Q&A

Search

Add New Question

• Question

  I have a slight warp/curve in a tabletop I'm refinishing. My wonderful and brilliant husband said I could wet the tabletop on both sides and clamp it between 2 boards. Is this true?

  

  Community Answer

  Yep, the hubby's right. You may have to do it a bunch of times before the wood fully accepts its straightening, but it works and is done everyday.

  Thanks! We're glad this was helpful.
  Thank you for your feedback.
  If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn

  YesNo

  Not Helpful 8Helpful 16
• Question

  How do you straighten hard wood that is 1/4th of an inch thick?

  

  Community Answer

  I think only steaming/ironing is your only hope for that thinner stuff. Or, install it damp and with finish screws instead of nails and you'll be perfectly fine.

  Thanks! We're glad this was helpful.
  Thank you for your feedback.
  If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn

  YesNo

  Not Helpful 3Helpful 15
• Question

  Do any of these three methods work for GAF composite 2x4 or 1x10 deck lumber?

  

  Community Answer

  I doubt these exact methods would work, due to the amount of plastic in the composite. However, heat would be your best bet. Try wrapping black trash bags around the lumber and setting it in the sun.

  Thanks! We're glad this was helpful.
  Thank you for your feedback.
  If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn

  YesNo

  Not Helpful 3Helpful 12

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Advertisement

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Things You'll Need

Using an Iron

• Damp towels
• Ironing board
• Steam iron

Using Sunlight

• Damp towels
• Spray bottle
• Plastic tarp

Using Pressure

• Paper towels
• Plastic wrap
• Clamp
• Heat lamp