How to Untie a Balloon

There are a few ways of untying your favorite balloons. For those who plan ahead, there are easier ways of preparing your balloon to be untied. Both amateur and professional balloon handlers pop balloons in this process. It'll take time to successfully master the untying process. Be patient and be prepared to pop a balloon or two.

Method 1

Method 1 of 3:

Using a Fork or Needle

Download Article

Look closely at the balloon knot and find where it rolls over itself.
You must be careful in this process. You want to be able to see the area where you'll be able to slide your fork into.
Advertisement
3
Slide one of the fork prongs through the knot. Unless the knot is super tight, it should slide through real easy.
- Careful not to pierce the balloon at this stage.
4
Use a knitting needle. This works even better than a fork prong. Thick needles with a blunt, rounded point are the best. Moisten the needle a little bit by licking it for easier access.
- The edge of a knitting needle is pointed enough to get into that tight little spot.
- But it is not sharp enough to pop the balloon.
- You can use it to loosen the knot and untie it.
Use either the needle or fork to roll the knot out. You can help by trying to push the knot while sliding it down.^{[1]XResearch source}
If it doesn't unroll the first time, slide it back up and repeat this process.

Method 2

Method 2 of 3:

Untying Without Any Tools

Download Article

Hold the balloon so the inflated portion is wedged into your lap. Secure the balloon gently but firmly using your thighs.
Try to follow where the knot loops around itself. Visualize how the knot was formed.
3
Push and pull the knot.^{[2]XResearch source} The ultimate process of loosening the knot is to push and pull various sides of the knot. Continue this until you are able to get part of the knot to yield.^{[3]XResearch source}
- Focus on particular loops of the knot when pushing and pulling. The goal is to loosen and grip a single strand of the knot.
4
Separate a strand with your finger. Lodge your fingernail into one of the loops. Try to get a secured grip of that particular loop. You'll need to work on loosening the knot for a while before you can secure a section of the knot.
- This is easier if your fingernails are long.
Once you grip a strand of the knot, locate its connecting loop. Using your other hand, pry out the folded loop underneath the other loop. By prying one loop of the knot with one hand, you should be able to loosen this part of the knot.^{[4]XResearch source}
Once you've separated two loops of the knot, there should be a small opening. Wedge your fang tooth into the opened crevice. By pulling with your hands, gently, the knot should loosen and untie.

Method 3

Method 3 of 3:

Create a Temporary Knot

Download Article

Be sure it is full but not overly full. Inflate it 3/4 of the way full.
2
Use a rubber band. Twist the neck several times so it is well sealed. Stretch out the balloon with one hand. Wrap a rubber band around the neck, and tuck it into the other end of the rubber band. Pull the longer end tight.^{[5]XResearch source}
- This knot is called a lark's head knot. The goal is to use the rubber band as a tightening agent.
- For increased support, you could tie the rubber band as well. This could be just as challenging to untie as a regular balloon's knot.
One of the easier ways of deflating your balloon without popping it is to use a twist tie. Simply hold the neck tight with one hand, and then begin securing the neck with a twist tie.
Do the same process as above, only this time secure the balloon with a clothespin. Be sure the clothespin is fresh and sturdy, or else it might not hold the air well.
5
Tape the balloon's end. Have a few strips of tape ready to be used. Grip the neck of the inflated balloon with one hand. Then tape off the ends using your strips.
- Use scotch tape for the best results.

Community Q&A

Search

Add New Question

Question
Why, when I put the fork prong through, is it covered in latex?
Community Answer
This is because you are pushing against the latex! You have to push through the different sections of latex, not through one. That would result in a hole in your balloon!
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 16 Helpful 18
Question
How do I untie a balloon at school?
Community Answer
Hold just above the knot airtight so no loud noise is made when you finish. Push one end of the rubbery material through the loop, and pull out on the other side. Now you should be holding a an untied balloon. Slowly let the air out, careful not to make any noise, and hold it tightly so that it doesn't escape and fly around the room.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 11 Helpful 23
Question
Can I use a lock pick? If so, how?
Community Answer
It depends on the thickness. It must be thin enough to fit through the knot. But if you are using wire or a bendy object, I say you should use something else. If the item that you are using is bendy, it may be hard to slip it through. If you have big fingers, use something thick enough to get a grip on with your hands. Make sure that your lock pick is mostly a straight line, as it may be hard to handle a wavy or spiky one.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 8 Helpful 12