How to Test a Multimeter

A multimeter is a device that measures several different kinds of electric power, making it a handy tool for all households to have. However, like all devices, a multimeter could gradually fail over time, and there are 2 main ways to test what’s causing the problems. Measure the meter’s fuses to see if any are blown and need replacement. Then, check how accurately the meter measures voltage to see if the whole device needs replacement. While digital and analog multimeters have some differences, these 2 tests can help you determine if the device is working properly.

Method 1

Method 1 of 2:

Measuring the Fuse Performance

Download Article

1
Set the multimeter to the ohms setting. Turn the large knob on your multimeter to the ohms position, which might also be represented by the Ω symbol. This setting measures electrical resistance and shows you if any fuses are faulty.^{[1]XResearch source}
- With this method you can test the fuses without removing them, but you could also test the fuses manually. Open the back housing of the multimeter and pop the fuses out. Set the multimeter to ohms, then press the red probe to one end of the fuse and the black probe against the other. If the multimeter produces a reading, then the fuse is good. If it doesn't, then the fuse is blown.
2
Plug the red lead into voltage-ohm jack. Find the voltage-ohm input on the front of the multimeter, which is usually on the right side. It might be represented with a VΩ symbol. Take the input side of the red lead and plug it into this jack.^{[2]XResearch source}
- Many multimeters color-code their input jacks, so the voltage-ohm input will be red on a model like this.
- For this test, you don’t need the black lead.
Advertisement
3
Touch the red probe to the amp jack. This jack is on the left-front of the multimeter and may be marked with an A symbol. Insert the red probe into the jack. Hold it in place for a few seconds and wait for a continuity reading. If the multimeter gives you a reading, then the fuse is good. If not, the fuse is blown.^{[3]XResearch source}
- If your multimeter has an audio setting, turn it up. A beep indicates continuity and tells you that a fuse is functioning.
The milliamp jack is right next to the amp jack, and might have a mA symbol next to it. Insert the probe the same way as you did on the amp jack and wait for a reading. If the multimeter doesn't produce a reading, then this fuse is blown.^{[4]XResearch source}
5
Replace any fuse that doesn’t show continuity when you measure it. If the multimeter doesn’t produce a reading for one or both fuses, then you can get new ones made for that multimeter type. Go to the hardware store and get a pack of fuses that match your multimeter type. Unscrew the back of the meter and lift the cover off the housing to reveal the 2 fuses. Pull the defective fuse out and pop the new one in. Close up the meter and run the same test to confirm that the new fuse is working.^{[5]XResearch source}
- The best way to pick a new replacement fuse is pull the fuses out of the multimeter and get ones that match this type. The user manual should also note what type of fuse the device uses. If you still aren't sure, contact the manufacturer and ask.
- You can also buy bulk packs of fuses online. If you're an electrician or have a lot of tools that use the same fuse, then this may be the most cost-effective choice.
- The multimeter will still work in its other functions if fuses are blown. If a fuse is blown, it only means you can’t measure current, or amps.

Method 2

Method 2 of 2:

Checking the Meter’s Accuracy

Download Article

1
Get a new alkaline battery. It doesn’t matter what type of battery you use, as long as it’s new so you know it’s fresh. AA, AAA, C, D, or 9V will all work. They have known voltages so they provide a good baseline to test the meter.^{[6]XResearch source}
- AA, AAA, C, and D batteries all have 1.5 volts and a 9V has 9 volts.
- A multimeter can also measure rechargeable or lithium batteries, but the voltages on these batteries can vary. They don’t provide as good of a baseline.
2
Plug the black lead into the common jack and the red one into the volt-ohm jack. These inputs are on the right-front of the multimeter. The common jack might say COM and the Volts jack is marked with a VΩ symbol. Plug the input side of each plug into the correct jack.^{[7]XResearch source}
- On many multimeters, these 2 jacks are color-coded. In this case, just match the black wire with the black port and vice-versa.
3
Set the multimeter to Volts DC. Turn the knob on the front of the multimeter to the position that reads Volts DC, DCV, or V-. These settings all measure direct current, which batteries produce.^{[8]XResearch source}
- Some multimeters might use different symbols for their knobs. Check the manual that came with your meter if you don’t see any of these symbols.
4
Hold the red probe to the battery’s positive side and black probe to the negative. Hold the probes in place for a few seconds and wait for the meter to produce a reading. For AA, AAA, C, and D batteries, the reading should be 1.5 volts and a 9V should read 9 volts, or within 0.02 points of those readings. If the readings are accurate, then the meter is in good working order.^{[9]XResearch source}
- If the readings are off, try testing a few different new batteries just to make sure the battery you tested wasn’t defective.
5
Replace your multimeter if it doesn’t read the battery voltage correctly. If you’ve tried testing several batteries and the readings are off, then your meter might be defective. Try contacting the meter manufacturer to see if you can get a replacement, or buy a new one from a hardware store.^{[10]XResearch source}
- You might be able to fix the meter. Try showing it to a hardware store employee and see if they can adjust it for you. Otherwise, you’ll need a new one.
- An analog multimeter is easier to fix because the dial may just need calibration. A digital one might need total replacement.

Expert Q&A

Search

Add New Question

Question
How do I know whether to use AC or DC settings?
Jesse Kuhlman
Master Electrician, Kuhlman Electric
Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.
Jesse Kuhlman
Master Electrician, Kuhlman Electric
Expert Answer
You have to know what you're working with ahead of time. The vast majority of appliances and outlets in a home are going to be AC. It totally depends on what you're testing, though.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 0
Question
What's the difference between amperage and voltage?
Jesse Kuhlman
Master Electrician, Kuhlman Electric
Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.
Jesse Kuhlman
Master Electrician, Kuhlman Electric
Expert Answer
The easiest way to think about it is like the water in a hose. Voltage is the water pressure, and amperage is the size of the hose. The larger the hose, the more water it can hold, right? That's the difference between amperage, which is current, and voltage.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0
Question
What's the number on the multimeter screen?
Jesse Kuhlman
Master Electrician, Kuhlman Electric
Jesse Kuhlman is a Master Electrician and the Owner of Kuhlman Electric based in Massachusetts. Jesse specializes in all aspects of home and residential wiring, troubleshooting, generator installation, and WiFi thermostats. Jesse is also the author of four eBooks on home wiring including "Residential Electrical Troubleshooting" which covers basic electrical troubleshooting in residential homes.
Jesse Kuhlman
Master Electrician, Kuhlman Electric
Expert Answer
It's going to depend on the setting your multimeter is set to. So, if your multimeter is set to read the current, the number on the screen is going to be the amperage. If it's set to voltage, it's going to show the voltage.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0