How to Tell if Water Heater Is 120 or 240

Not sure what type of water heater you have at home? That’s totally fair—while a lot of electric water heaters are 240-volt, some are only 120-volt. We’re here to help you figure out exactly what kind of electric water heater you have, as well as how to safely test your heater’s voltage if you want to be extra certain With the proper safety precautions, you can be more in the know about this important at-home appliance.

Section 1 of 4:

How can I figure out the voltage of my water heater?

Download Article

Check the label attached to the outside of your water heater. All water heater tanks have a sticker on the side that includes all the important info about the appliance, including the serial number, model number, and voltage. Check the number next to the “Volts” category—it’ll say either 120 or 240.^{[1]XResearch source}
- Some water heaters may also by 208 Volts, but 240 is the most common voltage for a home water heater.

Section 2 of 4:

What’s the difference between a 120- and 240-volt heater?

Download Article

A 240-volt heater can be more efficient than a 120-volt heater. In the world of electricity, voltage relates to the total potential of an electricity source to accomplish a specific task—in this case, heating your water!^{[2]XResearch source} So, it’s not surprising that 240-volt water heaters are really common in most homes since they don’t create as much of an amp draw.^{[3]XResearch source}
- Heaters are powered with either a 1-pole or 2-pole circuit breaker. A 120-volt heater always uses a 1-pole circuit breaker, while a 240-volt heater always uses a 2-pole circuit breaker.
  - Note that hits only apply to residential settings. In a commercial setting, you can actually have a 208-volt or 277-volt circuit, for instance.
- Larger water heaters tend to be 240-volt. In fact, most homes nowadays are built with 240-volt heaters.^{[4]XResearch source} Don’t assume that this is the case for your home, though—it’s always better to check and be safe.

Section 3 of 4:

Can a 240-volt water heater run on 120 volts?

Download Article

Yes, but experts don’t recommend wiring your water heater this way. A 120-volt circuit breaker can’t operate with the full power of a 240-volt circuit breaker. At best, you’ll get about 25% of the water heater’s total power, which isn’t very efficient (or warm!) at all. Instead, it’s always best to operate your water heater at the correct voltage level.^{[5]XResearch source}
- On the flip side, it’s never a good idea to install a 120-volt water heater to a 240-volt circuit. The circuit will be too powerful for the heater and completely break it. Operating a 120-volt water heater on a 240-volt circuit may also start a fire in your home.

Section 4 of 4:

How to Test Your Water Heater Voltage

Download Article

Head to your circuit breaker and switch off the power that’s connected to your water heater. The circuit switch is usually labeled as either “hot water heater” or “HWT.”^{[6]XResearch source}
2
Double-check that the power is off with a non-contact voltage tester. Look for a clump of wires along the very top of your water heater tank. Then, switch on the voltage tester and press it against the wire for a few seconds. If it beeps, your water heater is still powered up; if it’s silent, the water heater is totally powered down and safe to test.^{[7]XResearch source}
- Tap your voltage tester against a plugged-in cord first to make sure that it’s working correctly.
- If the device beeps, go back to your circuit breaker and make sure that the right switch is turned off.
3
Remove the access panel and remove the insulation. Electric water heaters house all their wires in an insulated access panel, which is covered with a rectangular metal plate. Remove the access panel with a screwdriver, and then pull out the insulation that’s covering the wires and terminal screws.^{[8]XResearch source}
- Some water heaters may not let you pull out the insulation completely. In this case, tape it to the side of the heater tank so you can clearly see all the wires and terminals.^{[9]XResearch source}
- Certain water heaters may also have plastic casing on top of the wires and terminals. Be sure to pull this cover off before you start testing.^{[10]XResearch source}
To test the voltage of your water heater, you’ll need a constant flow of power running through your device. Head back to your circuit breaker and switch the water heater’s power back on.^{[11]XResearch source}
Look for 2 circular ports along the bottom of your multimeter—a red opening marked “V” (for voltage) and a black port marked “COM” (for common). Then, plug the red probe cord into the red “V” port and the black probe cord into the black “COM” port.^{[12]XResearch source}
6
Adjust your multimeter to a voltage setting that’s higher than 240 volts. Look for the voltage section of measurements on your multimeter—they’ll be marked with a “V” followed by a squiggly line. Then, turn or adjust your multimeter to a high voltage setting, like 600.^{[13]XResearch source}
- Double-check the bottom of your multimeter to see how many volts it can handle. You don’t want to accidentally damage your multimeter by overloading it!
- If your multimeter is set to less than 240 volts, it won’t be able to properly register the voltage of your water heater.
7
Test your water heater’s voltage with the multimeter. Use the multimeter by pressing the red probe to the topmost screw on one side and the black probe to the topmost screw on the other side. It doesn’t matter which probe is on which screw, as long as they’re each touching a different terminal.^{[14]XResearch source}
- Make sure that you aren’t touching or handling the metal ends of the probes, or else you might get shocked.
- For extra protection, slide on a pair of rubber insulating gloves that are cleared for at least 240 volts of shock. This way, you’ll be protected even if you touch a live terminal or wire.^{[15]XResearch source}
8
Read the multimeter screen to determine your heater’s voltage. In a moment, you’ll see either “120” or “240” popping up on your screen, confirming the exact voltage of your water heater.
- If no voltage number shows up on your device, you may need to get it repaired.

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Only check your water heater’s voltage if you feel comfortable working with your home’s electricity system. Feel free to call a professional if necessary!
Thanks
Helpful1 Not Helpful0