How to Replace Pool Tiles

If your swimming pool is over 15 years old or has taken quite a bit of wear and tear, you may need to replace some of the tiles. Start by lowering your water level and removing any cracked or damaged tiles. Find some replacement tiles and install them with thinset mortar, then seal them in place with grout. Once you’re done and everything’s dry, bring the pool’s level back up and reward yourself with a swim!

Part 1

Part 1 of 3:

Removing Cracked or Damaged Tiles

Download Article

1
Drain your pool below the tiles that need replacing and let the area dry. Use a submersible pump to drain out enough water to leave the damaged area exposed and dry. Once the area is clear, turn off the pump and let the tile dry off completely. It’s best to do this in bright sunlight, which will dry the tile quickly.
- If you’re only replacing a couple tiles along a top edge, you’ll only need to drain enough water to expose the area and keep it from being splashed.
- If you’re redoing your entire pool, drain all of the water and let it sit for a day or 2, until it’s fully dry.
- There are also special adhesives available for re-attaching single tiles underwater. However, your repair will be much more effective and durable if you drain your pool first.^{[1]XResearch source}
This tool essentially looks like a screwdriver with a saw blade on the end of it. Push the blade end against the grout and saw it back and forth to cut through the grout. Keep cutting through until you remove all of the grout around the tiles that need to be replaced.^{[2]XResearch source}
Advertisement
3
Use a hammer and chisel to remove any damaged tiles. Place the tip of the chisel in the joint of the cracked tile, then tap it with the head of the hammer to break the tile away from the mortar. Keep tapping until the whole tile comes away, then repeat on any other damaged tiles.^{[3]XResearch source}
- If your tiles are small, you can use a small flathead screwdriver instead of a chisel.
4
Inspect the beam behind the tile for any necessary repairs. Look for cracks, open seams, an uneven surface, or missing chunks in the beam. If the damage is greater than some damaged tiles, you’ll need to shore up the base with hydraulic cement or a plaster mix. This is essential for ensuring the longevity of your pool as well as creating a flat surface for the tile to stick to.
- If the damage looks like it could be extensive, contact a professional full-service pool company to help diagnose and repair the problem.

Part 2

Part 2 of 3:

Finding Replacement Tiles

Download Article

If the tiles came off but they’re still in 1 piece, you can simply re-attach them! This will save you a lot of time, instead of trying to find new tiles that fit the pattern or space available. When the tiles fall off, keep them together in a safe spot where they won’t get bumped, cracked, or lost.^{[4]XResearch source}
2
Ask your original pool builder for tile, if possible. If you know who built your pool and they’re still available, they may still have extra tiles handy. Send them an email, including a picture of the tile and a quick description, and ask if they have access to any extra tiles.^{[5]XResearch source}
- You’ll also need to ask for a price, which may be discounted due to your past business.
3
Check online or at local pool stores for similar or identical tiles. Pool stores are good for comparing colors up close, but online pool tile catalogues will likely give you the most variety to choose from. Settle for a close match if the repair is in a less obvious area, such as somewhere you can’t see from the house.^{[6]XResearch source}
- As long as the color is the same and the shape and size are similar, they probably won’t stand out too much!
4
Have tiles custom-made to match your original tiles exactly. This option is more expensive, but if you can’t find a match for your tiles, this will give you the most seamless repair. Consult with a custom tile company to see if they can recreate your tile. Bring photographs of the original tile to give them a reference.
- To find a custom tile company, look online or locally and set up a consultation.

Part 3

Part 3 of 3:

Installing New Pool Tiles

Download Article

1
Mix up a batch of swimming pool thinset repair mortar. Follow the instructions on the packaging to measure and mix the mortar and water. Use a trowel to stir the mixture in a plastic container or metal bowl. Keep adjusting the proportions as needed until the mixture reaches a spreadable, peanut butter-like consistency. Stir well to get rid of any lumps.
- The thick, spreadable consistency will help keep the mortar from dripping into the pool water.
- Some thinset mortars also come with a bonding agent, which increases the adhesive quality. Mix equal parts mortar and bonding agent, then add water until the mixture thickens to a creamy, spreadable texture.^{[7]XResearch source}
2
Spread a ¹⁄₈ inch (0.32 cm) layer of thinset on the back of the new tile. With your trowel, scoop up a daub of thinset and smooth it out over the entire back of the tile, all the way up to the edges. Line the tile up on the pool wall so it matches any existing pattern, then press it firmly against the beam.^{[8]XResearch source}
- Thinset dries quickly, so make sure to place the tile immediately after covering the back.
3
Keep the tiles in place while they dry for 24-48 hours. Check on the tiles’ progress every 10 minutes for 1-2 hours to see if they’ve slipped down the pool wall. If any small tiles slip, simply slide them back up and press them into place. For larger tiles, you should duct tape them into place while they dry.
- 24 hours should be enough to dry the thinset mortar, but waiting up to 48 hours will let it cure and harden even more.
4
Use waterproof tile grout to fill in the spaces between the tiles. Load up a flexible spreader with grout and push the product between the tiles. Once you’ve filled up the space, let the grout set for 10-15 minutes, then use wet your hands and gently rub at any excess grout smeared on the tiles.
- To avoid dropping any daubs of grout into the pool, work with small amounts at a time.
- If the dried-on grout is stubborn, wait 24 hours and scrub the tiles with a stiff brush to polish and remove any haze.
- After letting the grout dry for 24 hours, you can refill the pool and enjoy the product of your hard work!

Community Q&A

Search

Add New Question

Question
Our pool tiles started to fall and the concrete surface behind is uneven. what product should we use to fill the uneven surface before we put the new tile? Can we use thinset mortar? is it waterproof?
Lina DaSilva
Top Answerer
Thinset mortar is often a good choice for this purpose. While thinset mortar itself is not waterproof, it is moisture-resistant, which makes it suitable for use in pool areas. However, for complete waterproofing, you should use a waterproof membrane or a waterproofing agent in conjunction with thinset mortar.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 0
Question
How do you remove old adhesive that is still attached?
Lina DaSilva
Top Answerer
Warm water can soften some types of adhesive. Soak a cloth in warm water and lay it over the adhesive for a few minutes. This can make scraping easier. Use a plastic scraper (to avoid scratching the tiles) to gently remove the adhesive. If it’s stubborn, a putty knife can also work, but be gentle. If water and scraping aren’t cutting it, a chemical adhesive remover might work. Apply it as directed on the product, usually letting it sit for a bit, and then scrape off the adhesive.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 0
Question
Where can I buy thinset mortar?
Lina DaSilva
Top Answerer
You can find thinset mortar at most hardware stores or home improvement centers. Check out places like Home Depot, Lowe's, or your local hardware store. They usually have a variety of options for different types of tiling projects. You can also find it online on websites like Amazon, but remember to check the specifications to ensure it's the right type for your project.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 1

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Things You’ll Need

Removing Cracked or Damaged Tiles

Grout saw
Hammer
Chisel
Hydraulic cement or plaster mix (if the beam needs repairing)

Installing New Pool Tiles

Thinset mortar
Trowel
Tiles
Duct tape
Waterproof grout
Stiff brush or scrubber

Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Cracked pool tiles can sometimes indicate beam damage. Make sure to check behind the tile before replacing it.
Thanks
Helpful0 Not Helpful0
When your swimming pool tiles are cracked and damaged, they can be a safety hazard to swimmers, so be sure to replace them quickly.^{[9]XResearch source}
Thanks
Helpful0 Not Helpful0