How to Replace Fluorescent Lighting

Changing a standard incandescent light bulb is, of course, the simplest of tasks. However, you may find yourself pausing when it comes time to replace a long, tube-style fluorescent lamp that is not immediately obvious how the bulb is removed from the housing. While it may seem intimidating, replacing fluorescent lighting can be simple.

Method 1

Method 1 of 3:

Replacing the Bulb

Download Article

Before replacing a fluorescent light, you should make sure the fixture is not powered on. Do not simply use the wall switch to remove power to the fixture. You can use the fuse box to shut off power to the lamp's circuit. Use a voltage tester to verify that there is no power in the fixture.^{[1]XExpert SourceDaniel Stoescu
Master ElectricianExpert Interview. 21 June 2021.}
Most likely, you will not be able to reach the fluorescent light fixture comfortably from ground level. Position a stepladder underneath the fixture to replace the lamps comfortably and safely.^{[2]XExpert SourceDaniel Stoescu
Master ElectricianExpert Interview. 21 June 2021.}
Advertisement
Reach up, and gently support the first fluorescent tube with both hands, keeping your hands as close to the ends of the bulb as possible. You will be able to rotate the tube in either direction a quarter-turn until it stops. This action rotates the prongs, that project from each end of the bulb, to a vertical alignment, and so allows you to slide the tube downward and out of the fixture.
Place the tube gently out of the way, where it cannot roll or be disturbed.
5
Lift the new fluorescent tube into place. To install the new light, line its prongs up with the slots in either socket. Push the tube straight up into the sockets, and then rotate it 90 degrees until you feel it lock into place. You can give the lamp a gentle tug to ensure that it is firmly in place.^{[3]XExpert SourceDaniel Stoescu
Master ElectricianExpert Interview. 21 June 2021.}
- Consider installing LED lighting instead, which uses less energy, lasts longer, and produces a more natural light.
Most often, fluorescent light fixtures are designed with two tubes side-by-side. The process for replacing each tube is the same.^{[4]XResearch source}
Flip the fuse box switch back on, then flip your wall switch on. See if the new fluorescent bulbs light up properly, noting that fluorescent lamps take a minute or so to reach full brightness. If the new bulbs do not work properly, you may have a defective component in your light fixture that needs to be replaced.^{[5]XExpert SourceDaniel Stoescu
Master ElectricianExpert Interview. 21 June 2021.}

Method 2

Method 2 of 3:

Troubleshooting Problems

Download Article

Cracked sockets are often caused by other objects bumping into the fixture, or too much stress while removing a bulb. First, turn off the power to the light, and remove the bulbs. Keep the wiring order straight as you take out the old socket. It is important to cut only one wire lose at a time. Strip each wire back by 1/2 in., and put the stripped wire end into the terminal slots of the new socket. Do this for each wire.^{[6]XResearch source}
2
Inspect the ballast. The ballast controls the amount of incoming voltage that start the light tubes. It also regulates the electricity to give constant light. If you believe that the ballast needs replacement, you may want to consider purchasing a whole new fixture. Ballast replacement may cost the same amount as a new fixture.^{[7]XResearch source}
- A humming sound produced by your fluorescent light fixture usually indicates that the ballast, rather than the bulbs, needs to be replaced.
3
Check the fuse box for flickering lights. The bulb may not be getting enough power. Try resetting the fuse box by flipping the power switch off and on.^{[8]XResearch source}
- If the bulb is still flickering, try replacing the bulb.^{[9]XResearch source}

Method 3

Method 3 of 3:

Working with Office or Recessed Lighting

Download Article

Office lighting is usually behind a bezel lens with a frame. These types of recessed fixtures are holding the light tubes in place to minimize accidents and breakage. They can be very frustrating due to the lack of wiggle room or freedom of movement. The frame is held in place by lever locks or snaps that you have to take out.
First, use a screwdriver to pry down the levers, while supporting the frame in the middle. It is important to support the frame because it can ruin the locks or swing down and hit you in the head.^{[10]XResearch source}
Take the opportunity, while the lens is down, to remove insects, dust, condensation or mold from the lens surface.
4
Take out the bulb. Depending on the bulb, you will either need to twist, or unsnap, each end of the fluorescent tube. Be sure to only do one end at a time to maintain more control over the bulb.^{[11]XExpert SourceDaniel Stoescu
Master ElectricianExpert Interview. 21 June 2021.} Once you wiggle the first tube out, the other tubes will come out much more easily.^{[12]XResearch source}
- Search for holes, or a recessed area, that the cathode/anode pin can sink into that permit freedom of movement.
To install the new light, line its prongs up with the slots in either socket. Push the tube straight up into the sockets, and then rotate it 90 degrees until you feel it lock into place. You can give the lamp a gentle tug to ensure that it is firmly in place.^{[13]XResearch source}
6
Finish the job. When the last tube is in, swing the lens frame back in. Use both hands to support the frame in place. Then, use your thumbs to swing the frame lock back in.
- Snap locks may need to be pressed firmly to snap back in.^{[14]XResearch source}

Video

Expert Q&A

Search

Add New Question

Question
How do you remove a fluorescent light?
Daniel Stoescu
Master Electrician
Daniel Stoescu is a Master Electrician and the Owner and Operator of Home Tech Solutions, LLC in Hampton, Virginia. With over a decade of experience, Daniel specializes in wiring residential, commercial, and light industrial structures. The Home Tech Solutions team has over four decades of combined experience and offers comprehensive solutions for residential electrical needs.
Daniel Stoescu
Master Electrician
Expert Answer
Turn the power off and apply downward pressure at the end of the bulb. Keep in mind that circular fluorescent bulbs may shatter easily.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 3
Question
What is a fluorescent starter?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
A fluorescent starter is a timed switch. It lets the current flow through the filaments, which are located at each end of the fluorescent light tube.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 5
Question
How do you change a light ballast?
How.com.vn Staff Editor
Staff Answer
This answer was written by one of our trained team of researchers who validated it for accuracy and comprehensiveness.
How.com.vn Staff Editor
Staff Answer
Changing a light ballast is an involved process, so it’s important to follow step-by-step instructions that explains exactly what to do. Be sure the replacement used is of the same technology. It is suggested that you read all of this wikihow: How to Replace the Ballast in a Fluorescent Lighting Fixture, including its warnings, so you know what to do correctly.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 2

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Unlike incandescent bulbs, fluorescent bulbs rarely burn out completely. Instead, they dim or begin flickering over time, indicating that they need to be replaced.
Thanks
Helpful4 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Broken light bulbs pose a risk of eye and skin injury. Wearing safety glasses when replacing a bulb will help reduce the risk of eye injury in case of a breakage.
Thanks
Helpful12 Not Helpful6
Fluorescent bulbs of all types contain a small amount of mercury, which means they pose a health risk if broken. If you break a fluorescent bulb, open a window for ventilation and sweep the broken pieces into a container you can reseal for disposal.
Thanks
Helpful11 Not Helpful10