How to Repair Oxidized Cloudy Headlights with a Headlight Cleaner

Over time, the headlights on your car may become cloudy due to oxidation.^{[1]XResearch source} This can cause your headlights to become dim, which can be dangerous. Luckily, it’s easy to restore your headlights yourself with a headlight cleaner!

Method 1

Method 1 of 3:

Using a Glass Cleaning Solution

Download Article

Determine whether the damage to the lens is on the outside or on the inside (if inside you may notice moisture,^{[2]XResearch source} and you may need to remove the lens, if possible and/or drain and dry it). Before trying any of these steps, try a "Headlight Deoxidizer" which will save time and is non-abrasive. Some of these steps may be unnecessary depending upon the damage or oxidation of your headlight lenses.^{[3]XTrustworthy SourceConsumer ReportsNonprofit organization dedicated to consumer advocacy and product testingGo to source} Some headlights will require more work and some may be so bad that replacement is a better option.
You can also use a watered-down degreaser to clean the headlight lenses.
Advertisement
Use a microfiber pad to polish the headlights.
Be sure not to get it on black, rubberized plastic parts as it will make a white film that is hard to remove.
To make this repair last longer seal with car wax or silicone sealer.

Method 2

Method 2 of 3:

Using Masking Tape

Download Article

Easy-to-use kits like the lens repair kit from 3M are available at local automotive retailers. Tape, sandpaper, lens polish and directions are included, and there's an online video that shows you how to do it.
Protect your car's finish with masking or painting tape. Don't use duct tape as it can ruin or lift the paint off your car.^{[4]XResearch source}
3
Clean the headlight lens.
- You can use sandpaper, but remember sandpaper scratches. If your lens has heavy/severe discoloration with apparent scratches/imperfections, this requires a rougher grit sandpaper, like the 600 grit. If the headlight lens has light discoloration with no apparent scratches, start with at 2500 grit. Whichever grit you use, you want to wet the sandpaper in a bucket or cup of soapy water.^{[5]XResearch source}
- Wet the rag with a commercial plastic lens cleaner or degreaser. Make sure you wet the rag instead of spraying the headlight; this keeps the spray from getting on the paint. Wash the lens with a clean rag or a shop towel.
4
- Dip one finger into a plastic polish or a compound designed for plastic. With the lens still wet, apply the polish evenly over the entire headlight.
- Grab a sanding sponge or a soft hand pad and take out the starting sandpaper which you decided earlier, in most cases, the 600 grit sandpaper.
- Fold the sandpaper in three around the Soft Hand Pad Or Sanding Sponge.
- Dip the sponge and sandpaper into the soapy water.
- Sand, using a side to side motion, applying even pressure, periodically wetting the sponge and the sandpaper in the soapy water. (Avoid contacting paint and other surrounding surfaces.)
5
.
- Continue the sanding process using a 1200 grit paper, then even finer 2000 grit and finally 2500 grit sandpaper to remove scratches left by the previous grit.
- Apply the plastic polish/ compound after sanding with the 2500-grit sandpaper. This time, let it haze, then buff/wipe off with a shop towel.
- Clean the lens with a plastic lens cleaner or soap and water. This is to remove any polish residue.
6
Apply wax (protectant) to the headlight lens when the lens is clear. If you are not satisfied with the clarity of the lens, repeat Steps 1 – 5 until the lens is clear.^{[6]XResearch source}
- Seal the lens with wax or silicone sealer.
- Fold a shop towel into four and squeeze a quarter-sized amount of wax or polish onto it and let it soak in for a few seconds.
- Apply to the lens using a single stroke going from left to right gradually working your way down the entire lens.
Remove the masking tape. The headlight repair is complete and you should now have clean headlights that look as good as new and restored optical clarity for safe night driving.

Method 3

Method 3 of 3:

Using Toothpaste

Download Article

Almost any kind — especially whitening ones — have an abrasive such as silica, other fine grit or soda.^{[7]XResearch source}
3
Avoid getting any of the cleaner or polish on paint, chrome, plastic or rubber.
- Be careful and consider masking tape and plastic sheet over the other surfaces to be protected.
Rub on dabs (not great gobs) of toothpaste with a dampened soft cloth or towel to the cool lens, rubbing in a circular motion in part of the headlight that needs it. Remember to work on the edges if dulled or scratched.
Use enough paste and enough pressure to rub out the scratches; so, don’t rub too lightly. As you work you will notice the plastic getting clearer.
For each headlight you need to spend about 3, 4 or 5 minutes.
Notice if it seems about as clear as it will get; stop rubbing, wash off and rinse with clean water and dry with a paper towel, or cloth.

Community Q&A

Search

Add New Question

Question
Can I use bug/tar remover on headlights?
Blues.Guitar.Lessons. .Jim.Bruce
Community Answer
It's best not to use tar remover, as these products are designed for the much more durable car body finishes. Most headlights are made of polycarbonate plastic, which tends to oxidize and go cloudy. Toothpaste cleans away tiny objects and insects stuck onto the surface while gently polishing the plastic.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 6 Helpful 17
Question
I used Wipe New and my one headlight seems streaky. Can I redo the process?
Community Answer
Yes. After doing my first headlight I had a better grasp of what I was doing and the second came out great, so I went back and redid the first one.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 4 Helpful 11
Question
How do I clean moisture on the inside of the lens cover?
Jared Goss
Community Answer
If you have moisture on the inside of your lens, the whole light assembly will need to be replaced. That means that the seal around the lens to the housing is not good any more. There is no good way to reseal it.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 12 Helpful 17

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Headlight restoration should be done in shade rather than under direct sunlight.
Thanks
Helpful8 Not Helpful7
If the processes still do not remove discolored or cloudy lens then a headlight replacement is necessary.
Thanks
Helpful11 Not Helpful13
Lift the hood of the car so you can have full access to the top of the headlight lens for cleaning / restoring.
Thanks
Helpful8 Not Helpful11