Download ArticleDownload ArticleHow.com.vn is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, volunteer authors worked to edit and improve it over time.
How.com.vn marks an article as reader-approved once it receives enough positive feedback. In this case, 93% of readers who voted found the article helpful, earning it our reader-approved status.
This article has been viewed 121,848 times.
Learn more...
A radiator circulates water to provide heat in a room. It is usually installed with clips or brackets on the wall, so you must remove it entirely if you want to repaint the room. You will need to shut off the radiator and bleed out the water before you try to remove it. Then, it can be removed fairly quickly until you are ready to reinstall.
Things You Should Know
- First, turn off the radiator by twisting the valves on either side and removing the cap from each valve.
- Set up a towel below the end of the radiator and unscrew the cap nut with an adjustable wrench, draining water into a wide bowl.
- Get a friend to help you pick up the radiator and tip it towards the bowl, letting the rest of the water drain before storing the radiator.
Steps
Turn the valves off on either side of the radiator. The valves are usually located just above the base points that extend from the ground. Use a clockwise or tightening motion to turn them off.
Remove the caps from the top of these valves. They are plastic or resin and they cover the hot metal valves. Use an adjustable wrench to tighten the valves even further.- Use the wrench to tighten the nuts at the top of the valve.
Advertisement
See if you have thermostatic radiator valves that take the temperature of the room and turn on and off automatically. If you do, you will need to remove them and replace them with a regular cap to turn them off.- Use the caps that came with your radiator or use caps from a nearby radiator if they will only be used for a short time.
- Screw the caps on tight by hand and then with an adjustable wrench.[1]
Place a towel below the end of the radiator, where the valve meets the radiator itself. Along with proper precaution, it will prevent damage to your room.[2]
Put a wide bowl on top of the towel and below the area where the radiator is attached to the valve.[3]
Keep a bucket nearby where you can drain the water in the bowl when it fills up.
Use an adjustable wrench to unscrew the cap nut at the point where the radiator connects to the valve. Turn it counterclockwise until it starts to drip water. Keep turning until the flow is slightly larger.
Let the radiator bleed water in to the bowl. Unscrew it a little more when the flow stops. When you have no more water coming out, you can unscrew the cap nuts completely so that the radiator is no longer connected to the base.
Ask a friend to help you with this part of the process. Radiators are heavy. You will also need to tip it to pour remaining water out.
Set a towel on the ground. Place the bucket on top of it.
Make sure the radiator is free of the nuts and base assembly on either side.[4]
Grab either side of the radiator. Lift up and out to remove the radiator from the brackets.
Tip the end of the radiator that you just used to bleed the radiator toward the bucket. Let the rest of the water flow out of it.[5]
Take the radiator to a safe place for storage until you are done decorating.
Wipe the base valves and cap nuts. They often drip a little water after the radiator is removed.[6]
Community Q&A
- QuestionCan I run the central heating with a radiator removed from the system?
Community AnswerYes, but only if a connecting pipe is installed in place of the radiator in order for the system to work correctly.
Tips
- Once your decorating is finished, you simply have to reverse the process. First, ensure it is on the brackets before you reconnect the cap nuts and open the valves.Thanks
Things You'll Need
- Adjustable wrench/spanner
- Valve caps
- Bowl
- Bucket
- Towels
References
- ↑ https://www.youtube.com/watch?v=eopRvzv2ZYE
- ↑ https://www.youtube.com/watch?v=0IP54Kbgnv0
- ↑ https://www.bobvila.com/articles/how-to-bleed-a-radiator/
- ↑ https://www.youtube.com/watch?v=5dP2S-Mbh0E
- ↑ https://www.diydoctor.org.uk/projects/removing_a_radiator.htm
- ↑ https://www.youtube.com/watch?v=9MYF34BMGhY
About This Article
Removing a radiator is a relatively simple process, but you’ll need someone to help you lift it. You'll need to turn your radiator off at the valves and place a towel under it to catch the water. Then, bleed your radiator like normal using an adjustable wrench. Once you've bled the radiator, get a friend to help you lift it up and out from its brackets. Finally, you'll need to tip it and pour the rest of the water into a bucket through the same hole you bled it from. For more tips, including how to reconnect your radiator, read on!
Reader Success Stories
"It made the task of radiator removal in easy to understand with visuals."
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
