How to Remove Acrylic Paint from Wood

Acrylic paint is water-based and can be removed from wood using a variety of methods. Though dealing with a paint spill immediately after it happens is best, you can remove both wet and dry paint using soap and water, rubbing alcohol, a heat gun, solvents, or sandpaper.

Method 1

Method 1 of 5:

Using Rubbing Alcohol

Download Article

Try to gently chip off as much of the top layer of paint as possible. Any paint you can remove this way will be less paint that the alcohol has to cut through. Be careful not to dig into the wood and leave scratch marks behind.
Use basic rubbing alcohol, which can be purchased at most drugstores or grocery stores. Place the cloth on top of the open bottle and shake it once or twice to saturate a small section of the cloth.
Advertisement
Keep adding alcohol to the cloth and continue rubbing until all the paint is gone. Alcohol can damage the wood's finish, so only use it on the exact area of the paint stain.
Moisten a clean cloth with a bit of water and wipe the area with it to remove all the remaining residue. The wood may still smell of alcohol, but that will dissipate over time.
Rub the damp spot until all excess moisture is removed. The wood will still be wet, but should dry within 24 hours.

Method 2

Method 2 of 5:

Using Soap and Water

Download Article

1
Wipe fresh acrylic paint with a wet cloth. Dampen a washcloth or rag slightly and try to wipe away as much of the paint as you can. Switch out the cloth as needed if it becomes too saturated.
- This may be ineffective on paint stains that have been dry for awhile. Soap and water are most effective on fresh paint stains.
Use a basic glycerin soap, like dish soap, that will produce a good lather and get into the grain of the wood. You can use liquid or bar soap for this.
Keep scrubbing and adding more soap until all the paint is gone. Rub the cloth in straight lines with the grain of the wood to try and get all the paint out of the grooves.
Continue to wipe at the spot until the soap suds are gone. You may need to rinse the cloth once if the spot was really soapy.
Wipe away as much excess water as possible. The wood will remain damp, and may take up to 48 hours to fully dry depending on the size of the spot.^{[1]XResearch source}

Method 3

Method 3 of 5:

Using a Heat Gun

Download Article

1
Determine if the painted area is large enough to use a heat gun. If you're removing paint from an entire door or piece of furniture, using a heat gun may be worthwhile. If you only need to remove a few small spots, then other methods, like soap or alcohol, may be a more practical choice.
- If you decide to use a heat gun and wish to buy one, they are relatively inexpensive and can be purchased at craft stores and hardware stores.
2
Read all product instructions carefully. You can char the wood, and even start a fire, if you use too high a setting. Read the safety instructions to be sure you know the proper way to use the heat gun.
- Melting paint can also create harmful vapors, so be sure to wear protective gear like safety goggles and a mask or respirator.^{[2]XResearch source}
Hold it 3-4 inches (7-10 centimeters) away from the stain for about 10-20 seconds at a time. Try moving it in small circular motions to heat a larger area at once.^{[3]XResearch source}
4
Scrape at the stain with a putty knife. While holding the heat gun with one hand, try to get under the stain with the edge of the knife. The paint should begin to soften and peel away. Clean off the putty knife as needed and continue scraping until all the paint is gone.
- Turn off the heat gun any time you set it down to clean the putty knife.
Wait until the wood is no longer hot, and wipe it with a damp cloth to remove any remaining residue. You can add some soap to the cloth for added cleaning power (see method above for full instructions).

Method 4

Method 4 of 5:

Using a Solvent

Download Article

1
Choose a solvent. The most common paint stripper is methylene chloride. It’s extremely potent and should be used with care. There are solvents that are citrus-based and more environmentally friendly, but these are still dangerous and proper safety precautions should be taken.^{[4]XResearch source}
- Solvents can be purchased at your local hardware or paint store.
Wear eye protection, like safety glasses or goggles, and a ventilation mask to protect yourself from the harmful vapors. It’s also a good idea to wear gloves and long sleeves since the product could splash.^{[5]XResearch source}
Work outside if possible, but if the wood can’t be moved, open all windows and doors. Set a fan behind you so that the airflow blows the fumes away from you and out a window or door.
Use a paintbrush or paint roller to apply a thin coat of the solvent to the paint. Allow it to sit for about 20 minutes, or however long the instructions recommend.^{[6]XResearch source} The paint will begin to bubble as the solvent is working.
Use a blunt plastic scraper to scratch off the paint that has begun bubbling and peeling. Avoid using sharp metal tools that will gauge the wood. Collect the peeling paint in a disposable container or plastic bag.
Some manufacturers claim that water alone will clean the area, but the best way to ensure the wood is neutralized is to wipe it with a rag soaked in mineral spirits.^{[7]XResearch source}
Give the wood at least a week to completely dry and air out before you attempt to apply any stains or waxes.

Method 5

Method 5 of 5:

Sanding the Wood

Download Article

1
Rub the paint using steel wool or sandpaper. Use #0000 steel wool or fine sandpaper (150-180 grit). If there’s a lot of paint to remove, start with a coarser sandpaper, like 80-120 grit or, in extreme cases, 40-60 grit.^{[8]XResearch source} Do this very gently to remove only the paint.
- Large areas can be sanded with power sanders, but be sure to wear a protective mask and safety glasses and read all product instructions carefully.
Run a wet rag over the wood to wipe away sawdust and debris. Swap the cloth out for a fresh one if it becomes too dirty while you’re cleaning.
Once it’s dry again, touch up the wood using the same finish or stain that was used on it before. If you don’t have any extra or don’t know what was used on it, try to match it as closely as possible with samples from your local hardware store.

Expert Q&A

Search

Add New Question

Question
Are there any other products I can use to do this?
Crystal Chadwick
Licensed General Contractor
Crystal Chadwick is a Licensed General Contractor and the Owner of Yin & Yang Construction out of Salt Lake City, Utah. With over 16 years of experience in the construction industry, she specializes in remodels, repairs, and handyman services. Crystal leads her team with vision and a detail-oriented approach, allowing them to provide quality work and design to their clients.
Crystal Chadwick
Licensed General Contractor
Expert Answer
You could use some Goof-Off, but it might damage the finish of the wood. If you go that route, you may need to touch up the finish in that spot.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 1
Question
How do I remove an acrylic stain from wood without stripping or sanding?
Community Answer
Razor it down, there will still be acrylic in the grain. Follow up with a cotton swab and thinner.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 10 Helpful 3
Question
How do I remove an acrylic spill from wood without stripping or sanding?
AutumnBomb
Community Answer
Razor it down, there will still be acrylic in the grain. Follow up with a cotton swab and thinner.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 2