How to Recharge the Air Conditioner in a Car

If your car’s air conditioner isn’t blowing cool air, then you’ve likely lost some of the refrigerant, usually due to a leak. You can recharge the system yourself with a charging kit and some refrigerant, as long as your car uses r134a refrigerant.^{[1]XResearch source} First, you’ll need to check for leaks. Then, check the refrigerant pressure and test your system. Finally, you can add your refrigerant and finish the recharge. If you have a hybrid or electric car, don’t try to recharge the air conditioner yourself, as it can result in a lethal electric charge.

Get Car Support Solve Any Problem

Hi there! Do you have a question about how to diagnose or fix a problem with your car? I’ve read the manual so you don’t have to. Select your make, model, and year, then ask away!

*

Part 1

Part 1 of 5:

Repairing Leaks

Download Article

1
Spray soapy water onto the air conditioner components to locate leaks. You can use dish soap and tap water. Make sure the whole system is coated so that you won't miss a leak. If there are leaks, you'll see bubbles forming around the leak.^{[2]XResearch source}
- Spray bottles are sold at most department stores and online.
- You can also buy a leak detector kit from your local automotive store or online. Follow the directions for that kit.
2
Watch for bubbles to appear, which indicate a leak. The leak will interact with the soapy water to create foam. If you see just a few bubbles or they take a while to appear, then your leak is probably small. If you see a lot of foaming, then you probably have a big leak.^{[3]XResearch source}
- Big leaks will require a professional repair.
Advertisement
3
Use a recharge kit with a sealant to repair small leaks. You can spend more than $1,000 trying to find and repair a small leak, so it’s often better to use a product that contains a sealant. This will help your system hold its recharge longer, as the refrigerant won’t leak out as quickly.
- Look for a product that says its sealant is a conditioner, which won’t clog your pipes. A sealant that has a goo texture can cause a clog.^{[4]XResearch source}
4
Have big leaks fixed by a professional technician. You should not try to fix them yourself, as you could damage the whole system. Not only that, you may leak dangerous chemicals from the car onto the ground.^{[5]XTrustworthy SourceUnited States Environmental Protection AgencyIndependent U.S. government agency responsible for promoting safe environmental practicesGo to source}
- Recharging a system with a big leak is a waste of time and money. It’s best to get a professional to fix it.

Part 2

Part 2 of 5:

Checking the Pressure

Download Article

1
Put on your eye protection and gloves. Refrigerant is very dangerous and can result in injuries. It can cause frostbite if it hits your skin. If you get it in your eyes, it can blind you.^{[6]XResearch source}
- Follow all instructions on the label, including additional recommended protective gear.
2
Find the low-pressure line port, which will have thicker tubing. There are two ports on your air conditioner. You will add the refrigerant to the low-pressure line port, not the high-pressure line port. The low-pressure line has larger tubing than the high-pressure line, making it easy to distinguish between the 2.^{[7]XResearch source}
- Sometimes they are labeled with “H” for high and “L” for low. In some vehicles, the low-pressure line port will be lower than the high port, but this is not always the case.
- Most kits have a hookup that only fits onto the low-pressure port, making it easier to choose the right port.
The cap is the little plastic cover that seals the valve. Once it’s off, make sure you put it somewhere safe so that you don’t lose it.^{[8]XResearch source}
4
Hook the pressure gauge hose to the port. Simply click the gauge connector over the open port. You can wiggle it gently to make sure it’s attached.^{[9]XResearch source}
- If it’s loose or comes off, try to attach it again.
- It’s best to select a recharge kit that comes with a pressure gauge. This allows you to easily add more refrigerant without overcharging your air conditioner.^{[10]XResearch source}
5
Check the reading on the pressure gauge. The gauge will provide a reading in psi. It should have colored zones to indicate if it’s in a safe range. Green means good, but your levels could still be lower than necessary to cool your car if it’s low in the green zone.^{[11]XResearch source}
- Your ideal pressure will be determined once you test the outdoor temperature. You’ll do this when you test your system later in the recharge process.
A reading of 0 means that there is no refrigerant left in your air conditioner, which will require a repair by a professional technician. Otherwise, you can charge the system yourself using your charging kit.^{[12]XResearch source}

Part 3

Part 3 of 5:

Testing Your System

Download Article

1
Crank your engine and turn the AC on high cool, high fan. This allows you to check to make sure your parts are working. It’s okay if your air conditioner is blowing warm or hot air at this time.^{[13]XResearch source}
- Your hood should still be up.
2
Make sure the compressor clutch is spinning. The compressor clutch looks like a circle. It may spin fast or slow, depending on how well your system is working, as well as how much refrigerant is present in the system.
- If it’s not spinning, then you can add half a can of refrigerant and check it again. If it’s still not spinning, then you’ll need to take your car in to a professional technician.^{[14]XResearch source}
3
Set the refrigerant temperature gauge to the ambient temperature. The gauge will tell you what your refrigerant pressure should be after you complete your recharge. This is your recommended pressure level. As you recharge the air conditioner, you can monitor the pressure on your pressure gauge.
- It’s okay to round up or down to the nearest 5 degrees.^{[15]XResearch source}
4
Check the pressure gauge to make sure it’s in the white or green zones. The current pressure level should be below the recommended level you just determined, based on the temperature gauge reading that you took. If it’s above the recommended level or in the red zone, you need to take your car to a technician because something else is wrong.^{[16]XResearch source}
- Do not add more refrigerant if the levels aren’t low. This could damage your car.
5
Turn off the vehicle before adding refrigerant. After you finish testing your system, it’s best to turn off your system, unless the directions on your charging kit say otherwise.
- Always follow the directions on your charging kit to ensure that you get the best possible results.

Part 4

Part 4 of 5:

Adding Refrigerant

Download Article

1
Unscrew the trigger from the can to remove the inner cap. The inner cap is what keeps the refrigerant trigger from piercing the can before you’re ready to use it. You should see where the can screws into the trigger, as it will have a typical joint.^{[17]XResearch source}
- Discard the inner cap.
2
Screw the top back on, which will pierce the top of the can. There will be a metal pin inside the trigger. As you screw the can back on, press hard so that the metal pin pierces the top of the can. You should hear the pressure release inside the can. It will now be ready for use.^{[18]XResearch source}
- If the trigger pin doesn’t pierce the can, then you won’t be able to use the product. In the rare event this happens, you can try removing the trigger and pressing down harder as you replace it again.
3
Shake the can to mix the contents. Vigorously shake it up and down. This will ensure that all of the additives are blended so that you get an even application as you recharge the air conditioner.^{[19]XResearch source}
- If the ingredients aren’t mixed well, you can experience some clogging as you use the product.
4
Connect the refrigerant to the low-pressure line port. You may need to pull back on the edge of the connector to make it fit around the port. Push down until the kit attaches to the port. You can wiggle it gently to make sure it’s fully attached.^{[20]XResearch source}
- If it feels loose or comes off, try again.
5
Squeeze the trigger on your refrigerant. This will release the refrigerant into your air conditioner. Maintain a firm grip as you hold the can.^{[21]XResearch source}
- If your can has a knob instead of a trigger, you should turn the knob until the refrigerant releases into the hose. You should hear it.
This should be a gentle motion so that the ingredients stay mixed. Don’t move it too aggressively, however, as you might accidentally pull it free.^{[22]XResearch source}
7
Check the pressure after 10 seconds of charging. Let go of the trigger and look at the pressure gauge. It’s important that you not put too much refrigerant into your air conditioner.^{[23]XResearch source}
- If your can has a knob instead of a trigger, then you should turn the knob to close the valve after 10 seconds.
- You’ll probably need to add refrigerant a few times to reach the desired pressure. Take your time, though, so you don’t overcharge the system. Overcharging makes your system run ineffectively and can damage it.
Squeeze the trigger for 10 seconds at a time. Gently move the can back and forth as you charge the air conditioner. Remember to check the pressure often.^{[24]XResearch source}

Part 5

Part 5 of 5:

Finishing the Recharge

Download Article

1
Detach the refrigerant connector from the port. You may need to pull up on the collar around the connector to break the seal. Then, remove the connector and place your charging kit in a safe location.^{[25]XResearch source}
- If your can has a knob instead of a trigger, turn the knob, closing it tightly, before you detach the connector.
- For example, you might store it in a cool spot in your garage that is away from heat sources.
2
Replace the port cap on your air conditioner. Screw the cap back onto the left pressure line port. This will prevent debris from getting into your pipes.^{[26]XResearch source}
- This is the cap you removed at the beginning and put in a safe place.
3
Test your air conditioner to make sure the air is cold. It should feel cold on your skin. You can check the exact temperature using your temperature gauge. It should be blowing between 38 to 45 °F (3 to 7 °C).^{[27]XResearch source}
- If it’s still not cold, you’ll need to take your car in to get checked by a professional.

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Things You’ll Need

Eye protection
Gloves
Charging kit
Can of refrigerant (may be in kit)
Pressure gauge (may be in kit)

Tips

Check your owner’s manual or the stickers under your hood if you’re not sure which refrigerant you should use.^{[28]XResearch source}
Thanks
Helpful0 Not Helpful0
Most cars made after 1993 use this refrigerant, and you can convert your car’s system, if necessary.
Thanks
Helpful6 Not Helpful1
Try to get a kit that includes a pressure gauge, which will make troubleshooting and charging easier.
Thanks
Helpful1 Not Helpful1

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

R-12 refrigerant is no longer used because it contains CFCs and is harmful to the environment if it gets out of the system. Don’t try to use old R-12 if you find some, as it is illegal in some areas.
Thanks
Helpful2 Not Helpful3
Do not try to recharge a hybrid! If you use the wrong products, it can result in a lethal electric charge. Instead, take it to see a technician.^{[29]XResearch source}
Thanks
Helpful0 Not Helpful0
Refrigerant can cause injury, such as frostbite, if you use it incorrectly.^{[30]XResearch source}
Thanks
Helpful0 Not Helpful0
Leaving your leak unfixed can harm the environment.^{[31]XTrustworthy SourceUnited States Environmental Protection AgencyIndependent U.S. government agency responsible for promoting safe environmental practicesGo to source}
Thanks
Helpful0 Not Helpful0