How to Preserve Roses in Resin

Instead of throwing away that beautiful bouquet of roses, use them to create a keepsake you can enjoy for a long time to come. By preserving roses in resin, you can make paperweights, decorative accents, or personal gifts to give to others. It’s best to use dried roses so their coloring stays vibrant, and it takes about 5-10 days to dry them by hanging them upside down. After you’ve dried the roses, you should be able to complete this project from beginning to end within 4-5 hours.

Part 1

Part 1 of 3:

Drying the Roses

Download Article

1
Choose roses at the peak of their bloom for the most vibrant color. Avoid picking roses that haven’t opened up yet or that are already starting to brown or droop. You can either buy roses from a store or cut them from a rose bush.
- If you’re cutting your own from a rose bush, it’s a good idea to wear garden gloves to protect your skin from the thorns.
2
Trim away the majority of the leaves from the roses’ stems. Either pull the leaves off by hand or use a pair of scissors to cut them off where they intersect with the stem. You could also shave off the thorns if you’re worried about getting pricked by them.^{[1]XResearch source}
- Leaving a few leaves in place will give you the chance to incorporate them into your design if you want. They can add a nice pop of color against the rose.
Advertisement
3
Wrap a piece of twine around the stem of each rose and tie it in a bow. Use a 6 to 8 inches (15 to 20 cm) piece of twine and wrap it around 3-4 times before tying the bow. Make the bow as tight as possible so the bundle of roses won’t come apart once it’s hanged.^{[2]XResearch source}
- If you don’t have twine, a rubber band will work just as well. Just wrap it around several times until it’s tight against the stems.
4
Hang the roses upside down in a dry, airy place. Keep them out of sunlight so their color doesn’t fade. Put them in a closet or cupboard where there isn’t a lot of moisture in the air, and simply hang them from a hook or nail.^{[3]XResearch source}
- Excessive moisture could keep the roses from drying and could even cause them to grow mold.
Roses don’t take very long to dry, so you should be ready to move on with your project within 1-2 weeks. When you touch the roses, they should feel crispy and the petals should no longer be soft or pliable.
Using Dried Roses versus Fresh Roses: The color of dried roses will remain just as vibrant after they’ve been preserved in resin. You can use fresh roses, but keep in mind that the coloring will fade and look extremely washed out.
6
Cut the stem away from the bud of the roses after they have fully dried. Once you’re ready to start the preservation process, trim away the stem. If you want to use any of the leaves, cut them off and set them to the side along with the rosebuds.
- The stem would most likely just get in the way and be too long to fit in the mold properly.
7
Use a convection oven to dry roses in 3-4 hours. Lay the roses out on a clean baking sheet and preheat the oven to 100 °F (38 °C). Place the baking sheet on the lowest rack and leave the roses in the oven for 2-3 hours. Check them after that time and add an additional hour if they aren’t dry yet.^{[4]XTrustworthy SourceEDISElectronic database of the University of Florida Institute of Food and Agricultural Sciences's peer-reviewed articlesGo to source}
- A normal oven may not be able to go as low as 100 °F (38 °C) and often has more moisture than a convection oven. You can still try this method with a normal oven, but be aware that you may not get the same results.
8
Dry roses in 1-2 days with desiccant in the microwave. Bury roses in a microwave-safe container filled with desiccant. Microwave the container along with a mug full of water for 2 minutes. Poke through the desiccant with a toothpick to check the roses, and continue microwaving them in 1-minute intervals until they’re fully dry. Carefully remove the container and let it sit for 24 hours before removing the roses.^{[5]XTrustworthy SourceEDISElectronic database of the University of Florida Institute of Food and Agricultural Sciences's peer-reviewed articlesGo to source}
- A desiccant is any substance that can be used as a drying agent. There are several options you can use, but silica gel is the fastest. You can buy it at most garden supply stores.

Part 2

Part 2 of 3:

Preparing the Resin

Download Article

1
Use clear polyester casting resin for the cheapest option. This type of resin will dry clear so you’ll be able to see the rose inside really well. It also dries a little slower than epoxy resin, which means you have a little more time to arrange the rose and perfect your craft.^{[6]XResearch source}
- You can find this product at most craft stores or you can order it online.
2
Choose an epoxy resin if you want an amber cast to the finish. Epoxy resin is typically a little faster-drying and longer-lasting than polyester resin, though both options should create keepsakes that will last for years. If you like the idea of a lightly tinted finish, epoxy resin is the way to go.^{[7]XResearch source}
- You can also buy clear epoxy resins, but the cost is much higher than what you would pay for a clear polyester resin.
3
Work in a well-ventilated area to combat the resin’s strong odor. Once your roses are dry and you’re ready to complete your project, set up your tools outdoors if possible. If you do have to work inside, open up as many windows as you can and use a fan to circulate the air faster.^{[8]XResearch source}
- If you’re sensitive to strong smells, consider wearing a face mask while you work.
4
Wear rubber gloves to protect your hands from the resin. If you do happen to get resin on your fingers, simply rinsing them with water won’t get it off completely and the resin will leave a sticky residue. Safely remove resin without using harmful chemical products by doing the following:^{[9]XResearch source}
- Mix 1/2 tablespoon (4.5 grams) of poppy seeds with 1 tablespoon (15 mL) of dish soap. Rub the mixture into your hands for 60 seconds without adding water. Then add water, wash your hands, and scrub away any remaining resin. The poppy seeds act as an exfoliant to rough up the resin and get it to detach from your skin.
- If you don’t have poppy seeds, coffee grounds would also work.
5
Measure how much resin your mold will hold. Your mold may have this information printed on it, but if not, you can figure it out yourself. Simply pour water into the mold and then pour that water into your measuring cup to see how much liquid there is.^{[10]XResearch source}
- You can buy molds at most craft stores or online.
- Plastic molds work just fine, but you could also invest in latex-rubber molds, which are more flexible and easier to remove once the resin is set.
Tip: Make sure the mold you chose is deep enough to contain the rose you want to preserve. Choose one that is at least 1.5 to 2 inches (3.8 to 5.1 cm) deep
6
Pour enough resin into the disposable measuring cup to fill the mold. You can buy disposable measuring cups online, at craft stores, or at most local grocery stores. Look for ones that include measurements on the side so that it’s easy to pour the right amount of resin.^{[11]XResearch source}
- Because the resin is so hard to clean off, disposable measuring cups guarantee that you won’t accidentally ruin your normal measuring cups.
7
Add the catalyst to the resin per the instructions on the resin container. In general, the catalyst makes up 1-2% of the total volume of the resin, so if your mold holds 4 ounces (110 g), you would need to add about 16 drops of resin. The resin container should have a chart on the back that gives you a breakdown of how much to use.^{[12]XResearch source}
- The catalyst heats the resin and helps it harden, or cure. Without it, your mold would never harden into a beautiful keepsake.
If you don’t have a wooden skewer, use something else that is also disposable, like a plastic spoon or popsicle stick. It’s important you mix things well so that the catalyst gets activated.^{[13]XResearch source}

Part 3

Part 3 of 3:

Creating the Mold

Download Article

1
Pour the stirred resin into the mold. After stirring together the catalyst and resin for 60 seconds, carefully pour the mixture into the mold you’ve chosen for your roses. Be careful to not drip the resin onto your work surface or get it onto the edges of the mold itself.^{[14]XResearch source}
- If you’re worried about spills, lay some old newspaper underneath your work station.
2
Place the rose into the resin in the design that you want. Depending on the type of mold you chose, be aware of which side will be the top. For example, if you’re using a domed mold, you’ll want to insert the rose into the resin facedown so that it’ll be visible once it’s right-side up. Use the wooden skewer to push the rose into place.^{[15]XResearch source}
- The rose will most likely rise to the top of the resin, and that is okay. Right now, focus on getting it into a general placement. You’ll have a chance to push it deeper in a little while.
- This is also the time to add the dried leaves if you saved any. You could also add other dried flowers.
3
Set a timer for 10 minutes and let the resin set to a gel-like consistency. If after 10 minutes the resin is still very liquid-like, set the timer for an additional 10 minutes. You want the resin to be pliable so you can push the rose in further without it popping back up but not so hard that you can’t make any adjustments.^{[16]XResearch source}
- If you’re working indoors or in a humid climate, it may take closer to 30 minutes for the resin to get to the right consistency.
4
Finalize the positioning once the resin is the right consistency. Use your wooden skewer to push the rose deeper into the resin. If it floated off to the side, you can also push it back into place. Use this time to arrange any other flowers or leaves that are in the mold.^{[17]XResearch source}
- It’s very hard to make roses look bad. Even if things are off-center a little, the end result will still look beautiful.
5
Let the resin set for about 4 hours or until it is completely hardened. Consult the back of the resin container to see how long they recommend for the curing process. It usually takes several hours, but if you made a really large or deep mold, it could take longer.^{[18]XResearch source}
- If the resin is still sticky to the touch, it’s not done. When it’s fully dry, it should be smooth and hard.
6
Remove the mold from the resin to reveal your creation! Loosen the mold from around the resin to pop it out, or peel away the mold if you used a flexible one. Use your mold as a decorative accent around your home, as a paperweight, or give it away as a gift.^{[19]XResearch source}
- The molds should come away clean, which means you can reuse them to make even more!

Video

Read Video Transcript

Expert Q&A

Search

Add New Question

Question
How can I remove a spilled resin?
Shelley Williams
Arts & Crafts Expert
Shelley Williams is an Arts & Crafts Expert based in Long Beach, California. After a 20-year career as an educator, Shelley brought her love of education to the world of crafting and creating things. Shelley opened CRAFT + LIGHT, a creative arts studio, in 2019. Since then, Shelley has taught over 1000 people to make soap, wood signs, alcohol inks, candlemaking, bath bombs, and more. In addition to being a craft store, CRAFT + LIGHT hosts private parties, family birthday events, open studio events, and other types of craft demonstrations. Shelley partners with City governments to curate creative care packages for at-risk residents and is a partner of the Long Beach Black Health Collaborative funded out of the City of Long Beach.
Shelley Williams
Arts & Crafts Expert
Expert Answer
To remove spilled resin that has begun to harden or has mixed onto a surface, act swiftly. If the resin hasn't completely hardened, try using alcohol, as it can help dissolve its sticky consistency. However, if the resin has already mixed with the hardener before it cures fully, promptly wipe it away thoroughly using a paper towel or submerge the affected item in boiling water. This ensures that the resin doesn't permanently adhere to the surface.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 0
Question
Are epoxy resin toxic?
Shelley Williams
Arts & Crafts Expert
Shelley Williams is an Arts & Crafts Expert based in Long Beach, California. After a 20-year career as an educator, Shelley brought her love of education to the world of crafting and creating things. Shelley opened CRAFT + LIGHT, a creative arts studio, in 2019. Since then, Shelley has taught over 1000 people to make soap, wood signs, alcohol inks, candlemaking, bath bombs, and more. In addition to being a craft store, CRAFT + LIGHT hosts private parties, family birthday events, open studio events, and other types of craft demonstrations. Shelley partners with City governments to curate creative care packages for at-risk residents and is a partner of the Long Beach Black Health Collaborative funded out of the City of Long Beach.
Shelley Williams
Arts & Crafts Expert
Expert Answer
Epoxy resin can be toxic, particularly for pregnant women, so it's important to avoid exposure to it. Even though it's commonly used as a beginner resin due to its ease of use, safety precautions must still be taken seriously. While teaching classes, I emphasize the importance of wearing goggles when working with epoxy resin, as prolonged exposure can have adverse health effects. However, compared to professional-grade resin bases like polyurethane, epoxy resin is considered less toxic.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 1

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Put a felt bottom on the completed mold if it’ll be on top of a hard surface that you want to protect from potential scratches.^{[20]XResearch source}
Thanks
Helpful0 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!