How to Make a Rope Ladder

Knowing how to make a rope ladder is a very handy skill. Not only do they have a practical use in outdoor activities such as boating and hiking, but they’re a lot of fun to climb, too. Additionally, they may be used as an emergency resource where traditional ladders are unavailable, impractical, or unwieldy.

Method 1

Method 1 of 2:

Making A Basic Single-Rope Ladder

Download Article

Take hold of the rope on the end of the right side of the "U" and slide your hand down the rope to measure out 1 foot (30 cm) of rope. ^{[1]XResearch source}
Bring your hands together to squish the "S" down horizontally. ^{[2]XResearch source}
Advertisement
Make the first rung of the ladder by taking the left end of the rope and threading it through the first, left bend of the "S." Bring the end of the rope under the bottom curve, wrapping it around the whole "S" four times. Feed the end of the rope through the second, right bend of the "S" to secure the tie and complete the first rung. ^{[3]XResearch source}

Method 2

Method 2 of 2:

Making a Rope Ladder With Wooden Rungs

Download Article

1
Prepare two lengths of rope by binding or melting them at the ends. Do this to prevent your newly cut rope from fraying or unraveling.
- Binding the ends of a rope is called whipping. Take some twine and run it along the length of the rope until you almost get to the rope’s end. Double back when the length of the twine is equal to around one and a half times the diameter of the rope. The twine should form an upside down “U” shape. Wrap the twine tightly along the “U”, and put the end of the twine through the loop at the top. Now, pull both ends of the twine until the loop is pulled underneath the whipping. Cut the ends of the twine so that they don't stick out and the whipping looks neat. ^{[4]XResearch source}
- It is best to use natural fibre twine when whipping natural fibre rope as it will be less likely to slip off. ^{[5]XResearch source}
- If you are using a synthetic rope, wrap the ends with some tape, then melt them over a flame. ^{[6]XResearch source}
2
Lay the rope flat on the ground, and make an overhand loop around 15 inches (38 cm) from the top-end of your rope. To make an overhand loop, take the working end of the rope and place it over the standing part. This loop is the first step of forming the knot which will hold the first wooden rung.
- The working end of the rope is the part of the rope which is being actively used to form a knot. ^{[7]XResearch source}
- The standing part of the rope is the portion of the rope which is not being actively used to form a knot. It is all of the rope in the opposite direction of the working end. ^{[8]XResearch source}
To do this, first put your fingers through the underside of the loop, and grasp the standing part. Now, pull the standing part through the overhead loop. This should form a new loop.
4
Insert a wooden rung into the new loop formed by the standing part and tighten the rope. Move the rung into the desired position, and tighten the rope. ^{[9]XResearch source} The resulting knot should be visible on the top and the bottom of the rung.
- The rung will be fairly secure at this point, but tying an overhand knot beneath it will greatly decrease any likelihood of the rung moving down the rope. To tie an overhead knot, make an overhand loop, then pass the working end over, then through the loop. ^{[10]XResearch source} Make sure the overhand knot is directly below the knot supporting the rung.
Take care to make sure that your rungs are level. Crooked ladder rungs will increase the likelihood of a fall.
Space your rungs uniformly, and in a manner that will allow you to climb comfortably. Keep adding rungs until your ladder reaches the desired length. ^{[11]XResearch source}
7
Secure your ladder at the top. To do this, use either a timber hitch or a rolling hitch knot.
- To tie a timber hitch, wrap the working end around the pole or branch you intend to attach your ladder to all the way around once. Cross the working end over the standing part and continue to wrap the working end around the pole at least twice more. Pull the rope taut to tighten it. If you need more grip, wrap the working end around the standing part a few more times. A timber hitch is ideal for attaching a rope ladder because the greater the amount of pulling force exerted on the knot, the tighter it becomes. ^{[12]XResearch source}
- To tie a rolling hitch, take the working end of the rope and wrap it completely around your stake at least three times. Take the working end and place it over the standing part. Now wrap the rope around the stake on the other side of the standing part a few times. Tuck the working end underneath the bit of rope which crossed over the standing part and pull it tight. A rolling hitch holds up very well against a horizontal pulling force, so it is ideal if you are attaching your ladder to horizontal stakes or poles. As with the timber hitch, if more grip is required, wrap the working end around the pole a few more times. ^{[13]XResearch source}
8
Secure your ladder at the bottom. This is optional, but securing your ladder to the ground will greatly increase its stability and make it easier to climb. ^{[14]XResearch source}
- If you are going to secure your ladder to the ground, be sure to leave enough rope to do so; 15 inches (38cm) or more should do the trick.
- Wrap each leg of your ladder to a stake at a 45-degree angle and secure it with a rolling hitch.

Video

Read Video Transcript

Community Q&A

Search

Add New Question

Question
Where can I buy a rope ladder?
Community Answer
Online is probably the best option. You may also want to check Home Depot or Lowe's.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 7
Question
Can you drill a hole at the rungs of a ladder and tie a knot underneath to stop the rung from slipping?
Community Answer
You can drill it as long as the rope is thick. You can't really tie a knot underneath. Instead, you could try digging it into the ground.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 22 Helpful 8
Question
Is this strong enough for African grey parrots?
Emma Erasmus
Community Answer
Yes, definitely. As long as you use proper rope and make sure the wood is safe, you should be fine.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 6

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Natural fibre rope such as hemp or manila will grip the wood of rungs and trees better than synthetic rope. ^{[15]XResearch source}
Thanks
Helpful0 Not Helpful0
Be sure to construct your rope ladder out of rope that is sturdy enough to hold a person's weight. Most ropes purchased at a store will display the maximum load weight on the packaging.
Thanks
Helpful16 Not Helpful5
Check your rope regularly for wear and tear. Replace it when it gets frayed.
Thanks
Helpful26 Not Helpful12