How to Make a Rabbit Snare

Whether you are lost in the wild and need food, want to capture the pests in your garden, or just want to learn trapping, rabbit snares are an easy and essential wilderness skill. Though there are a lot of methods and variations, all snares work by creating a noose that tightens under the weight of a hopping rabbit.

Method 1

Method 1 of 3:

Building a Free-Standing Snare

Download Article

You want roughly 2.5 feet (0.8 m) of wire to create your snare. While you can use any long, bendable string, usually a steel or aluminum wire works best.
Bend one end of the wire around your finger to create a small loop roughly 1 inch (3 cm) across. The end of the wire will bend back on itself so there are roughly 2–3 inches (5–8 cm) of extra wire at the bottom of the loop. This is your slip-knot loop.^{[1]XResearch source}
Advertisement
3
Twist the end of the wire to hold it in place. Wrap the excess wire from the loop around the wire at least 5-6 times to snugly secure them together. Imagine braiding two pieces of rope or hair snuggly together. This is the most important part of the trap, and the loop needs to be strongly attached. When done it will resemble a balloon on a string or the head of a needle.
- Put a pencil into the loop and then try to pull it apart. It should hold firm under a fair amount of pressure.
- You can use pliers to clamp the wires together for added stability.
Feed the opposite end of your wire into the small loop you just made, like threading string through the top of a needle. Your wire will now resemble a large circle with the both ends of the wire close together.^{[2]XResearch source}
Keep pulling until the wire circle is roughly the size of your fist, around 6–7 inches (15–18 cm) across. Your wire will look like a yo-yo on the end of a string, with the wire on one end and your small noose on the other. The bottom wire should meet the noose at the slip-knot loop.
This will keep your trap in place once a rabbit runs through it. The hole should be roughly 8–10 inches (20–25 cm) off of the ground once you secure the post in the ground.
7
Secure the wire to the stake. Feed 3–4 inches (7.6–10 cm) of wire through the hole in the post and then wrap it around so that it meets the rest of the wire. Braid the end of the wire to the rest of the wire, making a balloon shape like the one used to make the slip-knot loop.
- You can also tie the wire to the post, or use a staple gun to secure it to the wood.
- You want to have roughly a foot of wire between the post and your snare.
- Tug on your wire to make sure it is attached to the post and does not come out easily.
8
Drive the post into the ground. Find a small path where you’ve seen rabbits in the past and secure the post into the ground. Use a hammer to firmly stick the trap in place – it shouldn’t move or come out easily. You can also play your trap near fences or gardens, at the edge of high grass, or in the underbrush.^{[3]XResearch source}
- Make sure the post is driven into the ground firmly – if the rabbit can pull it out of the ground they will escape.
Think of your noose as a target you want the rabbit to hit mid-jump. When the rabbit hops through the loop, it will pull the noose tightly shut, killing the rabbit.

Method 2

Method 2 of 3:

Building a Hanging Snare

Download Article

1
Cut a 2.5ft piece of wire, rope, or cord. This is the wire that will capture and kill the rabbit in your snare, so it needs to be strong enough to hold the animal. While you can use any long and bendable wire, a thin metal wire works best.
- While easier to work with, rabbits can chew threw many thin ropes and cords, making metal the best option.
Bend one end of the wire back on itself to create a simple loop, no bigger than an inch. You can wrap the wire around your finger to get the shape and size right. There should be roughly 2–3 inches (5–8 cm) of extra wire at the bottom of the loop. This is your slip-knot loop.^{[4]XResearch source}
3
Twist the end of the wire at the bottom of the loop to hold it in place. Wrap the excess wire from the loop around the wire at least 5-6 times to snugly secure them together. This is the most important part of the trap, and the loop needs to be strongly attached. When done, it will resemble a balloon on a string.
- The best way to test the strength of your loop is to put a pencil into the loop and then pull it apart. If the loop comes undone then you should retwist the wire to create a stronger loop.
- Use pliers to clamp the wires together for added stability if you need it.
Feed the opposite end of your wire into the small loop you just made. Your whole wire will now resemble a large circle.
Pull the end of the wire through the loop, shrinking your circle until it is the size of your fist, roughly 6–7 inches (15–18 cm) across. Your wire will look like a yo-yo on the end of a string.
6
Place a branch, felled tree, or bar horizontally over the ground. It should be elevated roughly a foot off the dirt and placed in a narrow corridor, such as a small footpath or a trampled trail in the forest. Your snare will hang from this to trap the rabbit.^{[5]XResearch source}
- Felled trees, low hanging branches, or iron bars will all work.
- Make sure your bar is secured or heavy enough that a small rabbit couldn’t pull it away.
The loop should be hanging from the trap so that it is 7–8 inches (17.8–20.3 cm) off of the ground. Your trap will resemble a noose hanging from a rafter or bar. As the rabbit jumps through the loop its weight will pull the loop tightly shut and kill the animal.
Using large branches, block off the space underneath and to the sides of your snare, forcing them to jump through your loop. You want to block off all the space except the one in your snare.

Method 3

Method 3 of 3:

Placing Your Traps Effectively

Download Article

One of the best places to put a trap is in the holes rabbits use to enter your property. If your fence has openings that rabbits use regularly, fit the loop of your snare right in the hole and wait for them to come back.
2
Place traps near small, beaten paths. Rabbit trails will show grass that has been stepped down repeatedly, little tracks in the dirt, and patches of mud. If you could walk through it, then rabbits will likely use it at some point to navigate the forest.^{[6]XResearch source}
- Look for openings in tall grass, muddy paths, or known rabbit holes.
Trapping is a numbers game; the more snares you set, the more rabbits you will get. Separate them by a few hundred yards to increase your chances of successful capturing.
4
Make sure your snares are the right height. The snare works by catching the rabbit mid-hop so that it pulls the snare tight as it returns to the ground. You want your snare to be 6–8 inches (15.2–20.3 cm) off of the ground.
- Remember that a rabbit needs to fit its head and ears into the trap. Most rabbits are 6–7 inches (15.2–17.8 cm) big from nose to ear tips.
Constantly checking in on your trap scares away wildlife, so be patient. After one day has passed, return to the trap to check if it caught anything. If not, leave and return the next day. If you have still not caught anything, adjust the height of the snare or move it.

Community Q&A

Search

Add New Question

Question
Will this work for possums?
Community Answer
Yes, it should. But keep in mind that possums don't jump as high, and, in fact, usually don't prefer to jump at all. You'll want to put the snare down lower, so that the possum will walk through it.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 12 Helpful 46
Question
How do I make a model of a rabbit snare?
Community Answer
Follow the steps on this page. It's that simple. Just make sure to disarm the trap so you don't trigger it yourself.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 10 Helpful 36
Question
Will this work on hares?
Community Answer
A hare is like a rabbit, but larger. Hang your snare higher, and make the loop larger.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 9 Helpful 38

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Set up several snares increase your chances to catch a rabbit.
Thanks
Helpful20 Not Helpful7
Make sure all of your loops and knots are strong. You can check them by pulling firmly to make sure they don't come apart.
Thanks
Helpful16 Not Helpful6

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

It is illegal to leave traps out for more than a day without checking them.
Thanks
Helpful11 Not Helpful4
In some states, you need a license to set up traps for small game, such as squirrels, opossums, raccoons, and rabbits.
Thanks
Helpful7 Not Helpful2
Self-shutting traps are illegal.
Thanks
Helpful23 Not Helpful26