How to Make a Leather Riding Crop

Crops are often used in horseback riding to train horses and help them learn new commands. Rather than used for discipline, riding crops are used to help encourage horses to perform specific tasks, and are meant to help reinforce the rider's commands. Leather riding crops are both classical and beautiful. They may seem complex to make at first, but with enough practice, are actually quite simple.

Part 1

Part 1 of 5:

Weaving the Base

Download Article

Find a thin, flexible rod made from brass or fiberglass. Cut it down to 2½ feet (76.2 centimeters), or have the store do it for you.^{[1]XResearch source}
2
Cut two pieces of leather lace. Each pieces needs to be 3.5 times the length of the rod. It would be even better if you cut the lace a little bit longer than you need to. Remember, you can always cut the excess off at the end, but you can't add lace back.^{[2]XResearch source}
- Choose leather lace that is flat and wide, like ribbon. Don't use the round, tube type.
- Use thin leather lace. Do not use the thick, suede lace.
Advertisement
Cross both of the leather strands at the center to make an X. Place that X right at the top of the rod, just below the tip.^{[3]XResearch source}
4
Cross the top-right strand behind the rod. Take the top-right strand, and pull it across the back of the rod. Angle it downward so that it comes out between the top-left and bottom-left strands.
- Keep the lace flat. Don't let it twist or turn.
Pull the strand between the two strands on the left. Cross it in front of the rod, back towards the right side.
6
Hold the right strand under the other right strand. The strand that used to be on the top-right is now on the bottom-right. Hold the two strands so that they are parallel to each other.
- Pull on all four strands to tighten them.
Bring the top-left strand behind the rod. Pull it out between the two strands on the right. Cross it over the front of the rod, and back over to the left. Tug on the strands to tighten them.^{[4]XResearch source}
After you wrap each side, remember to tug on the strands to tighten them. Stop weaving when you reach the bottom end of the rod.
Don't tape the ends directly to the rod. Instead, set the rod down on the table, and tape the strands to the table as well. You can also wrap some tape around the strands instead, just below the base of the rod.

Part 2

Part 2 of 5:

Whip Lashing the Ends

Download Article

About 8 to 12 inches (20.32 to 30.48 centimeters) should be enough. You will be using this to whip lash the bottom of your rod.^{[5]XResearch source}
Fold the thread in half first, so that the ends match up. Place it against the bottom 2 to 3 inches (5.08 to 7.62 centimeters) of the rod. Make sure that the folded part of the string is pointing towards the rod, and the tails are pointing away.^{[6]XResearch source}
3
Wrap one of the tails around the rod, towards the fold. Hold both of the tails against the base of the rod. Take one of the tails, and start wrapping it around the base of the rod, securing the thread to it. Keep wrapping until you are about ½ to 1 inch (1.27 to 2.54 centimeters) from the fold.^{[7]XResearch source}
- Be sure to wrap tightly.
Bring the thread under the folded part of the thread, then slide it up through the loop. Do not slide it down through the loop.^{[8]XResearch source}
Find the remaining thread tail hanging off of the bottom of the rod. Give it a tug until the loop disappears under the wrapped thread. Keep tugging until about half of the top tail disappears under the wrapped thread as well.^{[9]XResearch source}
Once you can't see the loop anymore, give both threads a sharp tug. Snip the excess off as close to the wrapping as you can.^{[10]XResearch source}

Part 3

Part 3 of 5:

Creating the Handle

Download Article

1
Decide how long you want the handle, then cut four strips of leather lace. Each strip needs to be four times the length of your handle.^{[11]XResearch source} A good way to determine ho long the handle should be is to measure the width of your palm, then add 2 inches (5.08 centimeters).
- Use the same type of leather lace as you did for the rod. It can be the same color or a different one.
2
Weave the four strips into an X in front of the rod. Place two of the strips at an angle in front of the rod, going from the top left to the bottom right. Take the third strip, and weave it over and under across the first two strips. Take the fourth strip, and weave it under and over across the first two strips.^{[12]XResearch source}
- Adjust the strips to make an X shape. You will have two strips on each arm of the X.
Take the top-right strip, and pull it behind the rod. Weave it under and over, under and over the strands on the left, starting from the one on the top.^{[13]XResearch source}
Position it right beneath the other three right strands. This is almost like weaving the covering for the rod, but you don't want to tighten the strands just yet.^{[14]XResearch source}
Take the top-left strand and pull it behind the rod. Weave it under and over, under and over the strands on the right, starting from the top. Pull it across the front of the rod, and back over to the left.^{[15]XResearch source}
Make sure that the strands are where you want the top of the handle to start, then pull on them to tighten them. Make sure that you are pulling the left strands to the left, and the right strands to the right.^{[16]XResearch source}
Alternate between doing the right and left sides. After each right and left set, pull on the strands to tighten them, then continue weaving.
Use the same lashing technique as you did for the base of the rod. Once you have the ends lashed together, trim off all the excess leather lace strands. Coat the bottom of the rod with leather glue, if desired, for extra strength.^{[17]XResearch source}

Part 4

Part 4 of 5:

Adding the Tip

Download Article

1
Cut a small rectangle out of leather. Use a ruler and a chalk or pen to draw an 8 by 2-inch (20.32 by 5.08-centimeter) rectangle. It would be the easiest to do this with a rotary cutter, but you can use a sharp pair of scissors as well.^{[18]XResearch source}
- Use white chalk on dark leather and pen on light leather.
- If your leather has a finished side and an unfinished side, make sure that you are drawing on the unfinished side.
2
Coat the narrow edges of the rectangle with glue. Turn the rectangle so that the unfinished side of the leather is facing you. Coat the top and bottom edges with glue, about 1 inch (2.54 centimeters) for each.^{[19]XResearch source}
- A leather glue would work the best, but you can try using an industrial-strength glue instead.^{[20]XResearch source}
Make sure that only the first inch (2.54 centimeters) or so of the rod is touching the leather, and that it is centered.
You rectangle will now be 4 inches (10.16 centimeters) tall. Make sure that the top and bottom edges of the rectangle are aligned.^{[21]XResearch source}
5
Clamp the edges shut and let them dry. Place a binder clip to each side of the rod sandwiched inside the leather. Leave them there until the glue dries. How long this takes depends on the type of glue you used; it will typically take a few hours.^{[22]XResearch source}
- Once the glue dries, you can remove the clamps.
Coat the bottom inch (2.54 centimeters) of the leather rectangle with more glue. Fold the left and right edges towards the middle, making sure that the bottom edges are aligned. This will cause the leather rectangle to flare and taper outward towards the top.^{[23]XResearch source}
Use the same method as you did for the base of the rod and the handle.

Part 5

Part 5 of 5:

Making the Strap and Covering the Lashing

Download Article

How long you make this braid is up you you, but it should be long enough to loop over your palm. Leave a few inches/centimeters at the top and bottom of the braid un-braided so that you can secure it to the handle.^{[24]XResearch source}
Fold the braid to make a loop, then position it over the top of the handle. The folded part of the strap should be pointing to the rod's tip, and the loose tail ends should be pointing to the base. Whip lash the strap down using the same technique as you did for the base of the rod, the base of the handle, and the leather tip.^{[25]XResearch source}
Try to cut as close to the wrapped threads as you can. If you ant to, you can coat the wrapped threads with some leather glue for extra strength and durability.^{[26]XResearch source}
4
Cut three, small rectangles out of leather to cover the whip lashing. The strips need to be long enough to wrap around the whip lashed parts at the tip, top of the handle, and base. They need to be at least 1 inch (2.54 centimeters) wide.^{[27]XResearch source}
- If your whip lashing is wider, then make the rectangles wider.
5
Pierce four holes on each narrow end of the leather rectangles. Place the first leather rectangle over a wooden board, then use an awl and a mallet to pierce four, evenly-spaced holes into both of the narrow edges.
- Do this step for all of the leather rectangles.
Cut a long piece of waxed thread of sinew, and string a leather needle onto each end. Pull each needle through the second hole on each side of the rectangle, starting from the inside.^{[28]XResearch source}
7
Saddle-stitch the leather rectangle shut. Push the left needle down through the first left hole, and out the first right hole. Push the right needle down through the first right hole and out the first left hole. Repeat this step until you reach the top of the leather rectangle.^{[29]XResearch source}
- Pull on the thread often to tighten the stitching.
- Move onto the second set of holes, then the third, then the fourth.
This should be enough to hold your leather rectangle together. If you are worried about it coming undone, you can tie knots into the threads before cutting them.^{[30]XResearch source}
This includes the tip of the crop and the top of the handle.

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Consider covering the leather caps with Turk's Head knots. Weave the knots separately, then slip them over the leather caps. Tighten them, then cut off the excess lace.^{[31]XResearch source}
Thanks
Helpful0 Not Helpful0
If you can't find axed thread, you can make your on by running thick, polyester thread across some beeswax.
Thanks
Helpful0 Not Helpful0
If these crops are for kink or BDSM purposes, be sure to practice proper safety, and most important of all: consent.
Thanks
Helpful1 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Use caution when working with leather needles and leather awls. They are designed to easily pierce thick leather—your skin is no exception.
Thanks
Helpful2 Not Helpful0
Never use a riding crop to discipline your horse. A light tap is all your horse needs.
Thanks
Helpful1 Not Helpful1