How.com.vn is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 23 people, some anonymous, worked to edit and improve it over time.
How.com.vn marks an article as reader-approved once it receives enough positive feedback. In this case, 85% of readers who voted found the article helpful, earning it our reader-approved status.
This article has been viewed 567,931 times.
Learn more...
Do you like saving money by building your own bongs? Have you gotten tired of using cheap plastics and spare parts to make a working bong? If so, you might want to step up by making a glass water bong; the glass results in a sturdier container allowing for bigger and more even hits, and it will perform as well as an expensive, store-bought water pipe.
Steps
Pick your bottle. While any glass bottle can be turned into a water bong, some bottles are better than others. Bottles with a long neck and a wide base work best. Getting a clean, perfectly sized hole for the stem is easiest with a bottle that has little curve on the upper slope where the base connects into the stem.[1]
Get the proper drill bit. You'll need a 3/4" diamond drill bit to drill through the glass. Despite having the word "diamond" in the name, these usually only run for about eight to twelve dollars. You might have to order the bit online so make sure you don't leave this step for last.[2]Advertisement
Acquire a downstem, bowl, and grommet. You'll want a 14mm glass bowl and downstem. Choosing the proper length for your downstem is important. Measure the distance from the upper curve of the body of your bottle to the opposite side of the base. Acquire a downstem approximately the same length, and definitely no longer.[3]- Glass downstems and bowls can be found at local head shops or ordered online.
- You'll need a rubber grommet with the following measurements: an outside diameter of 31/32", an inner diameter of 1/2", and a 3/4" groove. These can be found at supply stores like Home Depot, or can be found online.
Clean the bottle. Empty the bottle and wash it out with warm water. Warm water helps the drilling go smoothly. You're going to be drilling in the sink, so make sure that area is clear.
Mark a spot to drill. Remove any plastic that might be on the bottle. Find a spot on the bottle where the surface is relatively flat, somewhere on the upper curve of the body. Place the gasket there and use it to trace a circle with a sharpie.[4]
Prepare your tools. Attach the diamond drill bit to your drill. Be sure to use a battery powered drill, as you will be running water over the drilling area. Since there will be drilling and glass involved, it's a good idea to put on safety googles.[5]
Get a steady stream of water over the drill spot. To keep the glass cool and prevent it from breaking, turn on the faucet. You want more than just a trickle but not such a heavy stream that you can't see what you're doing. Hold the bottle so the water runs over the spot you marked.[6]
Start drilling slowly. Set your drill to 3/4 of its max speed and gently push it against the marked spot. To get a steady drill, first angle the drill bit so it just touches the top of the spot. Slowly angle the drill bit until it's going into the glass at a 90 degree angle, using the carved out edge as a pivot. Once you're nearly through the glass, ease up on the pressure a bit to avoid cracking or breaking the bottle.[7]
Grind away sharp edges and clean out the glass. Use the drill to smooth the edges of the hole. Pour out the water and rinse the bottle several times to clean out the bits of glass. The last thing you want is to inhale glass powder, so don't rush this step.[8]
Put in the grommet, stem, and bowl. Take your 3/4" grommet and work it into the hole. Then run some water over your downstem and slide it into the grommet, carefully, so you don't push the grommet into the bottle.[9] Insert the bowl into the stem, and you've finished!
Expert Q&A
Tips
- Don't rush. Don't rush at all. You will waste many good bottles by rushing and causing them to crack and break.Thanks
- The bigger the bottle, the better the hit. Gallon-sized alcohol bottles are the best. Try to not use short, squat bottles. Instead, use tall, thinner bottles. They force the smoke to travel through more water.Thanks
- There will be glass shards in the bottle after you're done. You don't want those in there for safety's sake; either vacuum them out or try to wash them out with high-pressure water.Thanks
Warnings
- If you're under 18, or afraid of getting caught, or just frequently throw away home-made bongs, making a glass bong really isn't worth your time. If you want a glass bong that can be easily hid, try glass soft-drink bottles or beer bottles.Thanks
- This is glass, so if it breaks, be careful.Thanks
Things You'll Need
- Glass bottle
- Battery-powered drill
- Diamond drill bit
- Sharpie
- Grommet
- Bowl
- Stem
References
- ↑ http://beyondchronic.com/2012/10/make-your-own-glass-bong-how-to-do-it/
- ↑ http://beyondchronic.com/2012/10/make-your-own-glass-bong-how-to-do-it/
- ↑ https://www.youtube.com/watch?v=nSiUIAsX58M
- ↑ http://beyondchronic.com/2012/10/make-your-own-glass-bong-how-to-do-it/
- ↑ http://beyondchronic.com/2012/10/make-your-own-glass-bong-how-to-do-it/
- ↑ http://beyondchronic.com/2012/10/make-your-own-glass-bong-how-to-do-it/
- ↑ https://www.youtube.com/watch?v=nSiUIAsX58M
- ↑ http://beyondchronic.com/2012/10/make-your-own-glass-bong-how-to-do-it/
- ↑ https://www.youtube.com/watch?v=nSiUIAsX58M
About This Article
To make a glass water bong, you'll need a glass bottle, a drill with a diamond drill bit, a downstem, a bowl, and a grommet. First, place the glass bottle in a sink and run cold water over it. The running cold water will prevent the glass from shattering when you drill into it. Then, drill a hole through the body of the bottle. Insert the grommet into the hole, then slide the downstem into the grommet. Finally, attach the bowl to the downstem, and you're done! For tips on how to choose the right glass bottle for your bong, read on.
Reader Success Stories
"I knew how to make a bong, but didn't know the exact measurements. I made a bong and it works great. Thanks for the great article. "..." more
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
