How to Make Glass

Making glass is a very ancient process, with archaeological evidence of glass making dating back to before 2500 BC. Once a rare and prized art, manufacturing glass has become a common industry. Glass products are used commercially and in the home as containers, insulator forcing fibre, lenses and decorative art. While the materials used to make them may vary, the general process for how to make glass is the same and is described below.

Method 1

Method 1 of 2:

Using a Furnace or Kiln

Download Article

1
Obtain silica sand. Also called quartz sand, silica sand is the primary ingredient in making glass. Glass without iron impurities is sought for clear glass pieces, as the iron will cause the glass to appear greenish when present.
- Wear a face mask if handling extremely fine-grain silica sand. If inhaled, it can irritate the throat and lungs.
- Silica sand is available from online retailers. It is fairly cheap - small quantities shouldn't cost more than 20 dollars. If you want to operate on an industrial scale, specialty retailers can offer competitive rates on large orders - sometimes lower than $100 per ton.
- If it is not possible to find sand sufficiently free of iron impurities, their tinting effect can be countered by adding small amounts of manganese dioxide. Or, if you want greenish glass, leave the iron in!
Sodium carbonate (commonly called washing soda) lowers the temperature necessary to make glass commercially. However, it permits water to pass through the glass, so calcium oxide, or lime, is added to negate this property. Oxides of magnesium and/or aluminum may also be added to make the glass more durable. Generally, these additives take up no more than 26 to 30 percent of the glass mixture.
Advertisement
3
Add other chemicals, depending on the glass's intended purpose. The most common addition for decorative glass is lead oxide, which provides the sparkle in crystal glassware, as well as the softness to make it easier to cut and also lowers the melting point. Eyeglass lenses may contain lanthanum oxide because of its refractive properties, while iron helps glass absorb heat.
- Lead crystal can contain up to 33 percent lead oxide; however, the more lead oxide, the more skill required to shape the molten glass, so many lead crystal makers opt for less lead content.
As noted above, iron impurities in quartz sand make glass made with it appear greenish, so iron oxide is added to increase the greenish tint, as is copper oxide. Sulfur compounds produce a yellowish, amber, brownish or even blackish tint, depending on how much carbon or iron is also added to the mixture.
The container should be able to withstand the extremely high temperatures within the kiln - depending on your additives, your glass mixture may melt at a range of temperatures between 1,500 and 2,500 degrees Celsius. Your container should also be easily grasped with metal hooks and poles.
6
Melt the mixture into a liquid. For commercial silica glass, this is done in a gas-fired furnace, while specialty glasses may be created using an electric melter, pot furnace or kiln.
- Quartz sand without additives becomes glass at a temperature of 2,300 degrees Celsius (4,172 degrees Fahrenheit). Adding sodium carbonate (soda) reduces the temperature needed to make glass to 1,500 degrees Celsius (2,732 degrees Fahrenheit).
This means stirring the mixture to a consistent thickness and adding chemicals such as sodium sulfate, sodium chloride or antimony oxide.
8
Shape the molten glass. Shaping the glass can be done in one of several ways:
- The molten glass can be poured into a mold and let cool. This method was used by the Egyptians, and it is also how many lenses are created today.
- A large amount of molten glass can be gathered at the end of a hollow tube, which is then blown into while the tube is turned. The glass is shaped by the air entering the tube, gravity pulling on the molten glass and whatever tools the glassblower uses to work the molten glass.
- The molten glass can be poured into a bath of molten tin for support and blasted with pressurized nitrogen to shape and polish it. Glass made by this method is called float glass, and it is how glass panes have been made since the 1950s.
EXPERT TIP
Bicycle Glass
Glassblowing Experts
Bicycle Glass Co. was founded in 2016 by David Royce and Michael Boyd, two professional glass experts. Bicycle Glass is primarily a lighting company, committed to quality, sustainability, and affordability. All Bicycle Glass products are made of high-quality, recycled glass and are hand-blown by a dedicated team of artisans. The studio is committed to reducing its carbon footprint by conserving energy in all of its production. Using renewable wind energy to offset all electricity usage, the studio is actively working toward the goal of carbon neutrality. Bicycle Glass believes that high-quality, handmade glass products should be within reach for everyone.
Bicycle Glass
Glassblowing Experts
You can create a wide variety of objects by pouring molten glass into molds. This process is called glass casting; you carefully pour the molten glass from the furnace into the mold of your choice, then let it cool and anneal slowly. The most popular applications for this technique are glass sculptures and lighting fixtures with unique designs.
9
Slowly cool the glass in a kiln. This process is called annealing, and it removes any stress points that may have formed in the glass during cooling. Glass that has not been annealed is significantly weaker. Once this process is completed, the glass can then be coated, laminated or otherwise treated to improve its strength and durability.
- The precise temperature for annealing can vary based on the precise composition of the glass from as low as 750 degrees Fahrenheit to as high as 1000 degrees Fahrenheit. The rate at which the glass must cool may also change - generally, larger pieces of glass must cool more slowly than smaller pieces. Research proper annealing methods before beginning.
- A related process is tempering, in which shaped and polished glass is placed in an oven heated to at least 600 degrees Celsius (1,112 degrees Fahrenheit) and then quick-cooled ("quenched") with blasts of air at high pressure. Annealed glass breaks into shards at 6,000 pounds per square inch (psi), while tempered glass breaks into small pieces at no less than 10,000 psi and usually at around 24,000 psi.

Method 2

Method 2 of 2:

Using a Charcoal Barbecue

Download Article

1
Prepare a makeshift furnace from a charcoal barbecue grill. This method uses the heat generated by a large charcoal fire to melt silica sand into glass. The materials used are relatively cheap and common - theoretically, all you'll need is a short trip to the hardware store to be ready to make your own glass. Use a large charcoal barbecue grill - standard-size "dome" models work well. Use the thickest, sturdiest grill available. Most charcoal grills will have a vent on the bottom - open this vent.
- Even at the extremely hot temperatures reached in this method, it can be difficult to melt silica sand in a grill. Add a small quantity (about 1/3 to 1/4 of your sand's volume) of laundry soda, lime, and/or borax to your sand before you begin. These additives lower the sand's melting temperature.
- If you're going to blow your glass, have a long, hollow, metal tube handy. If you're going to pour it into a mold, prepare your mold beforehand. You want a mold that won't burn or melt from the heat of molten glass - graphite works well.
This method will push a conventional barbecue past its normal temperature limits - so hot that it's even possible to melt the grill itself. This method can cause severe injury or death if it's attempted recklessly. Proceed with caution. Have a large quantity of dirt or sand or a fire extinguisher rated for high temperatures on hand to smother the fire if needed.
3
Take every possible precaution to protect yourself and your property from the high heat. Attempt this method on a dirty or sandy surface outdoors with plenty of space. Performing this on a bare concrete surface not covered with sand or dirt could result in the concrete explosively spalling if hot molten glass is dropped onto it. Don't use any irreplaceable equipment. Stand clear of the grill while you're heating the glass. You should also wear as much of protective clothing as possible, including:
- Heavy duty oven gloves or mitts
- A welder's mask
- A heavy duty apron
- Heat-resistant clothing
4
Get a shop vacuum with a long hose attachment. Using duct tape or another method, angle its hose so that it is blowing directly into the bottom vent without touching the grill's main body. You may want to fasten the hose to one of the grill's legs or wheels. Keep the main vacuum unit as far away from the grill as possible.
- Make sure the hose is secure and will not move - if it comes loose while you're making your glass, you should not approach the grill if it's extremely hot.
- Turn the vacuum on to test your hose positioning. An accurate hose will blow directly into the vent.
5
Line the inside of your grill with charcoal. Use more charcoal than you would for grilling meat. Successful results have been achieved by filling the grill nearly to the brim.^{[1]XResearch source} Place a cast-iron pot or crucible containing your sand in the center of the grill, surrounded by charcoal.
- Hardwood (or "lump") charcoal burns hotter and quicker than briquette charcoal, making it a better choice if it's available.^{[2]XResearch source}
Light the charcoal. Consult the charcoal's packaging to know whether your charcoal can be lit directly or whether it requires lighter fluid. Allow the flames to spread evenly.
When the charcoals are grayish and emanating an orange glow, they're ready. You should be able to feel the heat from simply standing near the grill.
8
Turn the shop vac on to introduce air to the charcoal. Charcoal fed with air from the bottom can burn extremely hot (up to 2,000 degrees Fahrenheit.^{[3]XResearch source}) Beware - large flame-ups may occur.
- If you're still not able to reach high enough temperatures, experiment with replacing the lid while introducing air through the vent.
Because of the low temperature of the grill method, the molten glass may be stiffer and harder to work than glass from a kiln. Shape it with a tube, mold, or other tools as you normally would.

Expert Q&A

Search

Add New Question

Question
How do I cut glass properly?
Douglass Brown
Glassblowing Expert
Douglass Brown is a Glassblowing Expert based in Half Moon Bay, California. He has over 25 years of experience as a glass artist, and is the owner and operator of 2 glass blowing studios in the San Francisco Bay Area, Half Moon Bay Art Glass and Mare Island Art Glass. Douglass believes in sharing hot glass experiences with anyone who wants to learn about the processes of blowing and sculpting glass. When not teaching, Douglass creates glass art that is a mix of his takes on nature and functional glassware. He has also created the Glass Troubadours, which is a mobile glass blowing studio that hosts parties, events, and visits craft shows.
Douglass Brown
Glassblowing Expert
Expert Answer
To cut glass, wear safety glasses and prepare the glass surface by cleaning it. Measure and mark the cutting line with a ruler and a glass cutter. Before scoring, apply a small amount of oil to the glass cutter for smoother cutting. Apply even pressure while scoring along the marked line, then break the glass by gently applying pressure. Smooth any sharp edges with fine-grit sandpaper or a glass file. Throughout the process, prioritize safety by wearing protective gear.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 0
Question
How can I make stained glass at home?
Douglass Brown
Glassblowing Expert
Douglass Brown is a Glassblowing Expert based in Half Moon Bay, California. He has over 25 years of experience as a glass artist, and is the owner and operator of 2 glass blowing studios in the San Francisco Bay Area, Half Moon Bay Art Glass and Mare Island Art Glass. Douglass believes in sharing hot glass experiences with anyone who wants to learn about the processes of blowing and sculpting glass. When not teaching, Douglass creates glass art that is a mix of his takes on nature and functional glassware. He has also created the Glass Troubadours, which is a mobile glass blowing studio that hosts parties, events, and visits craft shows.
Douglass Brown
Glassblowing Expert
Expert Answer
To make stained glass at home, start by gathering colored glass sheets, a glass cutter, and essential tools. Design a pattern, clean the glass, and carefully cut along the marked lines. Apply copper foil to the glass edges, assemble the pieces following the pattern, and secure them by soldering. Finish the project by cleaning and adding optional touches. Finally, decide whether to display the stained glass or incorporate it into a larger project. Always adhere to safety measures when working with glass and soldering equipment.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 0
Question
Will any chemicals appear if I'm making glass?
Community Answer
It's possible if you're using regular beach sand with impurities instead of pure silica sand. If this is the case, you can use a mask and avoid standing close to the kiln while melting the glass.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 22 Helpful 85

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

Some beach sands can be used in place of pure silica sand, though the resulting glass may be opaque, discolored, or of a lesser quality. Use the whitest, finest, most-uniform sand as is available.
Thanks
Helpful0 Not Helpful0
If your sand or additives are coarse-grained, pulverize them with a mortar and pestle or a mechanical grinder. Finer-grain particles melt quicker.
Thanks
Helpful0 Not Helpful0
Ground-up pieces of old glass can be added to sand before melting to recycle it into new glass. The old glass, or "cullet," must first be checked for impurities that would weaken the new glass made with it - look for bubbles.
- When grinding glass, wear a face mask to prevent accidental inhalation.
Thanks
Helpful0 Not Helpful0

Show More Tips

Tips from our Readers

The advice in this section is based on the lived experiences of How.com.vn readers like you. If you have a helpful tip you’d like to share on How.com.vn, please submit it in the field below.

Sand from the beach can also be useful if silica sand is not available. This will normally create lower-quality glass but will still look nice and add a touch of character.
Clear any flammable items, such as leaves, if you're doing this outside.
Be careful! Safety first.

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Always use caution around high-heat sources. Never attempt to make glass around children or pets.
Thanks
Helpful0 Not Helpful0
Extinguishing extremely hot fires with water can make them worse. For instance, a fire that burns at 2,000 degree Celsius is hot enough to split water (H2O) in to its component hydrogen and oxygen atoms, releasing an enormous amount of heat energy.^{[4]XTrustworthy SourceU.S. Department of EnergyOfficial site for the U.S. Department of Energy, which provides resources related to energy safety, conservation, and efficiencyGo to source} For very hot fires, it's best to keep a large bucket of dirt or sand on hand.
- Class D fire extinguishers contain sodium chloride (table salt) and are used to smother metal fires.
Thanks
Helpful0 Not Helpful0

Things You'll Need

Silica sand (silicon dioxide)
Sodium carbonate (washing soda)
Calcium oxide (quicklime)
Other oxides and salts (e.g., magnesium oxide, aluminum oxide, iron oxide, magnesium oxide or sodium or calcium salts optional)
Lead oxide (optional)
Heat-resistant crucible, form or hollow tube
Glass kiln or furnace then the glass was over