How to Install a Privacy Fence

Fencing can be an important part of your home’s exterior design. Fencing not only adds privacy and security to your home, it also increases its value and (normally) aesthetic appeal. It provides security to children and pets. It is an asset to your property as it can give character and depth to your home. There are a wide variety of options for every budget and aesthetic taste. The following is a guide on how to install a wood privacy fence, though other options are also discussed and explained.

Part 1

Part 1 of 3:

Before Building Your Fence

Download Article

1
Check neighborhood rules. Before building a fence, it will be important to determine if you are allowed to build a fence at all. Building one in an unapproved way can get you a fine and require you to tear the whole thing down. Before building, check what your local neighborhood rules or homeowner’s association rules are regarding fences.
- If the fence will be built on a shared property line, then try talking with your neighbor to find out if they’d be willing to share the cost of the fence with you.
Cities often also have rules about building fences. You will need to check what they are before building one. Some cities require permits to build a fence of any height, some only above a certain height. Find out if you need a permit or if there are any other restrictions on your building.
Advertisement
3
Obtain a permit. If you find out that you do need a permit, get one before building. These usually cost a little money and can be obtained from your local City Hall or Planning Department.^{[1]XResearch source}
- Make sure to call the Digline at 811 before you start digging.
4
Choose your materials. It is important to decide what kind of fence you want. There are many different types of materials, all with different benefits and downsides. You will need to consider how much time you want to spend on upkeep, how much money you have to spend to build the fence, and how long the fence will need to remain in its location.^{[2]XResearch source}
- A wood fence is the most common. These last between 5-20 years, depending on the type of wood (cedar will last longer than pine, for example), and are they relatively inexpensive. Wood fences may be difficult to clean, however, if they get paint on them.
- Vinyl fences will last much longer than a wood fence, up to a lifetime if using quality vinyl. They can come in a variety of colors that should not fade over time and are easily cleaned if they get paint on them. They are, however, slightly more expensive in terms of upfront costs.
- Brick is an option if you dislike the look of wood or vinyl fences, or if you feel the need for something more sturdy. You can use actual brick or you can use concrete block. The concrete block can be further covered in cobble or plaster for a "Southwestern" look. Concrete blocks can also be turned perpendicular to each other to create planters in your wall. Any kind of masonry construction, however, will be much more expensive than the other options, although it will last longer than wood.
- Growing or green fences are a great option if your city is very restrictive about permits or permits are very expensive. They are also good if you would prefer more greenery in your yard, rather than looking at a fence. You can plant Arborvitae, an evergreen shrub which grows three feet a year, put in an iron or chain fence and train ivy on it, or grow more standard hedges like holly.^{[3]XResearch source}

Part 2

Part 2 of 3:

Set the Posts

Download Article

Using string tied to stakes, determine the perimeter of your fence and mark the corner locations, as well as measuring and marking the locations of the intermediate posts (if they are needed). The distance between posts is up to you but keep in mind the normal spacing is 8 feet (2.4 m) from center to center. Mark all locations with spray paint or stake holes.^{[4]XResearch source}
2
Dig post holes. Using a post-holer, dig holes at least ¼ to ⅓ the height of your intended fence. Make sure you follow the rules stipulated in your permit, as many cities have rule regarding hole depth. You don’t want to hit a water main!^{[5]XResearch source}
- Remember to call the Digline at 811 before you dig!^{[6]XResearch source} Water mains are usually placed at least 4 ft in the ground so in most cases a 16 to 24 inch deep posthole should be safe.
- You can use a manual digger or a motorized auger. Both can often be rented from your local hardware store.
You will want to put a few inches of gravel in the bottom of the hole, to provide drainage and ensure that the posts do not rot.^{[7]XResearch source}
4
Place posts. Use 4x4 posts at your preferred height (factoring in the depth of the hole) and place them one at a time. This may require a helping hand.
- Varying the depth of the hole to keep the height of the posts the same is much more labor intensive than digging the post hole to approximately the same depth of each hole and cutting off the top of the posts after they have set for 24 hours. It is also important to seal the tops of posts to protect them from rainwater damage.
5
Pour in quick-set concrete. Before setting the concrete, use a post level to ensure that the post is plumb and double check the height to make sure it’s what you want. Pour in the concrete, mix with water according to the manufacturer’s instructions, and continue to use the level as it sets to be sure that it stays straight.
- Alternatively, mix the quick-set concrete in a bucket or wheelbarrow and then pour it in.
- You will want to continue to use string to make sure the posts are in line with each other.
Get in all the posts before moving on. Use temporary cross bracing to hold posts in place while the concrete hardens. This will take at least 24 hours.

Part 3

Part 3 of 3:

Build the Fence

Download Article

1
Measure and cut your rails. These are the boards (we recommend 2x4s) set between the posts, in a perpendicular alignment. You will attach the main boards of the fence to these rails. They should be measured and cut to fit between the posts.
- You will probably need two or three rails, depending on the height of your fence.
Next, take a 1x4 and cut it to be the same height as the posts. Mark the spots on the board where you would like your rails to go. With that marked, nail the 1x4 flat to the end of the top and bottom (and possibly middle) rails. The rails should then be perpendicular and as a 90° turn from the 1x4 board, looking a little like a T (if viewed from the side, you should see the 1” side of the 1x4 and the 4” side of the 2x4). Do this for each end of the rail.
Fit the frame in between the posts and fasten from the inside edge into the posts using deck screws. Use rust proof hardware so the fasteners do not “bleed” over time and discolor the fence.^{[8]XResearch source}
Use slats or pickets of any width you prefer, but they should not be more than 1” thick. Nail or screw them into the rails using 2” (or similar) screws or nails, using a spacer between each board to ensure that they are even and that the space between them is slightly less than their width. Continue the entire length of the fence.^{[9]XResearch source}
Now attach the boards on the inside of the fence. These should be placed so that they cover the gaps created by the outside boards.
Add a gate. You may or may not wish to add a fence gate to provide you entrance to the yard. Follow the linked instructions for adding a gate.
With this done, you can paint or stain your fence as you wish. A decorative top can be added or shrubs planted along the baseline.

What Are Best Practices For Installing Wooden Fence Posts?

Expert Q&A

Search

Add New Question

Question
How do I install premade redwood fence panels with a lattice top?
Anthony "TC" Williams
Experienced Landscaper
Anthony "TC" Williams is a Professional Landscaper in Idaho. He is the President and Founder of Aqua Conservation Landscape & Irrigation, an Idaho Registered Landscape Business Entity. With over 21 years of landscaping experience, TC has worked on projects such as the Idaho Botanical Garden in Boise, Idaho. He is a Idaho Registered Contractor and a previously Licensed Irrigator in the State of Texas.
Anthony "TC" Williams
Experienced Landscaper
Expert Answer
Basically the same way as a picket fence, but instead of putting up one at a time you'll be installing a full section at a time.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 3
Question
Which side of the fence should be placed inside my property and which side should face my neighbor?
Community Answer
The nicer side goes toward the neighbor and the post side to your yard. It's the same with chain link: the posts are on your side of the fence if it belongs to you.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 12 Helpful 11
Question
How much cement do I use, and how deep should the hole be?
Community Answer
Use a bag and a half of cement for each post. The hole should be 3 feet deep for a 6 foot high fence.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 24 Helpful 5

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

The posts, framing, and planking boards should all be made from pressure-treated lumber or cedar.
Thanks
Helpful0 Not Helpful1
The materials to build the fencing and gates are available at most hardware and home improvement stores.
Thanks
Helpful0 Not Helpful0
Only galvanized nails should be used for pressure treated wood, coated screws, stainless steel nails, or other corrosion resistant fasteners should be used with cedar, since galvanized fasteners will discolor cedar wood.
Thanks
Helpful0 Not Helpful0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Things You'll Need

8 foot (2.44 m) long 4x4 inch (89 x 89 mm) posts (amount will vary based on the total length of fencing needed). This post material should be pressure treated for best results.
8 foot (2.44 m) long 2x4 inch (38 x 89 mm) horizontal stringers (amount will vary based on the total length of fencing needed)
Fence planking (amount will vary based on the total length of fencing needed)
Post-hole digger
Carpenter's level
Shovel
Circular saw or handsaw
Hammer or nail gun
Tape measure
Square
Wooden stakes
Metal detector
Plot plan
Nails
String