How to Install a Hampton Bay Ceiling Fan

Many of the Hampton Bay ceiling fans use a Quick-Install System and use Aero-Breeze™ Technology which can move up to 25% More Air. Here are the steps of how to install one.

Part 1

Part 1 of 5:

Install the Ceiling Fan Mounting

Download Article

^{[1]XResearch source}
Advertisement
Remove the two non-slotted screws and loosen the slotted screws. This will enable you to remove the mounting plate.
Make sure the slot openings are on top. Route the wires through the canopy and then through the ball/downrod assembly.^{[2]XResearch source}
Be careful not to jam against the wiring inside the downrod. Insert clevis pin and bend to ensure security.

Part 2

Part 2 of 5:

Install the Fan to the Outlet Box

Download Article

^{[3]XResearch source}
Slide the mounting plate over the two screws provided with the outlet box. When using close-to-ceiling mounting, it is important that the mounting plate be level. If necessary, use leveling washers (not included) between the mounting plate and the outlet box. Note that the flat side of the mounting plate is toward the outlet box.^{[4]XResearch source}
If you are using close-to-ceiling mounting, hang the fan on the hook provided by utilizing one of the holes at the outer rim of the ceiling canopy. If using standard mounting, seat

Part 3

Part 3 of 5:

Make the Electrical Connections

Download Article

If you feel you do not have enough electrical wiring knowledge or experience, have your fan installed by a licensed electrician. Follow the steps below to connect the fan to your household wiring. Use the wire connecting nuts supplied with your fan. Secure the connectors with electrical tape. Make sure there are no loose strands or connections.^{[5]XResearch source}
Connect the ground conductor of the 120v supply (this may be a bare wire or a wire with green insulation) to the green ground lead(s) of the fan. When using standard ceiling mounting, there are two green grounding leads: one from the ceiling mounting plate and one from the ball/down-rod assembly. When using Close-to-Ceiling mounting, there is only one green ground lead from the mounting plate since the ball/downrod assembly is not used.
^{[6]XResearch source}
The green and white wires are on one side of the outlet box and the black wire is on the other side.

Part 4

Part 4 of 5:

Attach the Fan Blades

Download Article

Mount the fan blades to the pre-installed blade brackets by aligning the three key-slot holes in the blade with the three posts on top of the blade bracket.^{[7]XResearch source}
Ensure the key-slot holes are properly seated on the blade bracket posts.
While still holding the blade down with both hands, firmly slide the blade away from the motor housing until the blade engages in the locking mechanism. Make sure the steel locking mechanism at the rear of the blade bracket springs upward and butts against the edge of the blade indicating a secure connection.^{[8]XResearch source}

Part 5

Part 5 of 5:

Balance the Blades

Download Article

Because natural woods vary in density, the fan may wobble even though the blades are weight matched. The following procedure should correct most fan wobble. Check after each step.
to the blade brackets with the locking mechanisms engaged.^{[9]XTrustworthy SourceEnergy StarProgram run by the U.S. Environmental Protection Agency and Department of Energy focused on educating consumers about energy efficiencyGo to source}
out of position and ensure the blade tips are even. Use the enclosed blade balancing kit if the blade wobble is still noticeable by carefully following the instructions included with the kit.^{[10]XTrustworthy SourceEnergy StarProgram run by the U.S. Environmental Protection Agency and Department of Energy focused on educating consumers about energy efficiencyGo to source}

Community Q&A

Search

Add New Question

Question
What does the blue wire connect to?
Community Answer
Blue is usually for the light kit if you have one. It connects to the red in the outlet box if you have a separate wall switch for the light. If you are only using the pull chain to activate the light, it connects to black.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 0 Helpful 4
Question
What if the chain to turn on the fan will not pull down, yet the light chain works fine?
Community Answer
It is on a separate switch, this switch may be broken or worn out. Turn off power to this fan at the breaker, remove the switch cover and examine this switch. It's possible the switch is just dry and stuck, a little 3-in-1 oil may help, or some part might need replacing. This switch is located inside the housing where the blade arms come together, the light and fan switches are both under this cover.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 1
Question
How can I connect two green wires from the fan to the ceiling wire?
Community Answer
Green wire is the safety ground. To connect to your fans junction-box with the paper-jacket wire into the metal box with a screw. If the box is plastic, just connect the two wires, green of fan to paper-jacket of feed wire w/ a wire nut.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 1