How to Install a Camper Awning

It can be difficult to find shade while using a camper. Installing an awning tends to be the quickest way to enjoy continuous protection from the sun when there is no natural shade to be found. Though you can have an awning professionally installed, it is a simple enough task that you might want to consider saving some money by doing it yourself.

Part 1

Part 1 of 3:

Placing Your Camper Awning

Most packages contain stainless steel mounting brackets, silver reflective material, and extra fiberglass poles to combat against the wind.
Though most awnings are placed on the front of the camper above the door, this is entirely up to you. You can put the awning on any wall of the camper that is long enough and thick enough. If you choose to put your awning on the backside of your camper, it will just mean that you have to walk around the camper to enjoy the shade.
Advertisement
3
Use a felt tip marker to mark where the ends of the awning will be. You can use a tape measurer to measure along your camper and find the best place for your awning. Make sure the walls of the camper are at least 1 inch (2.54 cm) thick in this area to ensure the camper is structurally strong enough to hold the weight of the awning. You can confirm this in your owner’s manual or measure the thickness of the wall in an opening such as doorway or window.^{[1]XResearch source}
- Another way to measure the wall thickness is to drill a screw all the way through and mark it on the other side of the wall. Pull the screw back out and measure from the head of the screw to the mark and that will be your wall thickness. Be wary of making extra holes in your camper, though.
It will help to have at least two helpers for this task. Have one person on either end holding either a chalk line or a straight edge of some kind. As they hold, snap the chalk line or trace a line down the straight edge.^{[2]XResearch source}
Advertisement

Part 2

Part 2 of 3:

Installing the Mounting Hardware

Use the felt tip marker to mark the hole on each bracket. This will mark where you need to drill later.^{[3]XResearch source}
Again, use your felt tip marker to make a mark for drilling. You can find the middle by measuring the distance from one point to the next and making a mark, at the halfway point. For example, if it’s ten feet from mark to mark, you would mark the five foot point as your middle.^{[4]XResearch source} You can then set the brackets aside for now.
3
Drill holes for the mounting bracket screws. Use the drill bit size recommended in the awning manufacturer’s instructions, as different awnings may require slightly different sized screws. Drill straight through the holes you previously marked.^{[5]XResearch source}
- Most of the time you will use a 3/16 drill bit for these holes.^{[6]XResearch source}
Use a sealant such as silicone. This will seal the hole around the screws and prevent water from entering your camper.^{[7]XResearch source}
Use a screwdriver and the provided screws to screw the brackets into the holes that you drilled.^{[8]XResearch source} Using a drill will over-torque the screws and make the structure weaker.^{[9]XResearch source}
Advertisement

Part 3

Part 3 of 3:

Installing the Camper Awning

You will need to slide the attachment hooks on the brackets into the awning. This will secure the awning to the brackets.^{[10]XResearch source}
Pull out the support legs until the awning canopy is positioned properly.^{[11]XResearch source}^{[12]XResearch source}
Torsion adjustments can usually be made with a knob located at the side of the awning. This will adjust how tightly the awning is stretched while extended.^{[13]XResearch source}
This part will be installed halfway down the awning and will reduce flapping. This will increase the longevity of your awning by preventing wear and tear due to flapping.^{[14]XResearch source}
As long as one end is slightly higher than the other, the awning will be pitched. This will allow any water to flow off to one side rather than be stagnant on the top of your awning.^{[15]XResearch source}
Advertisement

Community Q&A

Search

Add New Question

Question
How do I replace the right awning arm on a dometic model 9400 RV awning?
Camparama
Community Answer
There is a spring in the roller and if you inadvertently loosen it you will have more damage and a great potential for injury to yourself. Take it to your local RV specialist.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 3 Helpful 0

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

You will need to have some basic knowledge of how to use tools like a drill or screwdriver and structural knowledge about your camper. This will help the camper awning installation go smoothly.
Thanks
Helpful3 Not Helpful0
A watertight seal can be created by spraying silicone around the screw holes
Thanks
Helpful1 Not Helpful0
If the camper awning instructions that came with the awning you purchased differ from these instructions, always assume the manufacturer's instructions are best and follow them instead.
Thanks
Helpful0 Not Helpful1

Show More Tips

Warnings

Do not use a power screwdriver to attach the screws. This will over-torque them and make the awning structure weaker.
Thanks
Helpful3 Not Helpful1
If you find that your camper's walls are too thin to support the awning structure, use the provided backing plate or a .25-inch (0.6 cm) thick steel plate and drill holes with a carbide bit drill. You can also use bolts instead of screws to make the awning more secure.^{[16]XResearch source}
Thanks
Helpful1 Not Helpful0