How to Hook Up a Trailer

Hooking up a trailer to your car or truck is an easy way to increase the storage capacity of your vehicle. However, failing to attach your trailer correctly can lead to damage to your own car, the trailer, and other vehicles around you as you drive. By securing the coupler to the hitch ball on your vehicle, making sure that it’s locked in properly, and wiring up the lights, you can hook up a trailer safely and easily.

Get Car Support Solve Any Problem

Hi there! Do you have a question about how to diagnose or fix a problem with your car? I’ve read the manual so you don’t have to. Select your make, model, and year, then ask away!

*

Part 1

Part 1 of 3:

Lining up Your Vehicle

Download Article

1
Move the trailer to a long, easily accessible area. While it’s possible to reverse towards a trailer on an angle or around corners, it’s much easier to attach your trailer if you approach it in a straight line. If you can, wheel the trailer to a long stretch of a driveway or a parking lot where you’ll have plenty of room to work.^{[1]XResearch source}
- Most trailers will have an attached jack with a wheel on the end that can help keep the trailer level without it being attached to anything. Keep this out while moving the trailer by hand to reduce some of the heavy lifting.
- If your trailer is already full, it might be more difficult to move by hand. Rotate it on the spot as much as you can to make the reversing job easier, as trying to move it yourself may be difficult.
2
Reverse your vehicle in a straight line with the trailer. Drive your vehicle forward so that it is directly in front of the trailer. Slowly reverse the car, turning the wheel slightly to keep it as directly in line with the trailer as you can. Stop when the back of the car is around 1 foot (0.30 m) away from the front of the trailer.^{[2]XResearch source}
- Reversing your car into the right position and space is much easier when you have a lot of room to work with.
- Keeping the trailer and vehicle lined up properly will make driving much easier, especially when you’re first getting onto the road.
- It might help to get a friend or someone else to help you reverse the car. They can guide you on how far back to drive and help you correct the vehicle if it starts angling in one direction.
Advertisement
3
Position the trailer coupler slightly above the hitch ball. The trailer coupler is the metal socket on the end of the trailer that will connect to the back of your car. Rotate the handle on the trailer jack to raise or lower the coupler so that it’s 2 to 3 inches (5.1 to 7.6 cm) above the hitch ball on the back of your car.^{[3]XResearch source}
- If your trailer doesn’t have an attached jack, you could use a regular car jack to hold the trailer at the right height.
- Attached trailer jacks will be slightly behind the coupler on the trailer.
- If the trailer is light enough and easy to move, you could simply lift the trailer coupler forward and place it over the hitch ball.
- The hitch ball is the metal ball on the back of your car that the trailer coupler will attach to.
4
Back your vehicle up until the coupler is directly above the hitch ball. With the coupler raised a little above the hitch ball, get back into your vehicle and reverse backward a little further. Get a friend to help guide you to reverse your car so that the hitch ball and coupler are perfectly lined up.^{[4]XResearch source}
- It’s possible to reverse into position by yourself, but it will take a lot of trial and error. Reverse a little bit, put on the break, and get out to check how much further back you need to go. Repeat this process until everything is lined up.
- If you reverse too far back, you may hit the coupler and scratch or damage the back of your car.

Part 2

Part 2 of 3:

Securing the Trailer

Download Article

1
Unlock the trailer coupler latch. The latch on top of the trailer coupler is the first mechanism that will keep your trailer locked onto the back of your car. Remove the latch pin from the trailer coupler and lift the latch upwards to unlock it. This will allow it to sit on the hitch ball on your vehicle.^{[5]XResearch source}
- Some trailers might have methods other than latch pins used to hold the latch in place. Try to raise the latch and see what’s holding it in place to find the right way to release it.
- The latch will likely be a metal handle on top of the trailer coupler.
- If the coupler is already unlocked, you can skip this step.
2
Lower the coupler socket onto the vehicles hitch ball. Check the hitch ball on the back of your vehicle and remove any covers or protectors sitting on top of it. Use the handle attached to the trailer jack to lower the coupler socket onto the hitch ball, until the weight of the trailer is supported entirely by the ball.^{[6]XResearch source}
- If the latch has been lifted and everything is positioned properly, the socket should lower and sit perfectly on the hitch ball.
3
Move the trailer jack out of the way. The trailer jack is great for positioning the trailer properly but will get easily damaged if you drive with it attached. Look for a latch or latch pin on the trailer jack to rotate it up into the trailer and hold it out of the way while you drive. Alternately, you may be able to detach the jack entirely and keep it in your vehicle until it’s needed.^{[7]XResearch source}
- The wheel on the trailer jack is not designed for use while driving. Do not drive with the trailer jack on or extended at risk of damaging the trailer, your vehicle, or other vehicles on the road.
4
Lock the coupler latch and insert the latch pin. With the coupler sitting securely on the hitch ball, reverse the process of unlocking the coupler latch to lock it in place. Push the handle on the coupler down so that it is parallel to the ground. Insert the latch pin to hold it in place and prevent the coupler from unlocking while you drive.^{[8]XResearch source}
- Different trailers and trailer couplers may have slightly different locking mechanisms. Always consult the owner’s manual for your own trailer to make sure you lock it into place properly.
5
Attach the safety chains to the back of your vehicle in a cross pattern. Run one of the safety chains below the coupler and hitch ball and attach it to the opposite side of the hitch ball. Repeat with the other chain to create an overlapping cross underneath the coupler and hitch ball.^{[9]XResearch source}
- The safety chains will be the last safety mechanism in place if the coupler latch fails, so they are legally required in many places.
- If the coupler disconnects from the vehicle while you’re driving, it will fall and land on the crossed chains rather than hitting the road.
- The safety chains will be attached to your trailer, just below the coupler.

Part 3

Part 3 of 3:

Connecting the Lights

Download Article

1
Locate the wiring socket on the back of your vehicle. The wiring socket is a wide plug that will power the lights on your trailer. Look for a small panel on the back of your vehicle, inside the trunk, or even a loose wire close to the hitch ball. Make sure it isn’t damaged and is free from any corrosion that may prevent it from working properly.^{[10]XResearch source}
- If you cannot find the wiring socket on your car, check the manufacturer’s instructions for your car for further assistance.
- If your wiring socket is damaged, corroded, or frayed in any way, have it looked over by a mechanic before plugging the trailer wire into it.
2
Plug the trailer wire into your vehicle. There should be a loose wire with a plug on one end near the trailer coupler. Run the wire above the coupler and the hitch ball and plug it into the socket on the back of your vehicle. Press the plug securely into the socket and use any latches on the wire to hold them together.^{[11]XResearch source}
- Some trailers will have metal loops along the side of the coupler that the wire can be threaded through to keep it out of the way.
- Avoid running the wire underneath the coupler and hitch ball, as this will increase the chances of it getting damaged or becoming unplugged should the trailer detach from your vehicle.
3
Test the headlights, blinkers, and brake lights on the trailer. Before you start driving, you should always make sure the trailer lights are working. Start your vehicle, engage the handbrake, and turn on the headlights. Check the appropriate lights on the back of the trailer are on, before repeating the same process with each indicator and the brake lights.^{[12]XResearch source}
- If any of the lights aren’t working, you should not drive the trailer. This is the same as driving without the corresponding light on your car working. Call a mechanic to ask for assistance before driving your car with the trailer attached.
- Rather than moving back and forth from the driver's seat of your car to the rear end of your trailer, ask a friend to check the lights while you activate them.

Community Q&A

Search

Add New Question

Question
I want to place my Airstream in a place where the tow vehicle would be at a slight angle to the trailer when unhitching/hitching. Is it possible to approach for hookup at an angle, instead of truck and trailer being in a straight line?
Community Answer
Yes. A little more difficult to line up, but you can technically hook up while at a 90-degree angle to the trailer.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 1 Helpful 8
Question
Can I put the safety cable over the ball and then attach the coupler?
Community Answer
No, if the safety chains are too long, shorten them to the necessary length.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 9 Helpful 10
Question
How do I wire a 7-blade trailer connector to a 2011 Ford transit?
Community Answer
Your 2011 Transit is not capable of towing a trailer requiring 7 pins. Transit Vans are generally not able to tow any type of trailer, let alone one requiring electric brakes (7-pin). Ford does not recommend installing a trailer hitch on their transit vans for this reason. It may also void your warranty by installing a hitch on this van.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 7 Helpful 5

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

If the trailer is light enough, it may be easier to wheel it to the hitch ball on your car, rather than reversing the car to the trailer. Always lift with your legs to avoid injury while you do so.
Thanks
Helpful0 Not Helpful0
If your car has a reversing camera, you may be able to use it to easily line up the trailer socket with the hitch ball.
Thanks
Helpful0 Not Helpful0
You should check to make sure the hitch ball and coupler are firmly attached. Use the jack to lift up the trailer slightly and make sure it stays securely attached to your car.
Thanks
Helpful0 Not Helpful0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Always check to make sure that a child or pet has not wandered behind the vehicle before you start backing up.
Thanks
Helpful4 Not Helpful1
The safety chains should only be used as an extra measure of security, rather than being relied on to move your trailer.
Thanks
Helpful2 Not Helpful0
Always inspect the hitch connections, tires and running gear before you get ready to pull away after a rest or fuel stop.
Thanks
Helpful5 Not Helpful5
Make sure the ball hitch on your vehicle is the same size as the ball socket on your trailer. The size of each will be stamped near the ball or socket.^{[13]XResearch source}
Thanks
Helpful0 Not Helpful0
Never have a person stand between the vehicle and trailer while you move the trailer.
Thanks
Helpful0 Not Helpful0