Download ArticleDownload ArticleThis article was co-authored by Himesh Patel and by How.com.vn staff writer, Hunter Rising. Himesh Patel is a Metallurgical Engineer at Mcclelland Laboratories in Reno, Nevada. With over five years of industry and graduate research experience in the raw materials industry, Himesh has extensive knowledge of mining and mineral extraction and recovery methods, mine financing, and the environmental impacts of mining. He received his MS in Metallurgical Engineering from the University of Nevada, Reno, and a Dual Degree in Mineral Engineering from the Indian Institute of Technology (Indian School of Mines), Dhanbad. Himesh is passionate about educating the public about the minerals industry.
There are 10 references cited in this article, which can be found at the bottom of the page.
How.com.vn marks an article as reader-approved once it receives enough positive feedback. This article received 28 testimonials and 90% of readers who voted found it helpful, earning it our reader-approved status.
This article has been viewed 1,002,745 times.
Steel is a common durable alloy, and while most steel used in tools is already tough, you can harden it even more to prevent wear and tear. Hardened steel prevents knife blades from dulling and tools from bending and breaking. With a simple heating and quenching process, you can make your steel last for much longer!
Steps
Light a propane blow torch to use as a heat source. Open the gas valve near the base of the torch. Hold a striker over the end of the torch and squeeze it to create a spark. The torch should ignite after a few tries. Turn the gas valve to adjust the flame to a small cone shape.[1]- Larger flames produce less heat while smaller flames produce a higher heat.
- Blow torches only heat a small concentrated area. For larger pieces of steel, you need to use a forge in order to heat the whole thing.
Safety Precautions
Always wear goggles and gloves when operating a propane blow torch.
Before operating your torch, read all instructions so you know how to handle it safely.
Hold the steel directly in the flame. Hold the steel with your non-dominant hand using a pair of metal tongs so you aren’t near the flame. If you can’t hold the steel with tongs, set it on a larger fireproof work surface. Use the torch with your dominant hand to heat the entire steel piece before focusing the flame on the area you want hardened, such as the end of a screwdriver or chisel.[2]- Wear thick gloves so you don’t burn yourself.
- Work on a metal or steel surface, such as an anvil, to avoid any fire hazards.
Advertisement
Wait until the steel turns cherry-red in color. Watch for the color of the steel to change as it gets hotter. When the steel is a bright cherry-red, about 1,400 °F (760 °C), then it’s been heated enough to strengthen the steel.[3]- The actual temperature of the steel depends on the carbon content inside. Higher carbon contents will take longer to heat.
- Another good test for determining when the steel is ready is seeing if a magnet sticks to its surface. If the magnet doesn’t stick, it’s ready to be pulled away from the heat.[4]
- Fill a heat-safe container with water or oil deep enough to submerge your steel. Use a coffee can or similarly shaped container as your quenching chamber. Pour in water or vegetable oil so it’s 2–3 inches (5.1–7.6 cm) from the rim of the container. Make sure the oil or water is at room temperature.
- This step should be done before heating the steel, as the steel should be quenched immediately after removing from heat.[5]
- Water is great for rapidly quenching the hot metal, but it could cause thin steel to distort or crack.
- Vegetable oil has a higher boiling point, so the hot steel will take longer to cool and reduce the chance of it cracking. However, oil may spill and create a fire hazard if the steel is put into the oil too quickly.
- This step should be done before heating the steel, as the steel should be quenched immediately after removing from heat.[5]
- Transfer the heated steel directly to your quenching medium. Use your tongs to carry the steel while it’s still hot to your container. Stand back as you completely submerge the steel in the water or oil since it will create steam or splash out. Keep holding onto the steel so you don’t have to fish it out later.[6]
- Quenching the steel rapidly cools it so the alloys inside harden together.
- Wear thick gloves and a face mask before you quench your steel so the water or oil doesn’t splash onto your hands.
- Keep a grade B fire extinguisher nearby in case of a fire.
Remove the steel from the quenching medium when it stops bubbling. The water or oil will continue to boil as the heat transfers from the steel. Keep the steel completely submerged until there is no more steam or bubbles, which should only take a few minutes. Set the steel back on your work surface when you’re finished.[7]Quenched steel is harder, but it becomes more brittle. Don’t drop or try to bend the steel once it’s removed.
- Wipe any residual quenching medium off the steel. Water is corrosive to steel and could cause damage if it’s left on the surface. Wear gloves while you use a shop cloth to dry the steel completely.[8]
Preheat your oven to 375 °F (191 °C). Let the oven heat completely before you place your steel inside. If you can’t place your steel directly in the oven, then you’ll need to use a blow torch for the tempering process instead.[9]- Use a smaller toaster oven if your piece of steel fits inside. That way, you can still use your oven for the rest of the evening.
Put your steel inside the oven for 3 hours. Set your steel directly on the oven rack or on a baking sheet. Let your oven heat the piece of steel. During the tempering process, the steel heats up enough to soften the alloys inside to make it less brittle.[10][11]If you need to use a blow torch, focus the flame tip on the area you want hardened. Keep heating the steel until you notice a blue color form on the metal. This signifies that the steel is tempered.
Turn off the oven and let the steel cool inside it overnight. Once the steel’s been heated for 3 hours, let the steel cool slowly. This allows the steel to normalize and keep its hardened structure. Take the steel out of the oven the following morning.[12]- If you tempered the steel with a blow torch, set the metal on an anvil or another large steel surface to conduct the heat.[13]
Community Q&A
- QuestionI heat treated a piece of carbon steel to make it less likely to wear (using its edge as a cutting surface in a wood turning application). I now want to reverse the process so I can drill and tap the metal tip. How do I do this?
Community AnswerHeat the area you'd like to drill just until it starts to glow red, then allow it to cool slowly. This answer was tested with a utility knife blade and it drilled through with ease. - QuestionHow do I harden a steel hammer so that is lasts longer and is more durable?
Community AnswerThis is not advisable. Hardening will cause it to be more brittle, which could cause the hammer to chip and cause injury. - QuestionCan a softly tempered piece be re-tempered harder without going through the hardening procedure again?Community AnswerNo. The tempering reduces the amount of martensite and thus makes the steel softer. Heating it again to a lower temperature will not introduce additional martensite. The only way to do that is to heat it until the metal de-magnetises, quench it again, and then temper to the desired hardness.
Video
Tips
Warnings
- Keep a fire extinguisher near your workstation in case of a fire.Thanks
- Wear safety glasses and gloves while working with hot metal.Thanks
- Don’t touch the metal with your bare hands since it could cause severe burns.Thanks
Things You’ll Need
- Blow torch
- Striker
- Steel
- Metal tongs
- Safety glasses
- Work gloves
- Heat-safe container
- Vegetable oil or water
- Shop cloth
- Oven
References
- ↑ https://youtu.be/JQMHwthAlrM?t=59s
- ↑ https://youtu.be/L_xc_D0VQBk?t=3m33s
- ↑ https://youtu.be/L_xc_D0VQBk?t=3m11s
- ↑ https://youtu.be/bdRtg6xxkrk?t=2m26s
- ↑ https://mgs.edu/making-chisels-skips-newsletter/
- ↑ https://youtu.be/LPVxVpdNWKs?t=5m27s
- ↑ https://youtu.be/bdRtg6xxkrk?t=2m55s
- ↑ http://www.technologystudent.com/equip1/heat1.htm
- ↑ https://youtu.be/bdRtg6xxkrk?t=3m12s
About This Article
To harden steel, start by heating the metal directly with a blow torch until it turns a cherry red color. Then, use a pair of tongs to carry the steel to a container filled with water or vegetable, and submerge the hot metal in the liquid. When the liquid stops bubbling, remove the metal from the container and wipe off any excess liquid. To temper the steel so it isn't brittle, place it in an oven heated to 375 °F for 3 hours, and then it let it cool overnight. For more information on using a blowtorch and protecting the steel, scroll down!
Reader Success Stories
"I am nearly 16 and can not wait until I have my drivers license. I have in the past few years became more and more fascinated with blacksmithing, but have not had an income to even get it started. I am simply trying to learn anything and everything that there is to know about it. This is a great source that you can learn lots of information from and I'll advise it to to a handfuls of others. Very helpful!"..." more
Did this article help you?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
