How to Fix a Kitchen Faucet

Fixing a kitchen faucet is a DIY project that is usually easier and less time-consuming than you imagine. Leaks are handled either by treating blockages with vinegar or replacing some of the faucet’s smaller parts. The parts most likely to need replacing depend on the type of faucet you own. Keep track of the pieces as you work and reassemble them later to have a faucet that works as good as new.

Method 1

Method 1 of 5:

Setting up for Repair Work

Download Article

Before you begin, inspect the faucet to figure out where the leak is. Leaks almost always emanate from either the faucet’s base or the spout. Knowing where the leak is will help you determine what parts are responsible for the leak.^{[1]XResearch source}
Turn the faucet’s water supply off. Look under your sink first. You may see a pair of valves you can turn clockwise to stop water from flowing into the faucet. If the valves aren’t there, turn off the main water line.^{[2]XExpert SourceAllen Lee
Home Improvement SpecialistExpert Interview. 10 July 2020.} It is usually indoors, in the basement, next to the water meter.^{[3]XResearch source}
Advertisement
Before taking apart the faucet, check to see that the water supply has been turned off. Let the water flow out of the faucet until it stops. Any built-up pressure will also drain away.^{[4]XResearch source}
It’s no fun to drop a small but important piece down the sink. To save yourself additional work, place the sink’s strainer baskets over the drain. If you don’t have strainers, cover the drains with rags or towels.^{[5]XResearch source}
After fixing the faucet, you will have to return the parts in the proper order. To remember this order, keep a camera nearby to record your work. Also, keep the parts separated and ordered so you know when you need each piece.
6
Pour some vinegar into a container to clean faucet parts. You will most likely notice mineral buildup on some of the parts. Soak the parts in vinegar for a couple of minutes first to soften the buildup, then scrub them off with a microfiber cloth or a nylon abrasive pad.^{[6]XResearch source}
- A screwdriver can also be helpful for scraping away debris inside the faucet’s parts.

Method 2

Method 2 of 5:

Fixing a Ball Faucet

Download Article

Lift the handle and look for a small hole underneath it, near the faucet's stem. Use the Allen wrench to turn the screw counterclockwise until you can lift the handle off of the faucet.^{[7]XResearch source}
2
Tighten the adjusting ring to fix leaks in the handle’s base. Grip the top of the metal cap with a spanner tool. Turn the cap clockwise to tighten the white, plastic ring inside of it. If your leak was at the handle’s base, this may be enough to repair it. Replace the handle and turn on the water to test it.^{[8]XResearch source}
- A spanner tool is typically included in the repair kits available for this type of faucet. Otherwise, visit a home improvement store.
Using a pair of slip-joint pliers, grip the top end of the metal cap. Rotate it counterclockwise to loosen it. Set aside the cap, then remove the 2 plastic rings inside the faucet to expose the ball.
Pick up the ball and look it over to make sure it isn’t worn or cracked. If it is, replace it with a new ball purchased from a hardware store or taken from a repair kit.^{[9]XResearch source}
Put the head of screwdriver through the rings and springs to help lift them out of the faucet. Place the new springs in the holes in the faucet, then drop new rubber seats on top of them. Press them down with your finger to set them in place.
Place the metal ball on the rubber pieces, matching the ball’s groove to the one in the faucet. Put the 2 plastic rings back in place next. Then put the metal cap back in place and tighten it with pliers. Finally, screw the handle back onto the faucet with the Allen wrench.^{[10]XResearch source}

Method 3

Method 3 of 5:

Repairing a Cartridge Faucet

Download Article

The cap will be on top of the faucet handle. Hold the knife flat and stick the blade under the cap. Gently lift it up to expose the Allen screw.
Turn the screw counterclockwise to loosen the handle. Lift it off the stem and set it aside.
Underneath the handle, you will see a metal cap. Twist it counterclockwise by hand to remove it. If it’s stuck in place, use pliers to unscrew it.
Hold the screwdriver vertically and lower the tip into the metal adapter. The screw is on the bottom. Twist it counterclockwise to remove it, then set aside the metal adapter as well as the plastic piece underneath it.^{[11]XResearch source}
You should see the top end of the cartridge now, most likely copper-colored. Grip the black, plastic piece around it with pliers. Turn it counterclockwise until it’s loose enough to lift off the faucet.^{[12]XResearch source}
The clip is the copper-colored, horseshoe-shaped piece of metal. Use a screwdriver to lift it up so that you can grab onto it with the pliers. Pull it horizontally, away from the cartridge, to remove it.^{[13]XResearch source}
7
Twist the cartridge with pliers to remove it. Replacement cartridges come with a plastic cap that you need to place on top of the old cartridge first. Use your pliers to twist the cartridge back and forth as much as possible until it’s loose enough to be removed. Cartridges can be pretty tough, so expect to have to apply some force.^{[14]XResearch source}
- If the cartridge is still stuck, find a cartridge-removing tool at the hardware store.
8
Place the new cartridge in the faucet. Hold the top end of the cartridge with your pliers. Lower the cartridge into the faucet, then twist it so the notch on top faces you. Replace the brass clip, followed by the remaining parts. Then test the faucet.^{[15]XResearch source}
- If the hot and cold water flows are reversed, turn the cartridge around.
- To ensure that the faucet lasts longer, replace any worn or damaged parts. Take them to the home improvement or hardware store to get the correct replacement.

Method 4

Method 4 of 5:

Fixing a Ceramic Disc Faucet

Download Article

On ceramic disc faucets, the screw cover is near the bottom of the handle. Lift the handle up and you will see it. Slip the end of a knife behind it and gently pry it off.
Stick the Allen wrench into the hole under the screw cover. Turn the screw counterclockwise to loosen and remove the handle.
Underneath the handle, you will find a metal cap. Wrap the pliers around the top end and twist the cap counterclockwise to remove it.^{[16]XResearch source}
Next, you will see the disc cartridge plastic cover. Look for 3 holes around the outside edge. Use a Phillips screwdriver to turn the screws counterclockwise and remove them. Lift the disc cartridge out of the faucet afterwards.^{[17]XResearch source}
5
Replace the rubber seals in the cartridge. Flip over the cartridge to find the rubber seals. They may look worn or broken. Bring the rings into a home improvement or hardware store to find replacements, then insert them into the holes under the cartridge.^{[18]XResearch source}
- If the rubber seals are dirty but not broken, try scrubbing them with a microfiber cloth or soaking them in vinegar to clean them.
- Ceramic disc faucets are designed to last a long time, so they usually come with a long warranty. Check your owner’s manual, if you have it, and you may be able to get the faucet repaired at no cost.
The last part in the faucet is a plastic ring. Use a screwdriver to lift it and find the rings underneath it. Replace the rings if they look damaged by fitting new ones into the disc’s holes.^{[19]XResearch source}
Check the holes in the faucet’s base for any signs of mineral buildup. Dampen a microfiber cloth with vinegar, then scrub the holes to clean them.^{[20]XResearch source}
8
Reassemble the faucet. This shouldn’t be too difficult if you remember the correct order for the pieces. Replace the plastic disc first, followed by the cartridge, the cap, and then the handle. Remember to screw the cartridge and handle in place.
- If the faucet still leaks, the cartridge may be cracked. Take it to the hardware store to order a replacement. Remember to check your warranty to avoid paying for this expensive part.

Method 5

Method 5 of 5:

Repairing a Spout Faucet

Download Article

Spout faucets don’t have screws. The handle fits loosely over the faucet’s stem, so it’s very easy to remove by hand. Twist it back and forth to pull it off.^{[21]XResearch source}
The o-rings are the black bands over the outside of the spout. Slip the head of a screwdriver under them to help lift them off the faucet. Bring them to a plumber’s supply store or hardware store to find new ones.^{[22]XResearch source}
Also purchase a small container of plumber’s grease from the store. Coat the o-rings in the grease, then slide them over the faucet. Fit them into the faucet’s grooves. Replace the handle and test the faucet.^{[23]XResearch source}
4
Clean the diverter valve with vinegar. The diverter valve is the small plastic piece on the front of the faucet. Remove the handle to find it, then pull on it. It should come out without much of a fight. Soak it in vinegar and scrub it with a nylon cloth to clean it.^{[24]XResearch source}
- If the valve still doesn’t work or won’t come out, it may be clogged. Get help from the manufacturer.

Expert Q&A

Search

Add New Question

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Tips

To figure out what kind of faucet you have, read the owner’s manual or look at the parts inside the faucet.
Thanks
Helpful0 Not Helpful0
Take the faucet’s old parts with you to order exact replacements at the store.
Thanks
Helpful0 Not Helpful0