X
How.com.vn is a “wiki,” similar to Wikipedia, which means that many of our articles are co-written by multiple authors. To create this article, 20 people, some anonymous, worked to edit and improve it over time.
This article has been viewed 136,297 times.
Have you ever wanted to make a circuit board at home? Now you can, for use in all types of homemade electronic components.
Steps
Put on the goggles and gloves (non-optional!). Always remember safety first. You can easily blind yourself!
Make sure the area is well ventilated before mixing. The chemicals will produce hazardous fumes. You can lose your sense of smell!Advertisement
Use a non-metallic basin. Check if it can withstand the acid using a few drops.
Gently pour one part hydrochloric acid into every two parts hydrogen peroxide (add acid to water). When mixed, they form a substance that is a severe skin irritant, and will produce toxic chlorine gas.
Make enough of the solution to completely submerge the circuit board.
Gently put in the circuit board and agitate it for about ten to fifteen minutes. The solution will get warmer and fume more. Don't put your face over it!
Continue stirring until all copper has dissolved, and the solution has taken on a slight green tinge.
For cleanup, make sure you are wearing gloves. Wash the board off in cold water to remove any etching solution. Then use a paper towel or rag to dry it off completely. Set it aside. Assure that there is no solution in the workspace or containers then remove the gloves and goggles.
Mix a one to one ratio of acetone and rubbing alcohol. Take a paper towel, dip it into the solution, and gently rub it over the surface of the board. The permanent marker will begin to come off. Continue rubbing until all the marker is gone. You should see that your circuit is now inscribed in the copper.
The etching solution is toxic to fish and other water organisms. Don't pour it in the sink when you are done. It is illegal to do so and might damage your pipes.- You can reuse the solution by adding a bit of Hydrogen Peroxide right before the next etch and a bit of acid when the solutions stops working (every 4 or 5 etches). Store the solution in a completely new and different container and not pour it back into the hydrogen peroxide or HCL container.
- If you have to dispose of it label it and give it to chemical waste facility.
- You can also fell out the copper (video) and then safely pour the remaining liquid in the sink.
Advertisement
Expert Q&A
Ask a Question
200 characters left
Include your email address to get a message when this question is answered.
SubmitAdvertisement
Things You'll Need
- A non-metallic basin that is deep enough to submerge the circuit board
- Goggles
- Vinyl or Latex gloves
- A non-metallic device used to agitate the circuit board (a stick)
- Hydrochloric Acid ca. 30% (Muriatic Acid)
- Hydrogen Peroxide 3% (rest is distilled water)
- Rubbing alcohol
- Acetone or mineral spirits
Video
Tips
- Remember that the circuit board can take up to twenty minutes to etch without agitation, but as little as seven with agitationThanks
- Muriatic (hydrochloric) acid can usually be acquired at a hardware store or pool store.Thanks
- Do not look directly over your etching basin, or you will inhale toxic gas.Thanks
Advertisement
Warnings
- The hydrochloric acid you are using is concentrated (12 molar), take care not to spill any on your skin, as it will cause SEVERE chemical burns.Thanks
- Copper dust is toxic, wear a dust mask to prevent inhalation.Thanks
- The etching solution is very dangerous, so always wear your gloves and goggles, and always work in an open area.Thanks
Advertisement
Is this article up to date?
⚠️ Disclaimer:
Content from Wiki How English language website. Text is available under the Creative Commons Attribution-Share Alike License; additional terms may apply.
Wiki How does not encourage the violation of any laws, and cannot be responsible for any violations of such laws, should you link to this domain, or use, reproduce, or republish the information contained herein.
- - A few of these subjects are frequently censored by educational, governmental, corporate, parental and other filtering schemes.
- - Some articles may contain names, images, artworks or descriptions of events that some cultures restrict access to
- - Please note: Wiki How does not give you opinion about the law, or advice about medical. If you need specific advice (for example, medical, legal, financial or risk management), please seek a professional who is licensed or knowledgeable in that area.
- - Readers should not judge the importance of topics based on their coverage on Wiki How, nor think a topic is important just because it is the subject of a Wiki article.
Advertisement
