How to Drill Into Concrete

Drilling a hole in concrete is a useful and handy technique. You can put up shelves, hang paintings, install lights, and do much more quickly and safely. The process itself is simple, but selecting the right tools and understanding how to use them will save you a huge amount of time.

Part 1

Part 1 of 2:

Setting Up

Download Article

1
Buy or rent a good hammer drill. If you're just drilling one or two holes for a small project, a regular drill is fine. However, drilling concrete is much easier with a hammer drill, or a rotary hammer for large jobs.^{[1]XResearch source} These tools fracture the concrete through rapid hammering, then drill to scoop out the broken material. A normal rotary drill makes the job much slower and more difficult, since concrete is not easily shaved away in layers the same way wood and metal are. Pay extra for a hammer drill rental for any job larger than a few holes drilled through cosmetic (non-structural) concrete, such as the softer mix found in modern countertops.^{[2]XResearch source}
- It's usually worth it to pay more for a more powerful hammer drill (at least 7 to 10 amps) from a well-known brand.^{[3]XResearch source} Other beneficial features include a speed setting, depth stop, comfortable grip, and a second handle for your other hand.
2
Get to know your tool. Read the user's manual and learn what all the knobs and controls are for. Make sure you are comfortable with your tool before moving on to the next step.
- Follow all safety instructions. This includes wearing safety goggles to protect your eyes from chips of concrete, hearing protection, and heavy gloves to protect your hands from abrasion and hot drill bits. A respirator is also recommended for larger projects that create a lot of dust.
- Hammer drills can be switched to a non-hammering drill setting simply by turning the collar.
Advertisement
3
Insert a high quality masonry drill bit. Carbide-tipped masonry bits intended for hammer drills (or labeled "rotary/percussive") are designed to withstand the force of hammering and drilling dense concrete. The flutes of the drill bit must be at least as long as the hole you plan to drill, since they are important for evacuating dust out of the hole.^{[4]XResearch source}
- Rotary hammers require specialty drill bits, called SDS or SDS-MAX (for holes up 5/8" in diameter) or Spline-Shank (for holes 3/4" or larger).^{[5]XResearch source}
- Reinforced concrete is much more difficult to drill if you need to drill deeper than the steel rebar. Switch to a special rebar-cutting bit once the drill hits metal.^{[6]XResearch source} Slow down and pause occasionally to prevent overheating.
4
Set the depth. Some drills have a depth setting or depth control bar. Read the user manual and learn how to use it. If your machine does not have depth control, measure and mark the required depth on the drill bit with a pencil or masking tape. If you're not sure how deep to drill, follow these guidelines:^{[7]XResearch source}
- Because concrete is a hard, dense material, screws embedded 1 inch (2.5 cm) deep are sufficient for hanging light-weight objects. Heavier-duty projects require longer screws or concrete anchors, which should list the minimum embedment on the packaging.
- Add an additional ½" (6 mm) to the embedment to allow room for the dust that accumulates during drilling.^{[8]XResearch source} You can reduce this length if you plan to remove the dust afterward (described below).^{[9]XResearch source}
- For hollow concrete blocks or thin concrete surfaces, check the fastener specifications. Some plastic anchors require a solid backing, and will fall out if you drill through the other side.
Hold the drill with one hand like a gun, with your index finger on the "trigger". If the drill has a handle for your other hand to hold, use it. Otherwise put your other hand at the back of the drill.
EXPERT TIP
Gerber Ortiz-Vega
Masonry Specialist
Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. He earned a BA in Marketing from the University of Mary Washington in 2017.
Gerber Ortiz-Vega
Masonry Specialist
Expert Warning: Put on the appropriate safety gear, including glasses, a ventilator mask, safety glasses, gloves, and heavy pants. Also, cover any nearby doors or windows with plywood, and move any vehicles out of the area.

Part 2

Part 2 of 2:

Drilling Concrete

Download Article

Mark the point on the wall where you want to drill using a soft pencil with a small dot or cross.
2
Drill a pilot hole. Place your drill on the mark and drill briefly, using a low speed (if your machine has speed control) or in short bursts (if it doesn't). Make a shallow hole (⅛ to ¼ inches / 3 to 6 mm) to help guide your drill for the real hole.^{[10]XResearch source}
- If the project requires a large diameter drill bit, consider using a smaller drill bit for the pilot hole. This will increase the drill's stability.^{[11]XResearch source}
3
Continue drilling with more power. Turn on the hammer function if your drill has one. Place the drill in the pilot hole, keeping it exactly perpendicular to the concrete surface. Start drilling with firm, but not forceful, pressure to push the drill forward. Gradually increase the drill speed and force if necessary, but make sure the drill is stable and under your control at all times. Concrete is not a homogenous material, and the drill bit can easily skate if it hits an air pocket or pebble.^{[12]XResearch source}
- Apply enough pressure to hold the drill in place, but do not force it forward (this increases wear on the bit and can even break it). You will learn the right amount of pressure from practice.
4
Pull the drill out periodically. Bring the drill back slightly and press it back in again every ten or twenty seconds. This helps pull dust out of the hole.^{[13]XResearch source}
- Occasionally stop the drill and pull it out to let it cool for a few seconds. This is especially important for ordinary rotary drills, since they can easily overheat during a lengthy drilling process.
- You may feel a little bit of recoil and kick from the drill.
5
Break through obstructions with a masonry nail. Sometimes, a drill does not go as expected. If you hit an especially hard piece of concrete, insert a masonry nail into the hole and hammer it in to break up the concrete. Take care not to drive the nail too deep to easily remove. Insert your drill back and continue drilling.^{[14]XResearch source}
- If you see sparks or see metal, you have hit rebar. Stop drilling immediately and switch to a rebar-cutting drill bit until you are past the obstruction.
6
Blow out the dust. Removing dust improves the strength of concrete anchors. Use a squeeze bulb or can of compressed air to remove concrete dust from the hole, then vacuum it up.^{[15]XResearch source} Leave your goggles on while doing this to protect from dust and debris.
- Concrete dust can be hazardous to breathe in, so make sure you wear a mask during this process.
- You can also extract the dust by using a damp cotton swab to wipe it out.

Expert Q&A

Search

Add New Question

Question
What is the safest way to drill into concrete?
Gerber Ortiz-Vega
Masonry Specialist
Gerber Ortiz-Vega is a Masonry Specialist and the Founder of GO Masonry LLC, a masonry company based in Northern Virginia. Gerber specializes in providing brick and stone laying services, concrete installations, and masonry repairs. Gerber has over four years of experience running GO Masonry and over ten years of general masonry work experience. He earned a BA in Marketing from the University of Mary Washington in 2017.
Gerber Ortiz-Vega
Masonry Specialist
Expert Answer
Put on the appropriate safety gear, including glasses, a ventilator mask, safety glasses, gloves, and heavy pants. Also, cover any nearby doors or windows with plywood, and move any vehicles out of the area.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 2 Helpful 2
Question
Do you need to water down the concrete when drilling through it?
Community Answer
Though you don't need to water down the concrete, the water will help to collect and remove the drilling dust, which can be hazardous to your health and "clog" the drill bit. The water can also help to keep your bit from overheating, which in turn helps keep the bit from shattering.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 21 Helpful 77
Question
Does cold water and/or dish soap aid in drilling into concrete or help preserve the bit?
Community Answer
Yes, ice cubes would be the ideal thing to use. (That's what I've learned as a granite fabricator.)
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 8 Helpful 17

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

Professionals use a diamond core rig to drill holes with a larger diameter than rotary hammers can achieve.^{[16]XResearch source} The choice of diamond bit depends on the concrete's characteristics, including the size and hardness of its aggregate, how long it's been cured, and whether it is reinforced with rebar.^{[17]XResearch source}
Thanks
Helpful0 Not Helpful0
A second person holding a vacuum cleaner hose (or half a paper plate taped to the wall) just below the hole you're making may save time on cleaning up after yourself.
Thanks
Helpful0 Not Helpful0
Screw into the mortar between blocks, if possible, as it is much easier to drill into mortar than concrete block. Always use lead anchors to hold the screws into place if you drill into the mortar, as screws set in mortar will work themselves loose over time. For some light weight applications (electrical boxes, conduit straps), plastic anchors (with regular screws) or "Tapcon" concrete screws (without anchors) are adequate. (Tapcon screws are easy to identify, as they are blue.) For any application where the screw will be subjected to weight (such as a bench, handrail or shelves) heavy-duty lead anchors should be driven with a hammer after the holes are drilled and then screws driven into the anchors.
Thanks
Helpful0 Not Helpful0

Show More Tips

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Do not bear down on the drill with all your strength. The bit could break.
Thanks
Helpful8 Not Helpful0
The older the concrete, the harder it will be to drill.
Thanks
Helpful44 Not Helpful20
Some carbide-tipped drill bits can shatter when in contact with water.^{[18]XResearch source} If you want to use water to help prevent overheating and reduce dust, read product instructions or contact the bit manufacturer first for instructions on how to do so safely. When using water, be careful not to get the motor of your drill wet.
Thanks
Helpful5 Not Helpful3