How to Disconnect a Washing Machine

A washing machine is not an appliance that is often moved around the house. The machine is usually found in the basement, in a dedicated laundry room, or in the garage, and that is where it stays for most of its life. There are times when the washing machine will need to be moved, however. When the machine is being replaced, or moved to a new home, it will need to be disconnected from the hoses and wires that supply it with power and water. These instructions will guide you through the both the process of disconnecting your machine and getting it ready to move out of its usual location.

Get Product Support Solve Any Problem

Hi there! Do you have a question about how to use or repair your home appliance? I’ve read the manuals so you don’t have to. Select your product, brand, and model, then ask away!

*

Part 1

Part 1 of 2:

Disconnecting Your Machine

Download Article

1
Turn off the water valves. Valves for the supply of hot and cold water are usually located behind the washing machine and in a washer box attached to the wall. Turn off the valves by turning them clockwise until they cannot be turned any further.
- You'll want to turn these off first thing.^{[1]XResearch source} This will protect you from major spills if you should accidentally tear a hose in step 2.
2
Pull or drag the washing machine away from the wall. If working alone, grab one side and move it forward, then do the same with the other side. If you have help, try pulling on opposite sides simultaneously.
- Pull the machine as far out as you can without putting stress on the hoses. Ideally, this will be far enough away from the wall that you can step behind the machine.
- If your house is on the newer side, some new water boxes are above the washer so it's easier to reach the lines without moving the machine.
Advertisement
Make sure the washing machine is not running, and pull the plug out of the outlet. This will disconnect the washing machine from its power supply.^{[2]XResearch source}
Place a water pan or bucket behind the washing machine, under the water lines where it will catch water. Surround the bucket with several towels to catch any additional leaks or water that may spill out when the pipes are detached.
5
Detach the hoses from the machine. If they are attached with clamps, turn the screws atop the clamps counterclockwise until the clamps are loose. Then, point the ends of the hoses toward your bucket to drain any water. Alternatively, you can place them in the drain, located in the washer box.
- It's a good idea to double-check that your valves are still off before doing this. Some styles of faucet handles are easy to accidentally turn back on, and this could have occurred as you moved the machine or when you stepped behind it.^{[3]XResearch source}
- You may find it helpful to wait a few seconds after turning off the valves to try to remove the hoses, as this will allow the pressure in the hoses to abate, making them easier to remove.
- Turning on a few other faucets in the house may help them drain more quickly.
6
Remove the hoses from the wall.Turn the ends counterclockwise until the hoses detach.
- You may need to use adjustable pliers or a pipe wrench to loosen the hoses, especially if the machine hasn't been disconnected in a while.^{[4]XResearch source}
- Once you've removed them, drain any remaining water into the bucket.
7
Remove the drain hose from the drain. Depending on your plumbing setup, this might be a laundry sink, a floor drain, a wall-mounted drain, or a tall stand-pipe. Each of these requires a slightly different process of hose removal. Consult the instructions that came with your machine if it is not immediately obvious.
- Point the free end of this hose toward your bucket as well, to allow any water to flow out.

Part 2

Part 2 of 2:

Preparing the Machine to Be Moved

Download Article

Before moving the machine, get the water bucket out of the way. Wipe up any spills or drips. You wouldn't want to slip while moving the machine.
Ensure there are no additional plugs or hoses connecting the washing machine to the wall. Continue moving the machine out of its place. There may be water inside the washing machine.
If you are keeping this washer, this is a good opportunity to clean the water intakes with a bristle brush to remove any debris that may have accumulated over the years.
4
Remove the power cord. Unless you are setting the machine back up in the same spot, it's a good idea to remove the power cord or, if it is not removable, tape it in place.
- This will protect the plug and prevent the cord from being pulled out accidentally during moving.
- It's also a good idea to remove any knobs that can come off the machine, to prevent loss.
5
Secure the drum. If you will be moving the washing machine any significant distance, it is important to secure the "drum," the inner chamber of the washer that moves.
- Depending on the model of your machine, this can be achieved with special bolts, a large y-shaped piece of foam, or even simply tightening some screws in the back.
- Consult your manual on how best to secure the drum in your machine. You may need to buy a special kit for this.
If you are planning to move the machine any distance, leave your cords attached to the machine. You can tape any dangling cords to the sides of the washer to keep them out of your way.

Expert Q&A

Search

Add New Question

Question
When disconnecting a washing machine, do I need to turn the water off at the mains?
Mark Spelman
Construction Professional
Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
Mark Spelman
Construction Professional
Expert Answer
There should be water supply valves located behind the machine. No need to turn of at the mains, just turn it off there.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 14 Helpful 43
Question
I disconnected my washing machine, and l still have water coming from one of the hoses. What do I do?
Mark Spelman
Construction Professional
Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
Mark Spelman
Construction Professional
Expert Answer
There might be residual water in the line or the valve may be broken.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 8 Helpful 29
Question
My water-valve knob is broken, so I have to turn the water off to the house when moving my washer. We recently sold our home. When we move our washer out, can we just cap the waterline? Or will the pressure not hold the cap?
Mark Spelman
Construction Professional
Mark Spelman is a General Contractor based in Austin, Texas. With over 30 years of construction experience, Mark specializes in constructing interiors, project management, and project estimation. He has been a construction professional since 1987.
Mark Spelman
Construction Professional
Expert Answer
You will need to repair the valve before moving.
Thanks! We're glad this was helpful.
Thank you for your feedback.
If How.com.vn has helped you, please consider a small contribution to support us in helping more readers like you. We’re committed to providing the world with free how-to resources, and even $1 helps us in our mission.Support How.com.vn
Yes No
Not Helpful 6 Helpful 19

See more answers

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Tips

If you have time, after removing the water hoses, let the machine sit for a day or two with the door open. This will allow any remaining water in the machine to dry.^{[5]XResearch source}
Thanks
Helpful0 Not Helpful0
Clear as much clutter and debris as possible from around the washing machine before disconnecting it. Even with the water bucket, it will be nearly impossible to avoid getting water on the ground.
Thanks
Helpful12 Not Helpful5
If your intake hoses are cracked or over five years old, it's a good idea to discard them and replace them with new ones.
Thanks
Helpful0 Not Helpful0

Submit a Tip

All tip submissions are carefully reviewed before being published

Submit

Thanks for submitting a tip for review!

Warnings

Washing machines are very heavy. If you aren't certain that you are strong enough to move one on your own, get help! It may prevent a back injury. An appliance dolly is best, if there's room.
Thanks
Helpful2 Not Helpful1